Owner's Manual for iskydance models including: V1 Plus RT1 Single Color LED Controller Kit, V1 Plus RT1, Single Color LED Controller Kit, LED Controller Kit, Controller Kit
Malfunctions analysis & troubleshooting 1. The product shall be installed and serviced by a qualified person. 2. The product is non-waterproof.
Remote control or connected with external push switch to achieve on/off and dimming function. ○ Ultra sensitive brightness adjustment touch wheel.
Single Color LED Controller Kit Model No.: V1 + RT1 1 channels constant voltage/Touch color wheel/Step-less dimming/Wireless remote 30m distance Feature Remote control or connected with external push switch to achieve on/off and dimming function Ultra sensitive brightness adjustment touch wheel Smooth dimming and switch without any ickering 4 scene memory Auto-transmitting function: Controller automaticlly transmit signal to another controller with 30m control distance Light on/off fade time 3s selectable Technical Parameters RED LED Receiver's Input and Output Input voltage 5-36VDC Input current 8.5A Output voltage 5-36VDC Output current 1CH,8A Output power 40W/96W/192W/288W (5V/12V/24V/36V) Output type Constant voltage Dimming data Dimming level Dimming range Dimming curve PWM Frequency 4096 levels 0 -100% Logarithmic 2000Hz Warranty and Protection Warranty 5 years Protection Reverse Polarity LED Remote's Input and Output Output signal Working voltage RF(2.4GHz) 3VDC(AAAx2) Working current 5mA Standby current 10A Standby time 2 year Remote distance 30m Safety and EMC EMC standard (EMC) Safety standard(LVD) Radio Equipment(RED) Certification ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 ETSI EN 300 328 V2.2.2 CE,EMC,LVD,RED Environment Operation temperature Case temperature (Max.) IP rating Ta: -30 OC ~ +55 OC T c: +85OC IP20 User Manual Ver 1.0.4 Mechanical Structures and Installations LED indicator Push switch com Push switch in Installation rack Match key 53.00 mm 17.50 mm 33mm V1+ RT1 Single Color LED Controller Kit LED output LED output + Power input Power input + Installation rack 97mm 122.00 mm Wiring Diagram Push Switch 18mm V1 LED Controller Single color LED strip + RF remote V1 LED Controller AC100-240V Power Supply 5-36VDC Constant Voltage Single color LED strip + Page 1 Remote function 30s S1 S2 S3 S4 : Turn on/off light. : Touch to change brightness. : Adjust brightness, short press 10 levels, long press 1-6s for continuous 256 levels adjustment. : Small night brightness (10%). 30s : Turn off light after 30s, long press 2s will turn off light after 60s. : 25%, 50%, 75%,100% brightness. S1 S2 S3 S4 : Short press recall the scene, long press 2s save current brightness into S1/2/3/4. the LED indicator display green when save OK. Match Remote Control (two match ways) End user can choose the suitable match/delete ways. Two options are offered for selection: Use the controller's Match key Use Power Restart Match: Short press match key, immediately press on/off key of the remote. Match: Switch off the power, then switch on power, repeat again. Immediately short press on/off key 3 times on the remote. The light blinks 3 times means match is successful. Delete: Press and hold match key for 5s to delete all match, The light blinks 5 times means all matched remotes were deleted. .Delete: Switch off the power, then switch on power, repeat again, Immediately short press on/off key 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. Light on/off fade time Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s. PWM duty(%) Dimming Curve 100 Gamma=1.6 90 80 70 60 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 Brightness(%) V1+ RT1 Single Color LED Controller Kit Malfunctions analysis & troubleshooting Malfunctions No light Uneven intensity between front and rear,with voltage drop No response from the remote Causes 1. No power. 2. Wrong connection or insecure. 1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability. 1. The batter y has no power. 2. Beyond controllable distance. 3. The controller did not match the remote. Troubleshooting 1. Check the power. 2. Check the connection. 1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater. 1. Replace batter y. 2. Reduce remote distance. 3. Re-match the remote. Safety information 1. The product shall be installed and serviced by a qualified person. 2. The product is non-waterproof. Please avoid the sun and rain. 3. Good heat dissipation will prolong the working life of the controller. Please ensure good ventilation. 4. Please check if the output voltage of any power supplies used comply with the working voltage of the product. 5. Ensure all wire connections and polarities are correct and secure before applying power to avoid any damages to the LED lights. 6. If a fault occurs please return the product to your supplier. Do not attempt to fix this product by yourself. User Manual Ver 1.0.4 Page 2Corel PDF Engine Version 16.1.0.843 CorelDRAW X6