Aputure Spotlight Mini: Product Manual and Installation Guide

1. Installing the Spotlight Mini

Installing on a Light Stand

1. Mount the Spotlight Mini onto a compatible light stand. (See Figure 1)
2. Rotate the tilt-lock handle in the direction shown in Figure 2 to secure the yoke in place.
3. Insert the Spotlight Mini into the Mini ProLock mount on the STORM 80c and rotate the locking handle to secure it, as shown in Figure 3.
4. Connect the adapter and power cable to the fixture, and turn on the light to begin use.

Note: Always ensure the lighting fixture is powered off before installing or removing the Spotlight Mini.

Figure 1 Description: Shows the Spotlight Mini being mounted onto a light stand with a connection point labeled '1'.

Figure 2 Description: Shows the tilt-lock handle being rotated to secure the yoke, indicated by '2'.

Figure 3 Description: Illustrates inserting the Spotlight Mini into the STORM 80c's Mini ProLock mount and securing it with a locking handle, indicated by '1' and '2'.

Installing Using the 3/8-16in Screw Mount

1. The Spotlight Mini features a 3/8"-16 mounting point with anti-twist sockets for secure rigging.
2. When rigging the Spotlight Mini using the 3/8"-16 mount, always attach a safety cable as an additional safety precaution.
3. For increased stability, the 3/8"-16 mounts on the STORM 80c can also serve as supplementary mounting points.

Figure Description: Depicts the 3/8"-16 mounting point on the Spotlight Mini and its connection to the STORM 80c, with labels '1' and '2' indicating connection points.

2. Installing, Removing, & Focusing the Spotlight Mini Lens

Installing the Lens

1. If necessary, loosen and remove the focus locking knob from the body of the Spotlight Mini.
2. Align the lens with the slot, and insert it into the body of the Spotlight Mini.
3. Once fully inserted, reattach and tighten the focus locking knob to secure the lens.

Figure 4 Description: Shows the process of aligning and inserting the lens (labeled '1') and then tightening the focus locking knob (labeled '2').

Removing the Lens

1. Loosen and remove the focus locking knob.
2. Carefully remove the lens from the body of the Spotlight Mini.

Figure 5 Description: Illustrates loosening the focus locking knob (labeled '1') and then removing the lens (labeled '2').

Focusing the Lens

Adjust the clarity of the projected image by sliding the lens forward or backward, then tighten the focus locking knob to secure the position.

Tip: The minimum focusing distance for both the 19° and 36° lenses is 70 cm. For optimal image clarity, a focusing distance of 3m is recommended.

3. Installing the Gobo Holder (M-Size)

1. Insert an M-size Gobo (compatible with both metal and glass types) into the Gobo Holder, as shown in Figure 6.
2. Insert the Gobo Holder into the Gobo Slot on the Spotlight Mini, as shown in Figure 7.
3. Ensure the Gobo Holder is oriented correctly for smooth operation—its handle should face the Iris slot for proper alignment.

Note: Some components may deform slightly or show signs of smoke or discoloration after prolonged exposure to high temperatures. This is expected behavior. However, melting plastic parts or excessive smoke is considered abnormal and may indicate a malfunction.

Figure 6 Description: Shows an M-size Gobo being inserted into the Gobo Holder.

Figure 7 Description: Depicts the Gobo Holder being inserted into the Gobo Slot on the Spotlight Mini, with the Gobo Holder handle indicated.

4. Installing the Iris (M-Size) (sold separately)

1. Insert the M-size Iris into the Iris slot on the Spotlight Mini in Figure 8.
2. Adjust the Iris handle to control the size of the aperture and achieve the desired beam shape.

Note: The Iris is not included and must be purchased separately. To avoid injury, do not place your fingers inside the Iris while adjusting.

Figure 8 Description: Illustrates inserting the Spotlight Mini Iris and adjusting the handle to achieve the desired beam size.

5. Installing the Gel Holder

1. As shown in Figure 9, lift and rotate the spring-loaded latch to open the gel holder slot.
2. Insert the Gel Holder into the slot, as shown in Figure 10.
3. Rotate the spring-loaded latch back to its original position to secure the Gel Holder in place.

Figure 9 Description: Shows lifting and rotating the spring-loaded latch to open the gel holder slot, indicated by '1'.

Figure 10 Description: Depicts inserting the Gel Holder into the slot (labeled '2') and then securing it by rotating the latch back (labeled '3').

6. Operating the Four-Leaf Shutters

The Spotlight Mini is equipped with four internal shaping shutters that allow precise control over the beam shape. Each shutter can be independently adjusted by sliding it in and out to control the shape, or by rotating each shutter to change the angle of the cut.

Diagram Description: Shows the four-leaf shutters, with arrows indicating "Slide in and out" and "Rotate the shutter handle".

7. Operating the 360° Rotating Barrel

The Spotlight Mini features a 360° rotating barrel, allowing you to freely rotate the projection assembly to adjust the orientation of the gobo pattern or the angle of the four-leaf shutters. 1) Grab the body and rotate the barrel to the desired angle. 2) Use the degree markings to accurately reference and reproduce rotation positions for consistent framing.

Diagram Description: Illustrates grabbing the Spotlight Mini body and rotating the barrel, with arrows indicating rotation and highlighting degree markings.

8. Carrying Case Contents

The carrying case includes:

• Spotlight Mini
• 19°/36° Spotlight Mini Lens
• Gobo Holder (M-Size)
• Gobos (M-Size)
• Iris (M-Size) (sold separately)
• User manual

Diagram Description: Shows the open carrying case with compartments for the Spotlight Mini, lens, gobo holder, gobos, iris, and user manual.

Photometrics

a. Illuminance values at different distances and color temperatures with STORM 80c.

Note: The above data is the average data measured in the laboratory. The brightness, color temperature and other parameters of different lights will have slight differences.

Safety Instructions

When using this modifier, the following basic safety precautions should always be followed:

1. Read and understand all instructions before use.
2. Close supervision is necessary when any fixture is used by or near children. Do not leave the fixture unattended while in use.
3. Use caution, as burns can occur from touching hot surfaces.
4. Allow the fixture to cool completely before storing.
5. To reduce the risk of injury, always install or disassemble the fixture properly.
6. Do not use accessory attachments not recommended by the manufacturer, as they may increase the risk of fire, electric shock, or injury.
7. Do not place the fixture near flammable objects.
8. Only use a dry microfiber cloth to clean the product.
9. This product is RoHS certified. Please operate it in full compliance with applicable standards. Note: This warranty does not cover damage caused by misuse or malfunction; however, repairs may be available on a chargeable basis.
10. The information in this manual is based on thorough, controlled testing procedures. Specifications are subject to change without prior notice.

SAVE THESE INSTRUCTIONS

Disclaimer

Before using this product, please read the product manual to ensure correct use and complete understanding. After reading, please keep the product manual properly for future reference. Improper operation of this product may result in severe personal injury to yourself or others, as well as potential damage to the product and loss of property. When using this product, it shall be deemed that you have understood, recognized, and accepted all clauses and contents of this document. Users assume responsibility for their own conduct and any resulting consequences. Aputure is not liable for any damages suffered as a result of the user's failure to use the product in accordance with the Product Manual.

Please visit the official Aputure website for the latest product information.