Euro Appliances EP900UMS2 Rangehood
Product Code: EP900UMS2
Document Type: Usage and Care Guide
Notice
Thank you for choosing our cooker hood. Please read the instruction manual carefully before use.
The installation work must be undertaken by a qualified and competent fitter.
The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text.
The cooker hood is used on 220/240V, 50Hz.
Contents Included:
- 1x Rangehood
- 1x Packet of Screws
- 1x Operating Instructions
Installation
1. Placement: The cooker hood should be placed at a distance of 65-75cm (26-30inch) from the cooking surface for the best effect.
2. Cupboard Hole: Drill a hole in the cupboard with dimensions 490*265 mm. Ensure it is at least 35mm from the edge of the hole to the cupboard edge.
3. Filter Removal: Take down the filter and remove the 2 (M4 x 10mm) screws on the panel.
4. Mounting: Use the provided accessory screws (ST4 x 18mm) to fix the hood into the cabinet.
5. Panel Attachment: Use 2 screws (M4 x 10mm) to fix the panel into the body and equip the filter.
6. One-Way Valve: Install the one-way valve into the air outlet and secure it.
Diagram Description: Diagram showing the required cutout dimensions for the rangehood installation: 865mm width and 265mm height. Another diagram shows the components of the rangehood during installation, including the main unit, filter, and mounting screws. A third diagram illustrates the recommended installation distance for the rangehood above the cooking surface, showing a height of 65-75cm (26-30 inches).
Use
The control panel features the following functions:
- Stop Button ⏹️: Stops the motor.
- Low Speed Button ?: Runs the motor at low speed.
- Mid Speed Button ??: Runs the motor at mid speed.
- High Speed Button ???: Runs the motor at high speed.
- Light Button ?: Turns the two lights on. Press again to turn them off.
Diagram Description: Control panel icons: Stop button (circle with a line), Low speed fan (one wave symbol), Medium speed fan (two wave symbols), High speed fan (three wave symbols), Light (lightbulb symbol).
Installation Instructions & Warnings
Electrical Connection:
- Connection of the appliance to the supply mains.
- Ensure the appliance can be disconnected from the supply after installation, either via an accessible plug or a switch in the fixed wiring, in accordance with wiring rules.
Warning: Failure to install screws or fixing devices correctly may result in electrical hazards. ⚠️
Notice of Installation:
- Before installation, ensure the area is clean to avoid suction of debris.
- Air must not be discharged into a flue used for exhausting fumes from appliances burning gas or other fuels.
- The ventilation tube should bend at ≥120°, be parallel or above the start point, and connect to the external wall.
- After installation, ensure the extractor is level to prevent grease collection.
Installation Warnings:
- Ensure adequate room ventilation when the range hood is used simultaneously with appliances burning gas or other fuels.
- Comply with regulations concerning air discharge.
Safety Warning
- Never let children operate the machine.
- The cooker hood is for home use only; not suitable for commercial purposes like barbecue or roast shops.
- Please ask a qualified technician for assembly.
- The cooker hood and its filter mesh should be cleaned regularly to maintain good working order.
- Before cleaning, switch off the power at the main supply.
- Clean the cooker hood according to the instruction manual to prevent fire hazards.
- If any fault occurs, contact the service department for a service engineer.
- There is a fire risk if cleaning is not carried out according to instructions.
- Do not flambé under the range hood.
Caution
Accessible parts may become hot when used with cooking appliances. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use by a responsible person. Children should be supervised to ensure they do not play with the appliance. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard. ?
Maintenance
The cooker hood and its filter mesh should be cleaned regularly to keep in good working order. Because the grease filters are made of metal, do not clean the filters with detergents that will corrode metal products.
Filter Cleaning Methods:
- Method One: Place the filter in water (40°C-50°C), add some grease-loosening detergent, soak for 2-3 minutes, then clean with a soft brush. Do not brush too hard to avoid damaging the filter.
- Method Two: Place the filter in a dishwasher with detergent. Set the temperature at around 60°C.
To protect the main body from corrosion, clean it weekly with hot water plus soap or a non-corrosive detergent. Do not use grinding detergent, as it will damage the body.
Keep the motor and other spare parts free from water to prevent damage.
Filter Disassembly and Assembly:
Diagram Description: Diagram illustrating the removal of the rangehood filter.
Activated Carbon Filter & Bulb Replacement
Activated Carbon Filter:
Activated carbon filters can be used to trap odors. To install, unscrew and remove the front panel. Plug the activated carbon filter into the unit and turn it anti-clockwise. Repeat on the other side.
NOTE: Ensure the filter is securely locked. An unlocked filter could cause damage. Attaching an activated carbon filter may lower suction power.
Diagram Description: Diagram showing the cylindrical activated carbon filter and its attachment mechanism within the rangehood.
Bulb Replacement:
To change the bulb, press the lamp cup and take out the bulb by turning it counter-clockwise.
Diagram Description: Diagram depicting the process of replacing the rangehood light bulb, showing the lamp cup and bulb removal.
Abnormity and Solution
Fault | Cause | Solution |
---|---|---|
Light does not work, but motor work | The bulb damaged | Change bulb |
Bulb contact lamp cap bad | Fix or change | |
Light panel switch damage | Fix or change | |
Light work, but motor does not work | Bulb contact lamp cap | Restart later |
Motor bearings damage | Change motor | |
Motor burn out | Change motor | |
Light does not work, motor does not work | Motor control switch damage | Fix or change |
Plug contact outlet bad | Fix or change | |
Power wire cut off | Change power wire | |
Shake of the body | Switch damage | Fix or change |
Wind leaves damage | Change leaves | |
Motor screw loosen | Screw it tight | |
Combination screw loosen | Screw it tight | |
Insufficient suction | Body hang unfixable | Tight the body |
The distance between the body and the gas top too long | Readjust the distance | |
Cross-ventilation too strong or too closed in the kitchen | Reduce cross-ventilation or open the window | |
Exhaust pipe too long | Adjust the length of pipe | |
Air outlet valve not open | Check the valve if flexible | |
The outside wind is too strong | No the technical problem |
Contact Information
Service + Support: 1800 440 335
Email: service@eurostylegroup.com.au
HEAD OFFICE
65 Glynburn Road, Glynde SA 5070
Phone: 08 8165 1012
Website: www.euroappliances.com.au