Owner's Manual for formlabs models including: V1 FLRGWH01, Rigid 4000 Resin, 4000 Resin, Resin
Technische Spezifikationen der SLA-3D-Drucker von Formlabs im Vergleich | Formlabs
Best-in-class 3D Printers | Formlabs
ENGINEERING RESIN Rigid 4000 Resin Resin for Stiff, Strong, Engineering-Grade Prototypes Glass-filled Rigid 4000 Resin prints with a smooth, polished finish and is ideal for stiff and strong parts that can withstand minimal deflection. Consider Rigid 4000 Resin for general loadbearing applications. Mounts and brackets Thin-walled parts Jigs and fixtures Simulates stiffness of PEEK V1 FLRGWH01 Prepared 10/07/2020 Rev. 01 10/07/2020 1 To the best of our knowledge the information contained herein is accurate. However, Formlabs, Inc. makes no warranty, expressed or implied, regarding the accuracy of these results to be obtained from the use thereof. Material Properties Tensile Properties Ultimate Tensile Strength Tensile Modulus Elongation at Break Flexural Properties Flexural Stress at 5% Strain Flexural Modulus Impact Properties Notched Izod Thermal Properties Heat Deflection Temp. @ 1.8 MPa Heat Deflection Temp. @ 0.45 MPa Thermal Expansion (0-150 °C) METRIC 1 Green 2 Post-Cured 3 METRIC 1 33 MPa 69 MPa 2.1 GPa 4.1 GPa 23% 5.3% METRIC 1 43 MPa 105 MPa 1.4 GPa 3.4 GPa METRIC 1 16 J/m 23 J/m METRIC 1 41 °C 60 °C IMPERIAL 1 Green 2 Post-Cured 3 IMPERIAL 1 4786 psi 10007 psi 305 ksi 595 ksi 23% 5.3% IMPERIAL 1 6236 psi 15229 psi 203 ksi 493 ksi IMPERIAL 1 0.3 ft-lb/in 0.43 ft-lb/in IMPERIAL 1 105 °F 140 °F 48 °C 77 °C 64 m/m/°C 63 m/m/°C 118 °F 36 in/in/°F 170 °F 35 in/in/°F METHOD METHOD ASTM D638-14 ASTM D638-14 ASTM D638-14 METHOD ASTM D790-15 ASTM D790-15 METHOD ASTM D256-10 METHOD ASTM D648-16 ASTM D648-16 ASTM E831-13 SOLVENT COMPATIBILITY Percent weight gain over 24 hours for a printed and post-cured 1 x 1 x 1 cm cube immersed in respective solvent: Solvent Acetic Acid 5% Acetone Isopropyl Alcohol Bleach ~5% NaOCl Butyl Acetate Diesel Fuel Diethyl glycol Monomethyl Ether Hydraulic Oil Skydrol 5 Hydrogen peroxide (3%) 24 hr weight gain, % 0.8 3.3 0.4 0.7 < 0.1 < 0.1 1.4 0.2 1.1 0.9 Solvent Isooctane (aka gasoline) Mineral oil (light) Mineral oil (Heavy) Salt Water (3.5% NaCl) Sodium Hydroxide solution (0.025% PH 10) Water Xylene Strong Acid (HCl conc) 24 hr weight gain, % < 0.1 0.2 0.2 0.7 0.7 0.7 < 0.1 5.3 1 Material properties can vary with part geometry, print orientation, print settings, and temperature. 2 Data was obtained from green parts, printed using Form 3, 100 m, Rigid settings, without additional treatments. 3 Data was obtained from parts printed using Form 3, 100 m, Rigid settings and post-cured with a Form Cure for 15 minutes at 80 °C. 2Adobe PDF Library 17.0 Adobe InDesign 20.0 (Macintosh)