User Guide for Bespoke models including: 15 Channel Programming Remote Control, Programming Remote Control, Remote Control, Control
Bespoke Room Darkening Roller Shades | Selectblinds
File Info : application/pdf, 6 Pages, 6.56MB
DocumentDocumentGETTING STARTED - continued 7. ADDING A REMOTE CONTROL USING AN EXISTING REMOTE CONTROL a. a. On the current remote Action on Remote control, press one "P2" Control button until motor jogs x1 and beeps x1. Motor b. Once more, on the Response current remote control, press one "P2" button until motor jogs x1 and beeps x1. Action on c. c. On the New remote control, press one "P2" Remote Control button until motor jogs x2 and beeps x3. Motor Response Current Remote Control P2 Jog x1 Beep x1 NEW Remote Control P2 Jog x2 Beep x3 Current Remote Control b. P2 Jog x1 Beep x1 *Repeat the same procedure to add/remove additional remote control. PROGRAMMING A NEW REMOTE CONTROL Follow instructions under the section 1. Pair / Unpair Remote Control 8. ADJUSTING THE MOTOR SPEED INCREASE MOTOR Action on a. P2 b. SPEED Remote Control a. Press one "P2" button until motor jog x1 and beep x1. Motor Response Jog x1 Beep x1 Action on c. b. Press "Up" button until Remote motor jog x1 and beep x1. Control Up c. Once more, press "Up" button until motor jog x2 and beep x1. Motor Response Jog x2 Beep x1 Up Jog x1 Beep x1 *If the motor has no response, it already has a Maximum or Minimum speed. DECREASE MOTOR SPEED a. Press one "P2" button until motor jogs x1 and beeps x1. b. Press "Down" button until motor jogs x1 and beeps x1. c. Once more, press "Down" button until motor jogs x2 and beeps x1. Action on Remote Control a. P2 b. Down Motor Response Jog x1 Beep x1 Action on c. Remote Control Down Motor Response Jog x2 Beep x1 Jog x1 Beep x1 *If the motor has no response, it already has a Maximum or Minimum speed. QUICK INDEX SETTINGS STEPS 1. Pairing P1 (hold for 2s) > Stop (hold for 2s) 2. Switch Rotating Direction Up + Down (hold for 2s) 3. Set Upper/Lower Limits Upper Limit: Up (hold for 2s) > Up + Stop (hold for 2s) Lower Limit: Down (hold for 2s) > Down + Stop (hold for 2s) Add/Remove 4. Favorite Position P2 > Stop > Stop 5. Roller/Sheer Switch Mode Up + Down (hold for 5s) > Stop 6. Adjusting Limits the Upper: Up + Stop (hold for 5s) > Up or Dn > Up + Stop (hold for 2s) Lower: Dn + Stop (hold for 5s) > Up or Dn > Dn + Stop (hold for 2s) 7. Add/Remove Remote a P2 (existing) > P2 (existing) > P2 (new) Increase Motor Speed: P2 > Up > Up 8. Speed Regulation Decrease Motor Speed: P2 > Down > Down TROUBLESHOOTING PROBLEM - THE MOTOR HAS NO RESPONSE Cause Solution Battery in motor is depleted Recharge with compatible AC adapter and check connection and positioning of Insufficient charging from Solar solar panel Check connection and orientation of Panel solar panel Remote control battery is discharged Replace battery or check placement. or not installed properly Radio interference / shielding Ensure remote control and the antenna on the motor are positioned away from metal objects Receiver distance is too far Move the remote control to a closer position. Power failure Check power supply to motor is connected/active. Incorrect wiring Check that wiring is connected correctly. PROBLEM - THE MOTOR BEEPS 10 TIMES WHEN IN USE Cause Battery voltage is low/ Solar Panel Issue Solution Recharge with AC adapter or check connection and positioning of solar panel PROBLEM - THE MOTOR WILL NOT PSRoOluGtRioAnM OR CONNECT Cause Press the P1 button on the motor for 2 Check if the motor in Sleep Mode seconds to activate Pairing Mode. Multiple Motors are paired to the same Always reserve a channel for programming. To work on a single motor at a time, place all other motors into sleep mode. Press the "P1" button (about 6 sec) on the motor head until motor jogs x2 and beeps x2. DECLARATIONS U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CHARGING & BATTERY INDICATORS INTERNAL RECHARGEABLE BATTERY During operation, if the motor begins to beep, this is an indicator to let users know the motor power is low and needs to be charged. To charge, plug the micro-USB port on the motor into the 5V/2A charger. Blinking Red: Low battery alert Blinking Green: Charging in process Solid Green: Finished charging EXTERNAL RECHARGEABLE BATTERY PACK During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged. To charge, plug the micro-USB port on the end of the battery pack into the 5V/2A charger. Solid Red: Charging in process Solid Green: Finished charging SPECIFICATIONS Declarations AMP25B Voltage 3V (CR2450) Add A zoom in on the charging port Radio Frequency FCC Text - text 01 Transmitting Power Roller Sheer Revolve Roman shades 433.92 MHz Bi-directional 10 milliwatt Operating Temperature RF Modulation AMP25B AMP25B Lock Function 14°F to 122°F (-10°C to 50°C) , sheer shadings, roman shades, and zebra shades. P1 FSK Yes Add visual explanation of P1 - file 02 IP Rating IP20 Transmission Distance up to 200m (outdoor) Safety Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. Donotdisposeofingeneralwaste. Please recycle batteries and damage 15 CHANNEL REMOTE CONTROL PROGRAMMING AND USERS GUIDE SAFETY INSTRUCTIONS 1. Do not expose motor to humid, damp, or extreme temperature conditions. 