Dynalite | Philips lighting
Instruction Manual for PHILIPS models including: Dynalite DMC4 UL, DCM-DyNet, Communication Module, DCM-DyNet Communication Module, Dynalite DMC4 UL DCM-DyNet Communication Module
Philips Dynalite DMC4 CE
File Info : application/pdf, 4 Pages, 1.10MB
DocumentDocumentDCM-DyNet Communications Module Installation Instructions Instructions d'installation Installationsanweisungen Instrucciones de instalación Istruzioni per l'installazione Installatie-instructies Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux. Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren. Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras. I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici. De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften. / . 60 mm (2.36 in) 94 mm (3.70 in) 1 BUS RJ12 DMC2/ DMC4 305 mm (12.01 in) D D+ GND +24 V-OUT IN GND GND IN 4 GND IN 3 IN 2 GND IN 1 +V D D+ GND SHLD RJ12 DMX Rx IEC Overvoltage Category III 2xRJ12 UL924 DRY CONTACT INPUT INPUTS RS-485 DyNet 1 ¡ ¢ £¤ 1¡ ¥¦ ¡ ¢ £0§¡ ¥¦ 12/24 V 200 mA 90% 2 DyNet 12V 24V 3 ON DMX 512 OFF DMX TERM DMX 512 4 1 Nm 8.8 Lb-in IEC Pollution Degree II 2 DMC2 DMC4 5 UL924 DRY CONTACT INPUT INPUTS D D+ GND GND GND D+ D+12/24 V +12/24 V +24V UL924 GND GND IN4 GND IN3 IN2 GND IN1 +V D D+ GND SHLD 6 i RS-485 DyNet/DMX Rx ii 1 GND 2 GND 3 D+ 4 D 5 +12/24 V 6 +12/24 V RS-485 DyNet iii RS-485 DyNet 2 A 2.5 mm2 12+ AWG 0.5 Nm 4.4 Lb-in DMX DMX Rx TERM RJ12 RJ12 7 A DMC2 DSM2 1 2 DCM-DyNet RS-485 DyNet 7B DMC4 1 2 $© 3 4 $¨©$# RS-485 DyNet 3 8 9 DMC2 DMC4 10 11 12 DMC2/DMC& DMC2/DMC4 RS-485 DyNet CDoCmMm-uDnyiNcaettion Module DCCoMm-mDuynNiceat tion Module Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user's authority to operate this device. Installation of a home and building automation and control system shall comply with HD 60364-4-41. The temperature limits and current-carrying capacities for the communication wires specified in HD 384.5.523 shall not be exceeded. This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la classe B est conforme a la norme NMB003 du Canada: CAN ICES-3(B)/NMB-3(B). © 2021 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners. www.lighting.philips.com/dynalite AZZ 432 0821 R14