Instruction Manual for Anolis models including: CALUMMA M LED Light, CALUMMA M, LED Light, Light
INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC QR code for Installations Instructions ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 1 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC Fixture must be installed by a qualified electrican in accordance with all national and local electrical and construction codes and regulations. This device falls under class one and must be grounded! CALUMMA M CALUMMA L STEP 1 CALUMMA INSTALLATION USING YOKE 1 Use fasteners that are appropriate for use with your mounting surface CALUMMA XL Drill two holes into the surface according the given dimensions(Calumma M/L/XL) 2 3 Adjustability Fasten the Yoke of the fixture to the surface by two washers, spring washers and screws. Use an Allen key to release M8 tilting lock on each side of luminaire and adjust tilt of LED module in range of +180°/-180°. ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 2 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC STEP 2 CABLE GLAND INSTALLATION Slip the cable through the gland according to the picture below and do not assemble the gland yet. Use wrench size 22 for cable gland M20x1.5 STEP 3 CONNECTION - CE (JUNCTION BOX IS NOT PART OF THE PACKAGE) A DALI WIRE Black White Green/Yellow Connection colour coding POWER CONNECTION WIRE L Red N Orange / DATA CONNECTION Data + (+) Data - (-) Data 0V (0) Strip these lengths for cable connections. Power Connection Data Connection A 9mm 9mm Connection colour coding Core (EU) Core (US) Power Connection colour coding L N GROUND Brown Black Blue White Green/Yellow Green DALI Calumma Power next Junction Box B DMX WIRE Black Blue Green/Yellow Connection colour coding POWER CONNECTION WIRE L Red N White Shielding DATA CONNECTION Data + (+) Data - (-) Data 0V (0) Junction Box DMX Calumma Power next Junction Box Junction Box ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 3 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC C WIRELESS DMX - each fixture WIRE Black Blue Green/Yellow Connection colour coding POWER CONNECTION WIRE L Red N White Shielding DATA CONNECTION Data + (+) Data - (-) Data 0V (0) Power Calumma next Junction Box D WIRELESS DMX - first fixture WIRE Black Blue Green/Yellow Connection colour coding POWER CONNECTION WIRE L Red N White Shielding DATA CONNECTION Data + (+) Data - (-) Data 0V (0) Junction Box Power Calumma next Junction Box Junction Box E DMX or ETHERNET via E-Box WIRE Black Blue Green/Yellow Connection colour coding POWER CONNECTION WIRE L Red N White Shielding DATA CONNECTION Data + (+) Data - (-) Data 0V (0) DALI Calumma Power next Junction Box Junction Box ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 4 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC F DMX or ETHERNET via E-Box with Leader and Jumper Cable FA FB LOCK 1 2 Please align the arrow symbol and mate the connector. Do NOT rotate the connector. Correct connection should be signalized by silent ,,click" sound. UNLOCK 1 Mating complete. 2 Rotate NUT 30 degrees anti-clockwise, same as the arrow direciton. (Please do not rotate clockwise during unmating process) CONNECTION - US (JUNCTION BOX IS NOT PART OF THE PACKAGE) A DALI WIRE Black White Green/Yellow Connection colour coding POWER CONNECTION WIRE L Red N Orange / DATA CONNECTION Data + (+) Data - (-) Data 0V (0) Drop out. DALI Calumma Power next Junction Box Junction Box ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 5 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC B WIRELESS DMX - each fixture Connection colour coding WIRE POWER CONNECTION WIRE Black L Red White N Orange Green/Yellow Blue DATA CONNECTION Data + (+) Data - (-) Data 0V (0) Power Calumma next Junction Box C WIRELESS DMX - first fixture Connection colour coding WIRE POWER CONNECTION WIRE Black L Red White N Orange Green/Yellow Blue DATA CONNECTION Data + (+) Data - (-) Data 0V (0) D DMX or ETHERNET via E-Box Connection colour coding WIRE POWER CONNECTION WIRE Black L Red White N Orange Green/Yellow Blue DATA CONNECTION Data + (+) Data - (-) Data 0V (0) Power Junction Box Calumma next Junction Box Power Junction Box Calumma next Junction Box STEP 4 CABLE GLAND INSTALLATION Assemble the cable gland according to the picture. Use wrench size 22 for cable gland M20x1.5 Install Cable glands individually! We recommend to apply an adequate layer of the paste LOCTITE 5331 on the plastic holder of the cable gland before inserting in into the body of the gland and an adequate layer of the paste LOCTITE 577 on the thread of the gland body. Failure to properly install cable glands will result in failure of the water tight seal! Junction Box ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 6 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC STEP 5 INSTALLATION OF ACCESORIES HALF TOPHAT TOPHAT OPTICAL DEMO SET 1 2 Screw-out 4 screws from the cover plate. 3 Remove the cover plate. 4 Place the accessories (TOPHAT, HALF TOPHAT, OPTICAL DEMO SET) onto luminaire and centre it. Fasten the accessories (TOPHAT, HALF TOPHAT, OPTICAL DEMO SET) to the luminaire by the 4 packed-in washers and screws. ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 7 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC 5 Only for Optical Demo Set FLOOR STAND Slide the Optical foil into the space of Optical Demo Set. 1 2 Place the luminaire on tenon on the Floor Stand. POLE ADAPTOR The Luminaire fasten by one washer one flexible washer and one nut closed. A Installations on POLE(diameter 76-116mm) with two screws. ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 8 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC B C Installation on FLAT POLE with two screws. A1 Installation on POLE (diameter 76-116mm) with zip ties. Maximum width zip ties is 20mm (not included packing). A2 Drill three holes into the surface according the given dimensions. A3 Pole Adaptor must be installed with two holes up Insert the cable gland into the middle hole. A4 Fasten the Pole Adaptor on the surface by two screws, spring washers and washers. Fasten the Luminaire on the Pole Adaptor by three screws, spring washers and washers. ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 9 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC B1 B2 Drill three holes into the surface according the given dimensions. B3 Pole Adaptor must be installed with two holes up Insert the cable gland into the middle hole. B4 Fasten the Pole Adaptor on the surface by two screws, spring washers, washers and spacers. C1 Fasten the Luminaire on the Pole Adaptor by three screws, spring washers and washers. C2 Drill one hole into the surface according the given dimension. Insert the cable gland into the hole. ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 10 INSTALLATION INSTRUCTIONS CALUMMA M / L / XL SC AND MC C3 C4 Pole Adaptor must be installed with two holes up Installations Pole Adaptor with two zip ties. FOR ALL INSTALLATION VERSIONS Fasten the Luminaire on the Pole Adaptor by three screws, spring washers and washers. Pull the cable through the inside of the Pole Adaptor and the cable gland and return to STEP 3. ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com VERSION 3.0 / 2_2023 11Adobe PDF Library 17.0 Adobe InDesign 18.1 (Windows)