CREALITY LD-006 3D Printer User Manual

User Manual for CREALITY models including: LD-006 3D Printer, LD-006, 3D Printer, Printer

LD-006 说明书-中英-7-21

Download

LD-006 Software& Firmware Download - Creality 3D Printer

3D Printer User Manual

File Info : application/pdf, 24 Pages, 14.97MB

ae951808b69614ef0daca0949019b5af

3D Printer User Manual
3D
LD-006
V1.0

Content
Dear Consumers, Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our teams will always be ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our product, you can also learn how to use the Printer in the following ways: View the accompanied instructions and videos in the U disk. Visit our official website www.creality.com to find relevant software/hardware information, contact details and operation and maintenance instructions.
U www.cxsw3d.com

Notes

Assemble the 3D Printer

Use the 3D Printer

Level the Platform

Load Resin

Release Film Instructions

Start Printing

Clean the Resin Vat

NOTES
1. Do not use the printer any way other than described herein in order to avoid personal injury or property damage. 2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment. 3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality. 4. Please use recommended resin to in case damage of machine. 5. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet. 6. Please do not open the plastic cover during usage, otherwise the printing will be interrupted. 7. Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage. 8. Please wait a moment after the print is finished. And please wear gloves to take out the model by tools. 9. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface. 10. Children under 10 years should not use the printer without supervision. 11. TipsDo not plug or unplug the power cord when power on. 12. Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators' legal liability under any circustance.
1 2 3 4 5 6 7 8 9 1010 11 12

Equipment Introduction

1 2
3 4
5
1 Leveling screw
2 Buliding platform
3 Thumb screw
4 Resin vat
2

6
7 10
9 8

5 Touch screen
6 Limit sensor conductor
7 Air filter
8 Power switch

9 Power socket
10 USB port USB

Equipment Parameters

Package Content

1 U disk x 1 U
5 Resin filter x 4

Tool list

2 Screwdrivers x 1set

3 Brush x 1

6 Release film x 1

7 Metal blade x 1

9 Vat cover x 1

Calibration Card

10 Calibration card x 1

Tips: the above accessories are for reference only, in kind prevail!

4 Plastic blade x 1
8 Power cord x 1

1 Assemble the 3D Printer 3D 2
1
1 Machine body x 1

2 Plastic cover x 1

Note: Put the plastic cover on the machine body and the installation is completed.
5

Interface Information

Tools

Note: The UI information is only for reference, the actual UI may be different. UI 6

Z : 0.10mm 1.00mm 10.00mm10mm

1 Home 4 Stop

2 Up 3 Down 5 Back

0.10mm 1.00mm 10.00mm

1 2 3

Interface Information

System

Note: The UI information is only for reference, the actual UI may be different. UI

LD-006
004c0026-554d5002-20363643-17f V4.3.17_LCDMI/3840x2400/F2.18
LD-006
004c0026-554d5002-20363643-17f V4.3.17_LCDMI/3840x2400/F2.18
7

Interface Information

.ctb .ctb

.ctb

1 Refresh file 2 Turn up 3 Turn down 4 Back

.ctb .ctb

.ctb

1 2 3 4
Note: The UI information is only for reference, the actual UI may be different. UI 8

.ctb

1 Delete 2 Print/stop 3 Back
.ctb

1 2 / 3

3 Level Platform 1 1

1. First raise the platform, then loosen rubber screws on the left and right sides of the resin vat, and take out the resin vat.

2. Place the calibracation card on the printing screen go " Tools Manual Home"with the touch screen, and check whether the platform sticks into thecalibration card evenly.

Note: The printing platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to adjust the printing platform.

Level Platform 2 2
If the platform does not stick to the print screen, do as the following:

Z : 0.10mm 1.00mm 10.00mm 10mm

1. After unscrewing the leveling screws, press"Home" to keep the platform and the print screen parallel.

2. Gently press the platform and tighten 4 screws clockwise, and the platform can be leveled successfully.

Z : 0.10mm 1.00mm 10.1000mmmm

3. Move up the z-axis to a proper position, remove the calibration card and install the resin vat back, and then tighten the fixing screws at both ends of the resin vat. 10

Level Platform 2 2
If the platform does not stick to the print screen, do as the following:
0.10mm 1.00mm 10.00mm

1. ""

2. 4

0.10mm 1.00mm 10.00mm

3 . Z 11

Load Resin
Pour the UV photosensitive resin into the resin vat. The slot capacity is 500ml/1000ml.

