Boost Static Back To Back Frame Assembly Guide
Component Parts
| NO. | Component Name | PCS | NO. | Component Name | PCS |
|---|---|---|---|---|---|
| 1 | Column | 4 | 9 | Screen brackets | 4 |
| 2 | Side Bracket | 4 | 10 | Bolts M6x10 | 14 |
| 3 | ST4x20 | 40 | 11 | Connected beam | 2 |
| 4 | Rubber pad | 24 | 12 | Centre bracket | 2 |
| 5 | Bolts M6x12 | 8 | 13 | Allen Wrench(6mm) | 1 |
| 6 | Top frame -1 | 2 | 14 | Allen Wrench(4mm) | 1 |
| 7 | Centre rails | 4 | 15 | Cable Tie | 10 |
| 8 | Top frame-2 | 2 |
Diagram shows an exploded view of the desk frame components, with numbered labels corresponding to the parts list. Key components like columns, top frames, rails, and brackets are visible.
Assembly Instructions
Step 1: Adjust Top Frame Length
Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
Diagram shows two horizontal top frame pieces being extended outwards, indicated by opposing arrows. A magnified inset view shows loosened bolts on one of the frame pieces.
Step 2: Attach Columns
Insert the column into the top frame and fix the lifting column with 4 pieces of M6x12 screws.
Diagram shows columns being inserted into the top frame. A magnified inset view shows a column being secured to the top frame with screws, indicated by downward arrows.
Step 3: Attach Side Brackets
Place the side bracket on the top frame and tighten the bolts.
Diagram shows side brackets being placed onto the top frame assembly. Arrows indicate the points where bolts will secure the brackets.
Step 4: Install Screen Brackets
Install the screen brackets with 8 pieces of M6x10 Bolts.
Diagram shows screen brackets and associated M6x10 bolts, illustrating their placement for attachment.
Step 5: Insert Connected Beam
Insert the connected beam and tighten the pre-installed bolts.
Diagram shows the connected beam being fitted horizontally between the two vertical columns. A magnified inset view shows the beam being secured with bolts.
Step 6: Mount Tabletop and Fix Centre Bracket
Mount the tabletop and fix it with 26 pieces of ST4x20 screws. Fix the centre bracket with 2 pieces of M6x10 screws.
Diagram shows the tabletop being placed onto the assembled desk frame. Screws are indicated for attaching the tabletop. The centre bracket is also shown being attached to the frame.
Cable Tray Installation
Fix the cable tray (B2-B2BCT) to the back-to-back desk frame with 8 pieces of M6x10 screws.
Diagram illustrates the cable tray being attached to the underside of the back-to-back desk frame using screws.
Screen Panel Installation
Shush30 Privacy Screen Installation
Step 1
Insert the tapped plates into the screen panel. Plates can be found in the B2-BBRAC carton.
Diagram shows tapped plates being inserted into the edge of a screen panel. A magnified inset view shows the plates and screws used for attachment.
Step 2
Install the screen brackets (B2-BBRAC) to the Shush30 Extrusion with 8 pieces of M5x6 screws.
Diagram shows screen brackets being attached to the extrusion of the screen panel. A magnified inset view shows the bracket and screw attachment.
Step 3
Fix the screen brackets (B2-BBRAC) to the desk frame with 8 pieces of M6x10 screws.
Diagram shows the screen panel, with attached brackets, being mounted onto the desk frame. Screws (M6x10) are indicated for securing the brackets to the frame.
EPS (900mm H Eco Panel) Screen Panel Installation
Step 1
Install the screen brackets (B2-BBRAC) with 8 pieces of M6x10 Screws. The brackets' direction is shown in the photos.
Diagram shows screen brackets being attached to the desk frame. A magnified inset view highlights the bracket orientation and screw (M6x10) placement.
Step 2
Place the EPS panel on the screen brackets. Using a 6mm drill bit (not included), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes. Note: Carbide Drill Bits Work Best For PET panel. Place 8 x Double Ended Bolts M5*32mm - 6mm through the screen bracket (B2-BBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with an Allen key.
Diagram shows the EPS panel being placed onto the screen brackets. A magnified inset view illustrates drilling holes in the panel and securing it with double-ended bolts (M5*32mm) and an Allen key.