Important Information
Before starting, compare items on your invoice with items received. Thoroughly check packing materials. If an item is missing, please call Crutchfield at 1-888-955-6000.
Step 1 -- Match & Connect Wires
A. Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
B. Some wire functions depend upon what vehicle the harness is being applied to. See the chart on the next page as a guide for your particular vehicle before making any connections.
C. Individually tape off any unused wires.
D. Refer to the chart on page 3 for the amplifier location in your vehicle, and make final wiring connections following instructions on page 4.
Wire Color Guide:
Red - 12 Volts Switched Power
Blue - Power Antenna
Black - Chassis Ground
Yellow - 12 Volts Constant Power
Green/Red - (see next page)
Dark Blue/Pink - (see next page)
Green/Black - Left Rear Speaker Negative
Violet/Black - Right Rear Speaker Negative
White/Black - Left Front Speaker Negative
Gray/Black - Right Front Speaker Negative
White/Red - (see next page)
Brown/Blue - (see next page)
Green/Orange - (see next page)
Brown/White - (see next page)
Green - Left Rear Speaker Positive
Violet - Right Rear Speaker Positive
White - Left Front Speaker Positive
Gray - Right Front Speaker Positive
Green/White - (see next page)
Yellow/Brown - (see next page)
Step 1 -- Match & Connect Wires -- Continued
| Wire Color | Vehicle/Function | Vehicle/Function | Vehicle/Function | Vehicle/Function |
|---|---|---|---|---|
| Green/Red | 4Runner, Sienna - Rear Tweeters Negative | Matrix, Solara Convertible, Tacoma - Sub Coil 2 Negative | Sequoia, Solara Coupe - Left Front Tweeter Negative | Prius, Tundra - Not Used (tape off) |
| Dark Blue/Pink | 4Runner, Prius, Sienna - Center Speaker Negative | Matrix, Solara Convertible, Tacoma - Sub Coil 1 Negative | Sequoia, Solara Coupe - Right Front Tweeter Negative | Tundra - Not Used (tape off) |
| White/Red | 4Runner - Subwoofer Coil 1 Negative | Matrix, Prius, Tundra - Left Front Door Woofer Negative (The White/Black wire is for the Left Front Tweeter Negative) | Sienna - Subwoofer Coil 2 Negative | Sequoia, Solara, Tacoma - Not Used (tape off) |
| Brown/Blue | 4Runner - Subwoofer Coil 2 Negative | Matrix, Prius, Tundra - Right Front Door Woofer Negative (The Gray/Black wire is for the Right Front Tweeter Negative) | Sienna - Subwoofer Coil 1 Negative | Sequoia - Not Used (tape off) |
| Green/Orange | 4Runner, Sienna - Rear Tweeters Positive | Matrix, Solara Convertible, Tacoma - Sub Coil 2 Positive | Sequoia, Solara Coupe - Left Front Tweeter Positive | Prius, Tundra - Not Used (tape off) |
| Brown/White | 4Runner, Prius, Sienna - Center Speaker Positive | Matrix, Solara Convertible, Tacoma - Sub Coil 1 Positive | Sequoia, Solara Coupe - Right Front Tweeter Positive | Tundra - Not Used (tape off) |
| Green/White | 4Runner - Subwoofer Coil 1 Positive | Matrix, Prius, Tundra - Left Front Door Woofer Positive (The White wire is for the Left Front Tweeter Positive) | Sienna - Subwoofer Coil 2 Positive | Sequoia, Solara, Tacoma - Not Used (tape off) |
| Yellow/Brown | 4Runner - Subwoofer Coil 2 Positive | Matrix, Prius, Tundra - Right Front Door Woofer Positive (The Gray wire is for the Right Front Tweeter Positive) | Sienna - Subwoofer Coil 1 Positive | Sequoia, Solara, Tacoma - Not Used (tape off) |
Vehicle Applications and Amplifier Locations
| Vehicle | Amplifier Location |
|---|---|
| 2003-'06 Toyota 4Runner | Passenger's rear side panel |
| 2005-'06 Toyota Matrix | Under front passenger's seat |
| 2004-'05 Toyota Prius | Under front passenger's seat |
| 2005 Toyota Sequoia | Below and behind radio |
| 2004-'06 Toyota Sienna | Behind glove box |
| 2004 Toyota Camry Solara | Behind glove box |
| 2005-'07 Toyota Tacoma | Behind rear seat on passenger's side |
| 2004-'06 Toyota Tundra | Behind rear seat on driver's side |
Step 2 -- Crimp Connections
Tools & Parts Required: Wire Stripper/Crimp Tool, Crimp Caps
A. Strip wires back 1/2”.
B. Twist wires together and insert in crimp cap.
C. Squeeze middle of cap for tight connection.
Step 2 -- Continued
D. Complete crimp connections for all necessary wires.
E. Be sure to wrap any wires from the Wiring Adaptor that are not necessary (wires with no match from the new receiver) with electrical tape.
[Illustration: Receiver Wiring Adaptor with several wires, one labeled "Unused Wire (tape over bare wires)"]
Step 3 -- Application
When ready to install the receiver, plug the Wiring Adaptor from the new receiver or receiver assembly into the factory radio harness(es) in the vehicle dash.
[Illustration: Generic car dashboard with a car stereo being installed.]
