Dash Cam User Manual
Product Appearance
Detailed description of the dash cam components:
- GPS mount
- Rear camera
- Camera lens
- Power indicator light
- Up button
- Power button
- Down button
- Screen
- SD card slot
- MIC
- Loudspeaker
Packing List
Upon opening the package, please check if the dash cam is in good condition and if all accessories are included:
- Main unit x 1
- Electrostatic film x 2
- USB power cord x1
- User manual x1
- Installation pry bar x 1
- Car charger x1
- Rear camera x 1
- TF card x1 (optional)
Installation
1) Install the electrostatic film
Install the electrostatic film on the front windshield in the recommended area (dashed area) shown in the diagram. Before installation, clean the glass and ensure there are no bubbles between the electrostatic film and the glass.
Diagram description: A view of a car's interior dashboard and windshield. An arrow indicates where to paste the electrostatic film on the dotted line frame on the windshield.
Tip: Install the dash cam as close to the middle area above the front windshield as possible to ensure full coverage of the car's front view and improve ADAS-assisted driving accuracy.
2) Attach the dash cam
Remove the 3M adhesive protective film, attach the dash cam bracket to the electrostatic film, and adjust the dash cam to the appropriate angle.
Diagram description: A drawing of the dash cam unit mounted on its bracket, viewed from the front-left side.
3) Wiring and installation of the rear camera
Arrange the rear camera cable from the front windshield to the rear windshield, as shown in the picture below.
Diagram description: A side view of a car, showing the rear camera mounted on the rear windshield and the cable routed along the roofline towards the front.
4) Wiring and connecting the power supply
Route the power cord along the top of the front windshield, through the A-pillar, and into the storage compartment located at the front passenger seat, close to the cigarette lighter port, as shown in the diagram below. Then, connect the power cord to the cigarette lighter power supply.
Tip: Use the included wiring pry bar to bury the power cord under the A-pillar sealant strip. Note that the position of the cigarette lighter port may vary between vehicles, and the pictures are for reference only.
Diagram description: A view of a car's interior dashboard and windshield, illustrating the routing of the power cord along the top of the windshield and down the A-pillar towards the cigarette lighter port.
ADAS Calibration Guide
To ensure the accuracy of ADAS, it is essential to perform ADAS calibration before use.
After wiring, the dashcam powers on and starts recording. Upon first power-up, ADAS calibration is required. Follow the steps shown in the diagram for adjustment. (If not the first power-up, navigate to ADAS calibration in the driving assistance section within the settings menu.)
- Adjust the installation position of the dashcam to align the vertical line of ADAS calibration with the centerline of the vehicle as much as possible.
- Adjust the camera angle to align the horizontal line with the horizon of the road (the plane where the road meets the distance).
- After calibration is complete, ADAS will become effective. For detailed ADAS function triggering conditions and alert content, refer to the electronic manual.
Diagram description: A view from the dash cam's perspective, showing a road ahead. A vertical line is shown aligned with the center of the car's lane, and a horizontal line is shown aligned with the horizon.
ADAS functions provide information and cannot replace driver observation. Comply with traffic regulations and take responsibility for safe driving judgment. This function relies on recorder warnings and may be limited under low visibility conditions.
Download and Installation of the App
Method 1: Scan the QR code provided below to download and install the app.
Method 2: Search for "botslab" in major application stores and click Download to install the botslab app.
Diagram description: A QR code labeled "Scan to download Botslab APP".
User Guide
Scan the QR code to access the online version of Quick Start Guide and obtain more detailed instructions on how to use the dash cam.
Diagram description: A QR code labeled "User Guide".
Precautions for Using the Dash Cam
- This product is an auxiliary device (dash cam) for safe driving.
- Any losses resulting from product malfunctions, data loss, or product usage are not the responsibility of the company.
- This product is designed to record external images of vehicles. Due to different driving and vehicle environments, some functions may not be supported.
- Firmware upgrades may periodically improve the product, potentially causing changes in performance or inability to capture images due to the usage environment. Driving images are for reference only.
