Aftermarket ATV-UTV Parts and Accessories
Instruction Manual for SUPERATV models including: 2753 Polaris Ranger Kinetic Atlas, 2753, Polaris Ranger Kinetic Atlas, Ranger Kinetic Atlas, Kinetic Atlas, Atlas
Polaris Ranger Kinetic Atlas Pro 1.5 Rear Offset A-Arms
File Info : application/pdf, 7 Pages, 1.03MB
DocumentDocument2753 Michigan Road · Madison, Indiana 47250 · 855-743-3427 INSTALLATION INSTRUCTIONS Rear High Clearance A-Arms: for Polaris Ranger® XP 1000 Do not discard packaging until product has been successfully installed. A (Passenger) B C (Driver) D Item Description A Passenger Upper B Passenger Lower 6 each 4 each C Driver Upper D Driver Lower Liability Statement SuperATV's® products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV's® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together. Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof. Need help with your installation? sales@superatv.com www.superatv.com 1-855-743-3427 © 2022 SuperATV.com®. All Rights Reserved. 8:00am - 8:00pm EST M-Th 8:00am - 7:00pm EST Friday 9:00am - 2:00pm EST Saturday Read instructions and view illustrations before beginning. Thank You For Choosing IN-AA-P-RAN1K-R-OHC 12/14/2022 Components Removal: Keep all components removed from machine. Remove: - Sway Bar Links from A-Arms and Sway Bar - Shocks from A-Arms - Pins, Axle Nuts, and Washers - Hubs and Bearings - A-Arms from Frame (Passenger) (Passenger) IN-AA-P-RAN1K-R-OHC 2 A-Arms Prep: set aside when complete - Install provided Fittings along with stock or SuperATV Bearings and Bushings into A-Arms. 2x - Fitting C D Reuse stock Bushings and Bearings 2x - Fitting (Driver) IN-AA-P-RAN1K-R-OHC 3 PIVOT BLOCK SETTINGS - Place new A-Arms onto a flat surface and verify dimension shown. - Negative 1° camber setting is achieved when Pivot Blocks are set to this dimension. - See last page for additional camber information. * center of Pivot Blocks * center of holes 15-7/8" * Leave Jam Nuts loose. Tighten after final adjustments have been made. IN-AA-P-RAN1K-R-OHC 4 - Install Driver Lower (D) to Frame with stock hardware. - Leave Nuts loose until all final adjustments have been completed. - Install Driver Upper (C) to Frame with stock hardware. Tighten hardware completely; SuperATV recommends using Loc-Tite. - Use a strap and "hang" Driver Upper (C) up and away. C D (Driver Side) - Repeat steps and install passenger side components. - Reinstall Knuckles, Rotors, Shocks, and Sway Bar Links. - Reinstall Tires and check Camber settings; see last page. - Tighten all Nuts; SuperATV recommends using Loc-Tite on Nuts. IN-AA-P-RAN1K-R-OHC 5 - Secure Brake Lines to new A-Arms with provided Brake Line Clips and hardware. 3x Brake Line Clip and hardware (Driver Side) C IN-AA-P-RAN1K-R-OHC 6 CAMBER - Tires must have equal air pressure before making adjustments. - Adjustments to be made after all suspension components have been completely assembled. - Tires must not be in contact with ground when making adjustments. - Perform adjustments in small increments. 0° Positive Camber: tire leans out 0° Negative Camber: tire leans in (Passenger) (Passenger) Adjusting Camber: - Remove A-Arms from Frame and turn Pivot Blocks to adjust camber. Reinstall Arms. - Lower machine and settle suspension components by rolling machine back and forth several feet at a time. - Check settings and make small adjustments as needed. - Each time an adjustment is made, machine must be rolled back and forth to settle suspension components. - Once desired setting is achieved, tighten hardware completely. Loc-tite on Nuts is recommended. A NEGATIVE CAMBER SETTING OF 1° to 2° IS RECOMMENDED. LOWER: Too much positive camber: adjust Pivot Blocks OUT. Too much negative camber: adjust Pivot Blocks IN. note: 2 full turns is 1° UPPER A-ARMS: Too much positive camber: adjust Pivot Blocks IN. Too much negative camber: adjust Pivot Blocks OUT. note: 2 full turns is 1° IN-AA-P-RAN1K-R-OHC 7