Cync Product Support Help Center
The leader in LED lighting solutions
Instruction Manual for GE models including: 48717 C-Start Smart Button Switch Timer, 48717, C-Start Smart Button Switch Timer, Smart Button Switch Timer, Button Switch Timer, Switch Timer
GE C by GE Dimmer Smart Switch, Neutral Wire Required, Dimmer Motion Sensor Switch with Bluetooth and 2.4 GHz WiFi, Alexa and Google Compatible without a Hub (Packaging May Vary)
C by GE Neutral Wire- Dimmer 1.5-amp Single-pole/3-way Smart Illuminated Touch Light Switch with Wall Plate, White 043168487177
Cync Neutral Wire Smart Switch- Motion Dimmer 1.5-amp Single-pole/3-way Smart Illuminated Touch Light Switch with Wall Plate, White 043168487337
File Info : application/pdf, 3 Pages, 1.33MB
DocumentDocumentBEFORE YO U DO ANYTHING: Step 1 Turn Off The Power! 1. Turn off the power for the switch location at the circuit breaker box. 2. Test existing switch by toggling switch on/off, ensuring lights do not turn on. 3. Now, follow these setup steps for a single gang switch. Step 2 Remove Your Old Switch 1. Remove the existing wall plate and switch from the wall. 2. Use voltage tester on the black wires to confirm power to the switch is off (recommended). 3. Before disconnecting the wires from the wall, label each with the provided wire labels. A Neutral and ground wires are required. If you don't have either wire, the Cync switch is not compatible. '-,. Disconnect wires and remove existing switch. Step 3 Connect The Wires 1. Connect the neutral (white) wire on the switch to the neutral (white label) wire from the wall. 2. Connect the black line wire from the switch to the line (black label) wire from the wall. 3. Connect the load red wire from the switch with the load (red label) from the wall. '-,. Connect the ground (green) wire on the switch with the ground (green label) wire from the wall. 5. Cap the 3-way/multi-way traveler wire (if applicable). For 3-way switch setup, visit cyncsupport.gelighting.com A Attention: Incorrectly connecting the Neutral or Ground wire from the wall to the Line or Load wire on the switch will damage the product. D --- .._, o=,· Line Load Ground Neutral __. Wire Labels Step '4 Fit Wires Into Wall Box Neatly push the wires back into the box, rotating the switch so it's oriented according to the image. · · 0 0 · For set up help, visit cyncsupport.gelighting.com or call l-8lili-302-29li3. Step 5 Secure The Switch 1. Using a Phillips screwdriver and the screws provided, secure the switch to the wall until level and flush. 2. Screw on the wall plate bracket, then snap the wall plate cover onto the bracket. Congratulations! You've completed the Smart Switch installation. Next... Step 6 Turn The Power Back On After the switch is secured and wall plate mounted, turn the power back on at the circuit breaker box. At the switch, the light ring will flash blue indicating the device is wired correctly and the device is in setup mode. Light ring will continuously flash blue until the switch is added to the Cync App. Light ring will not illuminate if wired incorrectly. IF LIGHTS DON'T TURN ON: 1. Check that air gap switch is depressed. 2. Check that power to the switch is on at the breaker. 3. Turn power off at the breaker, return to the switch to confirm the wires are securely and properly wired according to the installation guide. '-,_ Go to cyncsupport.gelighting.com for more troubleshooting. Download the CYNC App Add your Smart Switch to the CYNC App Set up your Alexa or Hey Google voice assistant (optional) Enable Your Voice Assistant Connect to your Amazon Alexa or Hey Google voice assistants in the CYNC App. Then try this... Alexa, turn off the living room. Alexa, turn on the bedroom. Alexa, set kitchen to 50% Hey Google, turn on the lights. Hey Google, good morning. Hey Google, I'm leaving. Depressed, socket powered Pulled out, no power to socket