3D UV 500ml/1000ml

Please pay attention to the orientation marks and keep the printing platform assembled in the right direction. Otherwise it may lead to leveling faliure!
1000ml
500ml

TipsHow to change resin: Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin, and then install the resin vat to the machine.

Caution Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use to avoid direct contact with the skin. ,

6 Release Film Instructions
Installation steps

a. First, remove the 14 screws at the bottom of the vat and take

down the old release film.

14,

b. Prepare the new release film, peel off the the protective films on both sides of the release film. Align the holes and fit the release film on the clamping ring.
b. c. Finally, place the film-ring assembly back into the vat frame gently, then intall and tighten the fixing screws diagonally. 14
d. The installed release film is as shown.

Parameters
190mm*266mm (Size)
0.15-0.2mm (Thickness)
95% (Light Transmittance )

7 Start Printing

1. Slice

ctb(.ctb)

1. Open the slice software of LCD 3D printer, click"open"on the left of the screen and add model file.

5è

æ
1.-Eiffel Tower.ctb 1.-Eiffel Tower.ctb
ç

2. If the model needs to add support, click the upper right icon to set corresponding parameters.
1.-Eiffel Tower.ctb

3. Click icon click "Setting"setting slice parameters

4. Click"Slice"waiting for slice to be finishedsave the

( recommend to set parameters of bottom layer as 5-20).

sliced file( You are welcome to find more details of slicing

tutorial on the official website www.creality.com).

Start Printing

æ
1.

ctb(.ctb) ctb(.ctb)

1. LCD3d"" 2.

.ctb
è 5

æ
1.-Eiffel Tower.ctb .ctb
ç

.ctb .ctb

3. 5-20 4. *www.cxsw3d.com)
15

Start Printing

.ctb .ctb
2. Print
1. Generate CTB fileand save the file to U disk.

USB port 2. Insert the U disk press the print button.

.ctb
2.
1. CTBU 16

.ctb
U 2. U

Start Printing

.ctb .ctb

3. Press"up"or"down"to select files.

.ctb

40%

Eiffel Tower 8S.c.cttbb

00h40m

1h00m

972/2430

4. Select the file to be printed and press"print".

5. Printing.

.ctb .ctb

.ctb
4.

40%

_ 8S.ctb .ctb

00h40m

1h00m

972/2430

Clean the Resin Vat

Please confirm that the printing platform has been removed, and there are moderate consumables in the vat. Please set the exposure time of the test image:
15 s
Next

*If there is residue in resin vat before printing, please clean resin vat first. The cleaning time is generally set to 15 seconds and then shovel it off with a plastic blade.

*15s, 18

15 s

Wiring Connection

Z endstop(minimum position) Z endstop(maximum position) Z motor

Mainboard fan port UV LED fan port

UV LED port

Power supply

Z LED LED

Ethernet port

USB 2.0 port USB 2.0

LCD resin panel

TFT resistive touch screen Z motor driver pin

External motor driver pin

mipi

Z EXT

Troubleshooting

Workflow
Start By memory card print

Fault diagnosis N

Fault cause U-disk

Y/N

N File identified

or not

Return home

Other files can be printed normally or not

Slice

Axis motor

Y/N

Work or not

Exceed the home

Stick to the printing screen

Y/N Y
The screen is on

N N

Wire

Y/N

connection

Z-axis motor Y Z motor rotates

or not

Finish

Limit switch Leveling
Coupler Z-axis motor

Fault handling 1. Wipe U disk . Format U disk . Replace U disk
Move model position and slice again .Use the repair software to repair model.
Reconnect circuit . Check by substitution Reconnect circuit . Check by substitution
Leveling operation
Reconnect circuit
Replace screen
Fasten coupler
Reconnect circuit . Check by substitution

Result feedback

Process result

Problem solved
Component damage, replace continuously
Unknown malfunction, please contact the after-sales

. .
. . .

Scan To Learn More

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.
Add:18F,JinXiuHongDu Building, Meilong Blvd., Longhua Dist.,
Shenzhen, China 518131 Official Website: www.creality.com Tel+86 755-8523 4565 E-mail: info@creality.com cs@creality.com

18F www.cxsw3d.com 400 6133 882 0755-8523 4565

References

Adobe PDF library 15.00