2. Do not drill into motor. 3. Do not cut the antenna. Keep it clear from metal objects. 4. Do not allow children to play with this device. 5. If the power cable or connector is damaged, do not use 6. Ensure the power cable and antenna are clear and protected from moving parts. 7. Cable routed through walls should be properly isolated. 8. Motor should be mounted in horizontal position only. 9. Before installation, remove unnecessary cords and disable equipment not needed for powered operation. COIN BATTERY WARNING 1. Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate. 2. Even used batteries may cause severe injury or death. 3. Call a local poison control center for treatment information. 4. CR2450 is the compatible battery type. 5. The nominal battery voltage is 3.0V. 6. Non-rechargeable batteries are not to be recharged. 7. Do not force discharge, recharge, disassemble, heat above 50°C / 122°F or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns. 8. Ensure the batteries are installed correctly according to polarity (+ and -). 9. Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries. 10. Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations. 11. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children. ! WARNING · INGESTION HAZARD: This product contains a button cell or coin battery. · DEATH or serious injury can occur if ingested. · A swallowed button cell or coin cell battery can cause Internal Chemical Burns in as little as 2 hours. · KEEP new and used batteries OUT OF REACH OF CHILDREN. · Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body. · CR 2450, 3V ! 10/2024 REMOTE CONTROL OVERVIEW Please read prior to installation and use. Save these instructions for future reference. BUTTON INSTRUCTIONS Lower Channel LCD Display Up Stop P2 Down Higher Channel P2 Lock Switch P1 BUTTON LOCATION HORIZONTAL BLIND TILT MOTOR ROLLER / SHEER / DUAL / WOVEN MOTOR P1 Button LED light P1 button Lithium Battery Switch HONEYCOMB STANDARD SHADE MOTOR Power line P1 Button Signal line P1 Button REPLACING THE BATTERY a. Gently insert the included a. ejector tool into the pinhole opening and apply a small amount of pressure to the cover and slide the cover off. b. Install battery (CR2450) with positive (+) side facing up. c. Gently slide the cover back until a "click" sound is heard. b. c. Battery (CR2450) "click" ADVANCED SETTING - DISABLE LIMIT SETTING a. Remove the cover from the backside of remote, the lock switch is in the right corner. b. Move the switch to the "Lock" position to disable the following commands, remote will show "L" (lock): - Change Motor Direction - Setting the Upper and Lower Limit - Adjust Limit - Roller Mode or Sheer Mode c. Move the switch to "Unlock" position to assess all remote functions, remote will show "U" (unlock). *This advanced feature is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits. a. b. Unlock Lock Switch c. Unlock Lock Switch Switch L U CHANNEL OPTIONS SELECT A CHANNEL a. Press "<" button on the remote to select a lower channel. b. Press ">" button on the remote to select a higher channel. Action on a. Remote Control Lower Channel Remote 1 Response b. Higher Channel 15 HIDE UNUSED CHANNELS a. Press and Hold (about 3 sec) "<" and ">" buttons simultaneously until remote control displays "C" (channel). Action on a. Remote Control Remote Response b. Press "<" or ">" button to select required quantity of channel (between 1 to Action on b. Remote Control 15). Remote c. Press "Stop" button Response to confirm selection (the Action on c. example shows a 5-channel Remote selection). The LED will Control display "O" (OK) once to confirm selection. Remote Response + Lower Higher Channel Channel C or Lower Higher Channel Channel 11 Stop 5 O GETTING STARTED It is important to confirm that the motor is awake and ready to receive programming. To do this, press "P1" button on the motor less than 1 sec, to activate the motor from Sleep Mode. 1. PAIR / UNPAIR REMOTE CONTROL NOTE: Honeycomb and Horizontal Blind Motors DO NOT BEEP. a. Press "P1" button (about 2 sec) on the motor head until motor jogs x1 and beeps x1*. b. In the next 10 secs, press and hold "Stop" button on the remote control until motor jogs x2 and beeps x3*. Action on a. P1 P1 Motor Motor Response Jog x1 P1 P1 Beep x1 Action on b. Remote Control Motor Response Stop Jog x2 Beep x3 * Repeat the same procedure to unpair remote control. 