BodegaCooler Car Fridge User Manual

1. Safety Instructions

WARNING!

• Do not operate the appliance if it is visibly damaged.
• Do not block the gaps of the fridge with things like pin, wire, etc.
• Do not expose the appliance to rain or soak it in water.
• Do not place the appliance near naked flames or other heat sources (heaters, direct sunlight, gas ovens etc.).
• Do not store any explosive substances like spray cans with a flammable propellant.
• Ensure the supply cord is dry and not trapped or damaged. Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.
• Check the voltage specification on the type plate corresponds to that of the energy supply. The appliance is only to be used with the power supply unit provided with the appliance.
• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
• Once unpacked and before turning on, the appliance must be placed on a level surface for more than 6 hours.
• Make sure that the appliance stays horizontally when it is running. The tilt angle must be less than 5° for long time running and be less than 45° for short time running.
• Keep the ventilation openings in the unit casing or in the built-in structure free of obstacles. (Around the compressor≥100mm).
• Keep the appliance stable on the ground or in the car; do not drain upside down.

CAUTION!

• Repairs may only be carried out by qualified personnel. Incorrect repair may cause danger.
• The lamp and supply cord must be replaced by the manufacturer or qualified persons.
• The installation of DC power in the boat must be handled by qualified electricians.
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they've been given supervision or instruction concerning use of the device in a safe way and understand the hazards.

NOTICE!

• Disconnect the power supply before each cleaning and maintenance and after every use.
• Do not use sharp tools to defrost: Do not damage the refrigerant circuit.
• Risk of child entrapment: Before you throw away your old refrigerator or freezer: take off the doors; leave the shelves in place so that children may not easily climb inside.
• Check if the cooling capacity of the appliance is suitable for storing the food or medicine.
• Food may only be stored in its original packaging or in suitable containers.
• If the appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould developing within the appliance.

The appliance is intended to be used in household and similar applications such as:

• Staff kitchen areas in shops, offices and other working environments;
• Camping, Farm houses and by clients in hotels, motels and other residential environments;
• Bed and breakfast type environments;
• Catering and similar non-retail applications.

Please according to local regulations regarding disposal of the appliance for its flammable refrigerant and blowing gas.

2. Product Features

• High-efficiency DC compressor and conversion module.
• CFC free and great heat insulation.
• DC 12V/24V or AC 100~240V (using dedicated adapter) power supply.
• Fast cooling to -20°C/-4°F (based on 25°C/77°F room temperature).
• Intelligent battery protection system.
• LED display for temperature setting.
• Cup holder design and adjustable door opening direction.

3. Product Structure

A diagram shows the structure of the car fridge. Key components include:

• Door latch
• Sealing strip
• Storage room
• Control panel
• Handle
• Machine compartment
• Charging port

4. Reverse Door Opening Direction

The door can be opened in two directions and can be detached at a 20° angle. To reattach, align the door shaft with the compartment hole and insert it.

Diagrams illustrate the process of reversing the door opening direction, showing the door shaft and the corresponding hole.

5. App Connection

WiFi MODEL: Scan the QR code provided with your smartphone or search for "QZsmart" in the App Store or Google Play to download the app.

PREPARATION BEFORE USE:

1. Ensure your car fridge is on and your smartphone is connected to a 2.4 GHz Wi-Fi network.
2. Note: This device operates exclusively on 2.4 GHz Wi-Fi® networks.
3. Ensure the Bluetooth function of your mobile phone is enabled; otherwise, the device cannot be automatically searched.
4. Download the QZsmart app from the App Store or Google Play™.
5. Note: Authorize the app to access network and location services.
6. For first-time app users, click the "Sign up" button to register. If you have an account, click "Log in".
7. For optimal Wi-Fi connection, reset the product's Wi-Fi before first use. This can be done by turning off the refrigerator's switch and simultaneously long-pressing the + and - buttons on the control panel for 3 seconds until one beep is heard.

Add Device:

1. From the Home Page, press "Add Device" or the [+] icon in the top right corner of the screen. (If a device is already added, the "Add Device" button may not appear).

Connecting:

Auto-connect (Featured First): The app automatically searches when Wi-Fi and Bluetooth are on, allowing you to add the product directly.

1. Press "Add Device" or "+".
2. When the device is found, press "Add". Bluetooth must be enabled during this process.
3. Select your Wi-Fi network (ensure it is a 2.4G network).
4. Enter your router password.
5. Wait for connection and click "NEXT".
6. Once added, you can rename and locate the device via the menu.
7. Click "Done" when finished.

Manual connection: Select your model from the device menu.

1. Press "Add Device" or "+".
2. Select the corresponding product type and click the product diagram of the model.
3. After the product is shut down, press "Next".
4. Long pressing + and - on the control panel for 3 seconds and hearing one beep, press "Next".
5. Select your Wi-Fi network (ensure it is a 2.4G network).
6. Enter your router password.
7. Click "Confirm". The next screen will say "Connect your mobile phone to the device's hotspot".
8. Click "Go to connect". This will take you to your phone's settings (or Wi-Fi list for Android).
9. Select "SmartLife-XXXX".
10. Navigate back to the QZsmart App.
11. Click "Next". Your smartphone will automatically connect.
12. Once the device is added, you can use the menu to change the name and location of the device.
13. When you are finished, click "Done".

Follow the APP interface for detailed operation reminders. Note: Device connection may take up to 60 seconds. Once added, you can rename the device via the app's menu.

BLUETOOTH MODE: Bluetooth function can be used in non-Wi-Fi environments.

