Instruction Manual for DynaLabs models including: DYN-G-7000, DYN-G-7000 Triaxial MEMS Gyroscopes, DYN-G-7000 Gyroscopes, Triaxial MEMS Gyroscopes, Triaxial Gyroscopes, MEMS Gyroscopes, Gyroscopes
Manuals & Datasheets – Dynalabs
File Info : application/pdf, 8 Pages, 356.27KB
DocumentDocumentModel DYN-G-7000 75°/s / 150°/s / 300°/s / 900°/s Product Manual All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Product Support If at any time you have questions or problems with the DYN-G-6000 sensors, please contact a Dynalabs engineer at: Phone: E-mail: +90 312 266 33 34 (9 a.m. to 5 p.m., UTC +3) info@dynalabs.com.tr Warranty Our products are warranted against defective materials and workmanship for one year. Defects arising from user errors are not covered by the warranty. Copyright All copyrights of this manual belonging to Dynalabs products are reserved. It cannot be reproduced without written consent. Disclaimer Dynalabs Ltd. provides this publication "as is" without warranty of any kind, express or implied, including but not limited to, the implied warranties of merchantability or fitness for a particular purpose. This document is subject to change without notice, and should not be construed as a commitment or representation by Dynalabs Ltd. This publication may contain inaccuracies or typographical errors. Dynalabs Ltd. will periodically update the material for inclusion in new editions. Changes and improvements to the product described in this manual may be made at any time. 2 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Table of Contents 1)Introduction ........................................................................................................................................... 4 2) General Information.............................................................................................................................4 2.1) Unpacking and Inspection.............................................................................................................4 2.2) System Components......................................................................................................................4 2.3) Specifications ................................................................................................................................5 2.4) Outline Drawing............................................................................................................................6 3) Operation and Installation ....................................................................................................................7 3.1) General ..........................................................................................................................................7 5) Declaration of Conformity ...................................................................................................................8 3 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 1) Introduction Dynalabs MEMS based gyroscopes are designed by micro-mechanical silicon structures. Thus, gyroscopes are insensitive to external impacts and vibrations. For harsh environmental conditions Dynalabs gyroscopes are preferred. 7000 Series Triaxial Gyroscopes feature a lightweight, reliable aluminum housing and they have an integrated cable with configurable length and connectors. DYN-G-7000 sensors offer the following options; · Custom Cable Length (5m standard cable) · Custom Housing Material · Custom Connector · Base plate 2) General Information 2.1) Unpacking and Inspection Dynalabs products provide adequate protection for undamaged products to be transported. Document the damages that occur indirectly during the transport and contact the customer representative. 2.2) System Components The DYN-G-7000 has the following components: - MEMS Sensor - Calibration Certificate - Product Manual 4 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 2.3) Specifications Table 1: Specifications datasheet Full scale angular velocity Frequency range Non-linearity (full scale) Noise (in band) Scale Factor (nominal) Scale factor var. overtemp. Bias variation with temp. Shock survivability (°/s) (Hz) (%) (°/s/Hz) (V/°/s) (%) (°/s) (g) DYN-G-7075 DYN-G-7150 DYN-G-7300 DYN-G-7900 ±75 ±150 ±300 ±900 0-150 0-150 0-150 0-150 0.06 0.06 0.06 0.06 0.0075 0.0075 0.0075 0.0075 0.012 0.5 0.006 0.5 0.003 0.5 0.001 0.5 ±1 ±2 ±3 ±4 10,000 10,000 10,000 10,000 Environmental Table 2 Environmental specifications datasheet Protection Level IP 68 Operating Voltage Operating Temperature Operating Current Consumption mA Isolation 5V 20 V -40 °C to +100 °C 21 mA Case isolated 5 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Physical Table 3 Physical specifications datasheet Sensing Element Housing Material Connector (Optional) Mounting Base plate (Optional) Weight (without cable) MEMS Gyroscopes Aluminum or steel D-Sub 9 or 15 pin, Lemo, Binder Adhesive or screw mount Aluminum 12g (aluminum) 29 g (steel) 2.4) Outline Drawing The dimensional properties of DYN-G-7000 sensors are given below. 6 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 3) Operation and Installation 3.1) General The general sensor connector configuration is given below; Cable Code/Pin Configuration: · Red · Black : V + : Ground Power supply voltage +5 V to +20 VDC. Power GND · RX : Yellow : Gyro Signal X-Axis: Analog output voltage signal for single-ended mode. · RY : Blue : Gyro Signal Y-Axis: Analog output voltage signal for single-ended mode. · RZ : White : Gyro Signal Z-Axis: Analog output voltage signal for single-ended mode. WARNING Never connect the power supply and/or the power ground to yellow, blue and/or white cables. Never connect the power supply to the power ground. Always use a clean power source and check the voltage range. 7 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 5) Declaration of Conformity This declaration of conformity is issued under the sole responsibility of the manufacturer. The product(s) are developed, produced and tested according to following EC- directives: · 2014/35/EU Low Voltage Directive (LVD) · 2006/42/EU Machinery Safety Directive · 2015/863/EU RoHS Directive Applied standards: · EN 61010-1:2010 · EN ISO 12100:2010 · MIL-STD-810-H-2019 (Test Methods: 501.7 - High Temperature, 502.7 - Low Temperature, 514.8 - Vibration, 516.8 Shock) DYNALABS MÜHENDSLK SANAY TCARET LMTED RKET declares that above mentioned products meet all the requirements of the above mentioned standards and regulations. Murat Aykan, Technical Manager Ankara, 15.07.2021 8