2. CHANGE MOTOR DIRECTION (IF NECESSARY) This operation is only valid when no limits have been set. If the motor has the upper and lower limits set, you can only switch direction by pressing "P1" button (about 10 sec) on the motor head until motor jog x3 and beep x3. Press "Up" or "Down" button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) "Up" and "Down" buttons simultaneously until motor jogs x1 and beeps x1. Action on Remote Control Motor Response + Up Down Jog x1 Beep x1 3. SETTING THE UPPER AND LOWER LIMITS SET UPPER LIMIT a. Press "Up" button to Action on a. raise the shade, then press Remote "Stop" button when it is in Control Up the desired upper limit. Motor b. Press and hold (about Response 5 sec) "Up" and "Stop" buttons simultaneously until motor jogs x2 and beeps x3. b. Up + Stop Jog x2 Beep x3 SET LOWER LIMIT a. Press "Down" button to lower the shade, then press "Stop" button when it is in the desired lower limit. Action on Remote Control Motor Response a. Down b. + Down Stop Jog x2 Beep x3 b. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jogs x2 and beeps x3. *If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits. 4. ADJUST LIMITS ADJUST THE UPPER LIMIT Action on Remote a. Press and hold (about Control a. Up + Stop 5 sec) "Up" and "Stop" Motor Jog x1 Beep x1 buttons simultaneously Response until motor jogs x1 and beeps x1. b. Use "Up" button to raise the shade to the desired Action on Remote Control c. Up + Stop highest position, and use "Up" or "Down" button to do the final adjustment if Motor Response Jog x2 Beep x3 necessary. b. Up c. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jogs x2 and beeps x3. ADJUST THE LOWER LIMIT a. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jogs x1 and beeps x1. b. Use "Down" button to lower the shade to the desired lowest position, and use "Up" or "Down" button to do the final adjustment if necessary. Action on Remote Control Motor Response Action on Remote Control Motor Response a. + Down Stop Jog x1 Beep x1 c. + Down Stop Jog x2 Beep x3 b. Down c. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jogs x2 and beeps x3. 5. FAVORITE POSITION SET A FAVORITE POSITION a. Use "Up" or "Down" button to move the shade to desired Favorite position. Action on Remote Control a. or b. P2 Up Down b. Press and hold one "P2" button on the back of remote Motor Response or control until motor jogs x1 and beeps x1. Jog x1 Beep x1 c. Press and hold "Stop" button until motor jogs x1 and beeps x1. d. Once more, press "Stop" button until motor jogs x2 and beeps x3. Action on Remote Control Motor Response c. Stop d. Stop Jog x1 Beep x1 Jog x2 Beep x3 USING A FAVORITE POSITION Action on Remote Stop Press and hold (about 2 sec) Control "Stop" button, motor will move Shade or to Favorite position. Response REMOVE A FAVORITE POSITION a. Press one "P2" button until motor jogs and beeps x1. b. Press (about 2 sec) "Stop" button until motor jogs and beeps x1. c. Once more, press "Stop" button until motor jogs x1 and long beep x1. Action on a. Remote Control Motor Response P2 Jog x1 Beep x1 b. Stop Jog x1 Beep x1 Action on Remote Control Motor Response c. Stop Jog x1 Beep x1 6. HOW TO TOGGLE FROM ROLLER MODE / SHEER MODE ROLLER SHADE MODE - Default mode, allows for continuous raising/lowering of shade after a short press a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jogs x1. b. Press and hold (about 2 sec) "Stop" button until motor jogs x2 and beeps x3. Action on Remote Control Motor Response Action on Remote Control Motor Response a. + Up Down Jog x1 b. Stop Jog x2 Beep x3 For precise control and adjustment, use Sheer Shade Mode. SHEER SHADE MODE - Allows for slight adjustment after a short press and raising/ lowering of shade after a longer press a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. Action on Remote Control Motor Response Action on Remote Control Motor Response a. Up + Down Jog x1 b. Stop Jog x1 Beep x1 Continue on to step 7. QUICK PROGRAMMING GUIDE 1a. Attach the Wand -- Sheer Shadings, Banded & Roller Shades POWERWANDTM Honeycomb Shades | Banded Shades | Roller/Solar Shades Sheer Shadings | Natural Woven Shades 1b. Attach the Wand -- Honeycomb Shades 1 2 2 1 On Banded Shades, Roller Shades and Sheer Shadings, with the wand control buttons facing you, attach the top of the wand on the metal hook support (1) on the motor control side, then connect the cable into the motor head (2). Note: On Sheer Shadings ordered with Powerwand on the right side, the cable may be wrapped around the hook. This is normal. You may unwrap, if you desire, as this does not affect functionality. You still need to connect the cable into the motor head. On Honeycomb shades, the wand will be already connected to the shade (1). With the wand control buttons facing you, attach the top of the wand into the plastic hook support on the motor control side (2). 