- While the product records accident images, it does not guarantee all accident images are recorded. Minor collisions may not activate the collision sensor, so images may not be recorded in a dedicated folder.
- Do not install or operate this product while the vehicle is in motion.
- This product must be directly connected to the car's power supply system and installed by professionals with installation experience. Do not use this product for a long time without starting the engine.
- This device may interfere with the function of improperly protected medical devices. Seek advice from a doctor or medical device manufacturer if uncertain about RF energy shielding.
- Do not subject this product to strong shocks or vibrations.
- Before cleaning or maintenance, stop using the product.
- Do not use chemical solvents or cleaning agents.
- Do not disassemble or modify the product without authorization.
- Normal operating temperature: 0°C to 50°C.
- Ensure use within legal limits.
Important Statement
Personal Information Security
To ensure safety, ensure the product is bound only by authorized persons. Botslab Inc. will take strict measures to ensure the security of your and your family's information.
FCC Regulatory Conformance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
Attentions And After-Sales Service
I. Introduction and declaration of after-sales service
- Thank you for choosing the dash cam. Use only manufacturer-provided accessories to avoid malfunctions or damage. Failure to use the product as outlined, or connecting incompatible accessories, voids the warranty. The company assumes no responsibility for danger or damage from unauthorized uses. Dismantling or changing the product housing also invalidates the warranty.
- Botslab Inc. is committed to constant improvement and sustainable development. Product manuals may be modified without advance notice.
- Unless specified by applicable laws, manual contents are based on manufacturing conditions. No explicit or tacit warranty is made for correctness, reliability, or contents.
- The product manual is protected by copyright law. Copying, transmitting, distributing, or using it in other forms is forbidden without written approval.
II. Service policies within the warranty period
- This product has a one-year warranty. Contact local authorized distributors for details.
- The warranty period for the power adapter and charger cable is 12 months, and for the battery, it is 6 months.
- Non-electronic accessories are not covered by the warranty.
This symbol indicates that the product should not be disposed of as regular household waste. It must be taken to an appropriate collection facility for recycling to protect natural resources, human health, and the environment.
List of Performance Faults of Dash Cam
| Name | Performance Fault |
|---|---|
| Mainframe of 360 dash cam | Failure of functions listed in the product manual; No display or incorrect characters on screen; Failure during start-up or normal recording; Button control failure; Cracks in housing due to structural or material issues. |
| Charger & charger cable | Abnormal status or operation, or failure to charge properly with the designated charger. |
III. Charged maintenance policies
If any of the following cases occur, the company or its authorized service centers will provide reasonable maintenance services at a cost for those outside the scope of the warranty:
- Exceeding the valid warranty period.
- Lack of warranty certificate or valid invoice. The warranty certificate does not match the model and labeling of the product, or has been tampered with.
- Damage caused by usage, repair, and maintenance that does not follow the User Manual requirements. Damage or malfunction resulting from personal removal, maintenance, or modification of system software without authorization from the Company.
- Collision, soaking, breaking, or burning of the printed circuit board.
- Cracking or damage to the outer shell, LCD screen, antenna, etc., during use, except for that caused by structural or material factors.
- Damage due to force majeure.
Contact Us
- Website: https://www.botslab.com
- Email: service@botslab.com
- Facebook: @botslabofficial
RF Exposure
CE
EU regulatory conformance:
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of 20cm between the device and the human body. To comply with RF exposure requirements, it is recommended to use the product while maintaining a distance of 20cm between the device and the human body.
CE DOC
Botslab Inc. declares that the radio equipment type G580H-N560-1 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.botslab.com
Manufacturer Information
Company name: Botslab Inc.
Address: 919 North Market Street, Suite 950, Wilmington, New Castle, Delaware, USA
Operation temperature: 0~50℃
Operation frequency (Max power):
- Wifi: 2412MHz-2472MHz (<20dBm)
- Bluetooth: 2402MHz-2480MHz (<13dBm)
FCC
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Responsible party (contact for FCC matters only):
Botslab Inc.
919 North Market Street, Suite 950, Wilmington, New Castle, Delaware
