Wireless LED Lighting Film & Event by Astera
User Manual for ASTERA models including: AX2, X55AX2, AX2-100 PixelBar, AX2-50 PixelBar Wireless Linear Wash Fixture, AX2-50 PixelBar Wireless Linear Wash Fixture
Astera LED-Technology GmbH AX2 Pixel Bar X55AX2 X55AX2 ax2
Manual de instrucciones / Manuel d‘instructions / Manual de instruções Model No: PixelBar AX2-50 / AX2-100 --- Manual Version: 1.0 --- Date of Issue: 09/17/20 ... you pass/ rent/ sell the unit to another user. Keep in mind that this manual cannot address all possi-ble dangers and environments. Please use your own caution when operating.
File Info : application/pdf, 4 Pages, 4.80MB
DocumentDocument50 100 AX2 PIXELBAR AX2 PIXELBAR Users Manual / Gebrauchsanleitung / Manuale di istruzioni / Manual de instrucciones / Manuel d`instructions / Manual de instruções Model No: PixelBar AX2-50 / AX2-100 --- Manual Version: 1.0 --- Date of Issue: 09/17/20 // English 2-6 // Deutsch 7-11 // Italiano 12-16 // // Espanol 17-21 // Francais 22-26 // Português 27-31 // Astera LED Technology GmbH Stahlgruberring 36 81829 Munich Germany info@astera-led.com | www.astera-led.com English SAFETY INFORMATION Before you operate this unit read the manual carefully. Always make sure to include the manual if you pass/ rent/ sell the unit to another user. Keep in mind that this manual cannot address all possible dangers and environments. Please use your own caution when operating. This product is for professional use only. It is not for household use. · Do not operate the unit in areas of high temperature conditions or under direct sunlight. It will cause abnormal function or damage the product. · Always use a suitable safety wire when mounting the light overhead. · Connect the safety wire only to the intended safety mount. · Always follow local safety requirements. · Only authorized personal may service the battery. · Do not place in fire or heat. · Do not use or charge the light if it is damaged. · Avoid bumping or plunging, it may cause fire or explosion. · Never store the battery when fully drained. Always recharge immediately when empty. · Make sure to fully charge all units before storing them. · Partially charged batteries will lose capacity. · Fully recharge every 6 months if not used. · The battery may only be replaced with an original spare part from Astera. · Always charge with the flight case open. · It is recommended to charge at a temperature between 15°C and 35°C Warning: In extreme cases, abuse or misuse of standard/rechargeable batteries can lead to: · Explosion · Fire development · Heat generation or Smoke and gas development. Do not directly look into the light. · lt can cause harm to your eyes. · Do not look at the LEDs with a magnifying glass or any other optical instrument that may concentrate the light output. · Use only Astera approved accessories to diffuse or modify the light beam. The exterior surfaces of the light can become hot during normal operation. · Ensure that accidental physical contact with the device is impossible. · lnstall only in ventilated locations. · Do not cover the light. · Allow all lights to cool before touching. · Keep 0.3m (12in) from objects to be illuminated. SECONDARY PROTECTION The AX2-50/-100 PixelBar must always be secured by a safety wire when used in a hanging position. If the primary suspension fails, the device must not fall more than 20cm. Use Safety rigging point. Please check the safety regulations in your region. INTRODUCTION/INTENDED USE The AX2-50 / AX2-100 from ASTERA is a LED wallwasher for professional use in the event and film business. The AX2 is designed for direct or indirect illumination of objects. Due to its built-in battery it can be quickly set up and at places where traditional lights cannot be mounted easily. Like the ASTERA Tubes, the AX2 has the Titan LED Engine and offers excellent color and light values. The AX2 generates white or colored light and the color temperature can be adjusted in many ways. Both AX2 models can be controlled with the AsteraApp or with wired DMX or wireless CRMX. The device can also be controlled by the integrated display or by infrared remote control. The AX2 can be used standing or hanging. For this purpose, the device is equiped with airline tracks to attach the appropriate mounting accessories. Furthermore, several AX2 can be easily connected with the integrated BarConnect+. The AX2 can be used indoors and outdoors and has an IP65 rating. Do not shake the device. Avoid brute force when installing or operating the device. When choosing the installation-spot, please make sure that the device is not exposed to extreme heat or dust. Avoid direct sunlight for a longer period of time. There should not be any cables lying around. You endanger your own and the safety of others! The ambient temperature must be set. Keep away from direct insulation (particularly in cars) and heaters. Never use the device during thunderstorms connected to the power mains. Over voltage could destroy the device. Always disconnect the device during thunderstorms. Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture. Always fix the fixture with an appropriate safety wire. Operate the device only after having become familiarized with its functions. Please consider that unauthorized modifications on the device are forbidden due to safety reasons! If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, crash etc. This device is not for household use and is not suitable for permanent installation. CONTENT #1 AX2-50 or AX2-100 PixelBar #2 Feet (2x ) #3 PowerCON TRUE1 Cable #4 Manual TRANSPORTATION AND STORAGE The AX2-50/-100 PixelBar contains a Lithium Ion battery and can be carried around. A transportation case is recommended to keep the product safe. · Do not place in fire or heat. · Never store the battery when fully drained. · Make sure to fully charge all units before storing them. 2 or #1 #2 #3 #4 3 CLEANING AND MAINTAINING Caution: Liquids entering the housing of the device can cause a short circuit and damage the electronics. Do not use any cleaning agents or solvents. PRODUCT OVERVIEW USING THE AX2 PIXELBAR 1. Control options - integrated control panel Use the menu buttons ( menu, +, - ,enter ) to navigate through the main menu. Settings for color adjustment and brightness / runtime are directly accessible by two symbol buttons. www.astera-led.com When at top Navigation: When inside Main Menu: ON/OFF Enter Main Menu Back to previous Menu Reset Settings Scroll down Change Input Select Scroll up Set DMX Address Choose / Confirm Color adjustment Brightness intensity and runtime control 2. More control options IR On/Off, Static Colors, Preprogrammed Effects APP Settings, Complex effects, Talkback DMX Control from DMX consoles via CRMX or W-DMX DMX Control from DMX consoles via DMX cable 4 3. Switching ON or OFF 1s ON 1x OFF Please not: a new AX2-50/-100 needs a few seconds of charge to disable its shipping mode. 4. Pairing with the AsteraApp Turn the AX2-50/-100 into ,,blue mode" by holding down the power button for 3 seconds. 1x 1x 5. Linking to a CRMX transmitter 1. AX2 PixelBar 2. AX2 PixelBar ENTER 3. AsteraBox 4. AsteraBox *click* + 10 sec WAIT 6. Charging While the power cable is connected, the display shows the charging status. Charge immediately when the battery is empty. Do not store the unit when the battery is empty. Charging time is approximately 5 hours. 5 7. Hanging The Airline tracks at back and bottom of the AX2-50/-100 housing are used to attach optionally available mounting fittings. The AX2-50/-100 can be mounted using TrackPins (AX-TP) and Superclamps/GripHeads or hung up using the TrackHangers (AX-TH) or FlyBar (AX2-FB) for vertical position. When hanging, secure with a safety wire. This should be attached to the safety hooks at the back of the AX2-50/-100 housing. Make sure the light cannot drop more that 20cm if primary mounting fails. BarConnect+ (Integrated fasteners and counterparts) at both ends of the housing click into place and make a form-fitting locked connection when arranging multiple units in a line. When hanging vertical, it is permitted to join a maximum amount of 4 units of AX2-50 or 4 units of AX2-100 together in a line (Notice: fasten at least at every 2nd connection point) 8. Connecting several AX2 with BarConnect+ Quickly merge several PixelBars while maintaining the pixel pitch. Aim connected units together to maintain consistent lighting or hang them. The integrated IR modules enable auto-addressing for AsteraApp and DMX control. 1. 2. 3. *Click* Hang with TrackHanger Hang with FlyBar TROUBLESHOOTING Problem Possible cause The fixture does not turn on The battery may be empty Solution Connect it to the AC and try again Permitted way hanging/saving several AX2 Mount with TrackPin The fixture turns on and the The fixture could be set to display is on, but the LEDs do BLACKOUT mode not emit light Set to display black color or is operating in DMX mode and doesn't receive a valid signal. It is good practice to do a RESET SETTINGS The fixture is not working The fixture may still be opera- It is good practice to do a RESET SETTINGS bet- correctly - it does not display ting under a previous setting ween setups the color or effect chosen The power cable is connected but the fixture is not charging The battery may be fully charged The fixture will only commence charging when its battery has a temperature of 45° C or less. Turn the fixture off and let it cool down; once cold enough, it will start charging Permitted way hanging/saving several AX2 6 SPECIFICATIONS - TECHNICAL DATA Item Code Colors Total LED Power Power Draw Light output - 2700k, 3200k,5500k (50)* Light output - 2700k, 3200k,5500k (100)* CRI(RA)/TLCI 3200-6500k* Beam Angle Strobe Pixels Battery Lifetime Battery Runtime Charging Time (nominal) AX2-50 / -100 RGBMintAmber 80W / 160W 40W / 80W 1800lm, 2230lm, 2265lm 3600lm, 4460lm, 4530lm 96 21° 0 - 25Hz 8 / 16 70 % after 300 cycles up to 20 hours 5 hrs Input Voltage Input Current Range Wired DMX CRMX Receiver Wireless Frequencies Housing IP Rating Operating Temperature Weight Dimensions with hook (mm/inches) Dimensions without hook (mm/inches) 110 - 240V, 50/60 Hz 0.7A/115VAC ~ 1.0A/230VAC 300 m / 330 yds Yes Built in CRMX 2.4GHz, UHF Aluminium IP65 0° - 40° C / 32° - 104° F 4.5kg/9.9lbs / 7.9 kg/17.5 lbs 520 x 165 x 65 / 20.5 x 6,5 x 2,6 1020 x 165 x 65 / 40.1 x 6,5 x 2,6 500 x 165 x 65 / 19.7 x 6.5 x 2.6 1000 x 165 x 65 / 39.4 x 6.5 x 2.6 7