1c. Attach the Wand -- Natural Woven Shades 1 2 On Natural Woven Shades, with the wand control buttons facing you (1) approach the hook with the wand parallel to the headrail. (2) Gently twist the wand to attach it to the hook. Connect the cable into the motor. Important: Before starting the programing, install the shade following the installation instructions provided. Honeycomb shades are shipped with the motor in sleep mode to avoid activation during transit. For Honeycomb Shades, To wake up the motor prior to operating the shade: Press the STOP button 5 times (1) - the first 4 times press quickly and the 5th time PRESS and HOLD the stop button until the motor jog (2). 1 QUICK PROGRAMMING GUIDE 2. Operate the Wand UP STOP DOWN LED MICRO USB CHARGING PORT Front of wand PROGRAMMING BUTTON Back of wand Roller and Honeycomb Mode: · Press the DOWN or UP button to lower or raise the shade. Press the STOP to stop the shade at the desired position. Sheer Shadings and Banded Shades Mode: · Tapping the UP or DOWN button for less than 2 seconds will move the shade in short steps. · Holding the UP or DOWN button down for more than 2 seconds before releasing will operate the shade at the standard speed. · Press the STOP button to stop the shade at the desired position. 3. Set a Favorite Position 1 2 Press and 3 Release the PROG Move the button shade to the desired position 4 Press and 5 Release the PROG button IMPORTANT: Once the favorite position is set, the shade will always stop at the designed favorite position when passing by it. Click 2 x Up or Down button, the shade will go to set Top or Bottom Limit. 4. Remove a Favorite Position 1 2 3 Press and Hold the PROG button Move the shade to for 7 seconds Jog x2 the favorite position 5. Advanced Programming IMPORTANT: Damage to shade may occur when operating the motor prior to setting limits. Attention should be given. Switch between Roller and Sheer Shadings Mode 1 2 3 4 Press and Hold the STOP button for 5 seconds Press and Release the STOP button 2 QUICK PROGRAMMING GUIDE Adjust the Top and/or Bottom Limit 1 2 Press and 3 4 5 Press and 6 Release Release Move the shade to the limit that should be adjusted the PROG button Jog x1 Adjust the shade to the desired limit position the PROG button Jog x1 Factory Motor Reset 1 2 Press and Hold the STOP button for 5 seconds Jog x1 3 4 Press and Hold the PROG button for 7 seconds Jog x2 IMPORTANT: All limits will be erased. The motor direction will return to default and may need to be adjusted. Reverse UP and DOWN Commands (Only if necessary) 1 2 3 4 Press and Hold the STOP button for 5 seconds Jog x1 Press and Release the DOWN button Jog x1 Set Upper and Lower Limits ( Only after Factory Motor Reset) 1 Press and Release the PROG button 2 Jog x1 3 Press UP to set the TOP LIMIT 4 Adjust the shade to the desired top limit 8 Press and Release the PROG button 7 Adjust the shade to the desired lower limit 6 Jog x1 5 Press and Release the PROG button 9 Jog x1 10 Press and 11 Release the PROG button Jog x1 3 QUICK PROGRAMMING GUIDE 6. Charge the Battery A LED When the shade begins to operate slower than normal or only beeps when you attempt to operate, it is time to charge the battery. To Charge, connect a standard micro USB cable into the bottom of the wand (A) and into USB 5V/2A (max) power supply. A red LED on the wand indicates that the battery is charging. To fully charge the batteries, allow the batteries to charge for at least 1 hour after the LED on the wand turns green. Note: A typical charge cycle can take between 4-6 hours. Troubleshooting Issues Possible Causes Solution The shade is not responding Built in battery is depleted Wand is not fully connected to the motor The shade moves the opposite direction The motor direction is reversed on the control buttons The shade stops by itself before it reaches A favorite position was set the top or bottom limit The shade is operating on Sheer Shadings/ The shade only moves in small steps after Banded Shades mode pressing the button The shade has no limit set Recharge with compatible USB 5V/2A (max) adapter and a micro USB cable. Details under "6. Charge the Battery" Check the connection between the wand and the motor See details under "Reverse Up and Down Commands" See details under "4. Remove a Favorite Position" Switch to Roller/Honeycomb mode by following the steps under "Switch between Roller and Sheer Shadings Mode" See details under "Set Upper and Lower Limits" 4 1035121 · rev 06/24Adobe PDF Library 17.0