Lian Li LANCOOL207 PC Case Installation and Assembly Guide
Procedure to Remove All Exterior Panels and Dust Filter
[!] Remove the protecting clip. It is recommended to keep the protecting clip on for transportation.
Remove the side panel, top mesh panel, and side glass panel.
Remove the front pillar and the top fan bracket screws (2 x 2 screws).
Remove the dust filters.
Ensure the front pillar is secured and the top fan bracket screws are tightened for transportation.
Peel off the protective film on both sides.
Case Overview
The LANCOOL207 PC case supports two primary configurations: Mesh Mode and Vision Mode.
Features:
- Power Button
- Fan Support:
- Removable fan bracket: Supports 120 mm fan x 2
- Removable fan bracket: Supports 120 mm fan x 3 or 360 mm radiator x 1
- Removable fan bracket: Supports 120 mm fan x 3 or 140 mm fan x 2 or 360 mm radiator x 1 or 280 mm x 1
- IO Ports: 1x Audio/Microphone Combo Jack, 2 x USB 3.0, 1x USB 3.2 Type C
- Storage:
- Removable Toolless SSD tray: Supports 2.5" SSD x 2
- Removable HDD cage: Supports 3.5" HDD x 2 or 2.5" SSD x 2
- PSU Tray: Supports ATX PSU x 1
Transform to Vision Mode
Switch to the top glass panel configuration for Vision Mode.
The process involves steps numbered 1 through 5, with step 5 requiring 3 units of a specific component.
Included Accessories Kit List
- Top glass panel
- Spare parts
- Tool
Motherboard Installation
For standard motherboard installation, remove the silicone cover to allow the CPU 8-PIN cable to pass through.
The case supports standard ATX, M-ATX, ITX, and reversed ATX motherboards.
I/O Port Function and Cable Connection
Details on I/O port functions and corresponding cable connections are provided.
Hardware Clearance
- CPU height clearance: 167 mm
- PSU clearance: Sufficient space for ATX PSUs.
- GPU clearance: 408 mm
PSU Installation
Two methods are available for PSU installation:
- Method 1: Direct Installation
- Method 2: Remove the bracket and Install
Cable Management
Dedicated paths are available for routing cables:
- Path for CPU 8-PIN cable
- Path for 24-PIN cable
- Path for FIO module
To optimize cable management, remove the hard drive cage for extra space.
Utilize the provided cable holders for large cables and velcro straps for small cables.
A velcro strap can be removed to accommodate a controller.
Drive Installation
Drive installation can be performed using two methods:
- Method 1: Swing 180° to open
- Method 2: Remove the drive bay/cage
[!] Be careful of the rubber pad installation orientation.
Radiator & Cooling Support
The case offers flexible cooling configurations:
Vision Mode:
- Supports 2 x 120 mm fans
- Supports 3 x 120 mm fans or 1 x 360 mm radiator
- Supports 2 x 140 mm fans
- Supports 1 x 360 mm radiator
- Supports 1 x 280 mm radiator (Total thickness 98mm)
- Supports 2 x 120 mm fans
Mesh Mode:
- Supports 3 x 120 mm fans or 1 x 360 mm radiator (multiple locations)
Fan Bracket Installation
Installation involves inserting tabs, removing existing brackets, and installing new ones. This process may require up to 3 units of a specific component (e.g., screws).
Remove the Side Fan Bracket
To remove the side fan bracket, lift it and pull it out from its groove.
There are two installation scenarios: inner or outer mounting.
Note the thickness limit for side fan bracket installation.
Side AIO Tube Rear Routing Guide
For routing AIO tubes through the rear, after disconnecting at the grommet, pass the AIO pump from the back to the front.
[!] Install the side fan bracket in the inner scenario for this type of installation.
For Hydroshift LCD AIO installations, specific components may need to be removed.
If the AIO pump is too large to pass through the grommet, remove the grommet, pass the pump, position it on the tubes, and then replace the grommet.
Fans can be installed in the main chamber.
The guide demonstrates AIO tube routing for GA II Trinity and other standard AIOs.
A specific bracket needs to be removed only for HydroShift LCD 360R and 360TL models.
The guide also demonstrates Hydroshift LCD AIO tube routing.
[!] GA II Trinity performance is not compatible with this type of installation.
Graphic Card Anti-Sag Bracket Installation
Follow similar installation steps for the graphic card anti-sag bracket.
This bracket supports GPUs longer than 278 mm.
To install or remove the bracket, first remove the side fan bracket.
[!] Pay attention to the orientation when reinstalling components.
During regular assembly, there is no need to remove the front glass panel.
If necessary, the front glass panel can be removed.