PREPARATION BEFORE USE: Please be sure to connect Wi-Fi successfully first. (Again, you must connect to Wi-Fi first; otherwise, you will not be able to use Bluetooth in non-Wi-Fi environments.)

NOTE: After the Wi-Fi connection is disconnected, wait about 2-3 minutes before you can directly use the Bluetooth control.

Using the My App: The main interface can control the switch, set "temperature" and "lock". Click "more features" in the lower right corner to set the switch of temperature unit, cooling mode, battery protection mode.

Screenshots of the app show temperature control, mode selection (MAX, ECO), and battery protection (H, M, L).

How to unbind: A car refrigerator can only be connected to one mobile phone.

First method: Disconnect by turning off the refrigerator's switch and simultaneously long pressing + and - on the control panel for 3 seconds, then hearing one beep.

Second method: Remove connection via the app: Open the app, go to the device page, click the [menu] icon in the upper right corner, and then click "Remove Device" at the bottom.

Cautions:

• There may be a delay (1-3 minutes) in operating the machine via the mobile phone; please be patient.
• The app's language automatically switches with the mobile system's language.
• You can lock or unlock the control panel using the app's lock icon. The refrigerator's operation panel does not have a locking function.

6. Function and Operation

A diagram shows the control panel and display. Key indicators include:

• Set: Control panel
• -20°C: Current Temperature (display can show °C or °F)
• -20°C: Temperature Setting
• Voltage: 13.5V (example)
• Mode: MAX (Fast cooling) / ECO (Energy-saving)
• Battery Protect: H, M, L (for reference)
• USB: 5V/1A

Power Supply: Connect to DC 12V/24V or AC 100-240V (using dedicated adapter).

Display Screen Initialization: Connect to power; the buzzer will sound briefly, and the display will be on for 2 seconds to enter normal operating mode.

Power On/Off: Press [Power] to switch ON/OFF.

Temperature Setting: Press + or - for temperature setting. The setting will be saved automatically after stopping for 3 seconds. (Note: The displayed temperature is the current temperature of the compartment; it will take a while to reach the set temperature.) Temperature range: -20°C to +20°C (-4°F to +68°F).

Cooling Mode: Under the running state, press [Mode] to switch between MAX (fast cooling) and ECO (energy-saving).

Battery Protection Mode: Under the running state, long press [Mode] for three seconds until screen flashes, then press [Mode] again to select protection mode H (High), M (Medium), or L (Low). (*Factory setting is H).

Voltage Reference:

*The voltage is theoretical value, there may be a deviation in different scenarios. H should be set when the product is connected to car power, and M or L should be set when it is connected to a portable battery or other back-up battery.

Temperature Unit Setting: Switch off the fridge, long press [Mode] for three seconds until E1 displays, then switch to E5 by pressing [Mode] again. Under E5 mode, press [+] or [-] to select Celsius or Fahrenheit. (*Factory setting is °C).

Reset: Switch off the fridge, long press [Mode] for three seconds until E1 displays, then under E1 mode, long press [+] and [-] at the same time for three seconds to reset it.

Recommended temperature for common food:

7. Care and Maintenance

Cleaning:

• Switch off and unplug the device first to avoid electric shock.
• Use a wet cloth to clean the device and dry it.
• Do not soak the fridge in water and do not wash it directly.
• Do not use abrasive cleaning agents during cleaning as these can damage the device.

A diagram shows cleaning supplies: a bucket, a cloth, and a brush, with a cross over the brush, indicating not to use abrasive tools.

Storage:

• If the device will not be in use for a long time, please follow the instructions:
• Switch off and unplug the device.
• Take out all the items stored in the device.
• Wipe off excess water with a soft rag.
• Put the fridge in a cool and dry place.
• Leave the lid slightly open to prevent odors from forming.
• Recommended storage environment: ambient temperature: 25°C, ambient humidity: ≤ 75%.

Defrosting:

• Humidity can form frost in the interior of the cooling device or on the evaporator. This reduces the cooling capacity. Defrost the device in good time to avoid this.
• Switch off and unplug the device first to avoid electric shock.
• Take out all the items stored in the device.
• Keep the lid open.
• Wipe off the defrosted water.

Never use hard or pointed tools to remove ice or to loosen objects which have frozen in place.

8. Troubleshooting

The refrigerator kept working after reaching the set temperature: It is a normal phenomenon. In order to keep the temperature at the set temperature, the compressor will operate at low power.

Bluetooth connection unavailable: The connection is not correct. 1. When using Bluetooth mode for the first time, it can only be used after the 2.4G Wi-Fi network is connected successfully. 2. After the Wi-Fi connection is disconnected, wait about 2-3 minutes before you can directly use the Bluetooth control.

9. Technical Information

*Due to product improvement, the technical information might be different from actual information, please refer to the rating label on the product.

Manufacturer: Foshan Alpicool Electric Appliance Co., LTD.

Address: 13A Xinlong Road Shiongliyue industrial Zone, Xintang Village, Lunjiao Town, Shunde District, Foshan City, Guangdong, China

Contact: Mickey

Tel: +1 (313) 913-7585

E-Mail: info@bodegacooler.com

10. Warranty

Thank you for purchasing BODEGA COOLER product. We sincerely hope that you are satisfied with the product.

We'd like to offer you 12-month warranty for free. Once activated, your warranty ensures that if anything goes wrong with your product, replacement units/parts will be warranted during the warranty period.

What you need to do:

For any help or questions during use, please contact us via website www.bodegacooler.com, or send email to info@bodegacooler.com. We will service you within 24 hours.

When contacting us, we suggest to send Order ID, a photo or a video for helping us much clearer about the problem and offer you the best solution.