Instructions for integratech models including: RF RGBW Remote Controller, RF RGBW Controller, RGBW Remote Controller
RF RGBW Remote Controller. Function introduction. Important: Read All Instructions Prior to Installation. Output. RF signal. Operation Frequency. 869.5/916.5 ...
RF RGBW Remote Controller Important: Read All Instructions Prior to Installation Function introduction White channel: the 4th channel Click to turn on/off, Press and hold down to increase/decrease light intensity of the channel Indicator: indicate the state of remote control Touch color wheel, touch to select RGB colors Click to turn ON/OFF all zones Press and hold down to speed down under dynamic mode Press and hold down to save colors/ scenes; Click to recall the saved colors/ scenes Click to return to previous status R G B 123 456 Front side Press and hold down to increase light intensity of RGB channels Press and hold down to speed up under dynamic mode Press and hold down to decrease light intensity of RGB channels Play/Pause button, click to play/pause 10 built-in modes R/G/B channels, Click to turn off/on the channel, Press and hold down to increase/ decrease light intensity of R/G/B channel Zone numbers:Click to choose the zone/ zones, Press and hold down to turn on/off corresponding zone 3xAAA battery Product Data Output RF signal Operation Frequency 869.5/916.5/434MHz Power Supply 4.5V(3xAAA battery) Operating temperature 0-40°C · Control 6 zones of RF receivers separately. · RGBW color controller · High sensitive & high stable fast & precise color control. · Compatible with all universal series RF receivers · 1 receiver can be paired by max 8 different remote controls. · Waterproof grade: IP20 Relative humidity 8% to 80% Dimensions 140x48x17mm Safety & Warnings · This device contains AAA batteries that shall be stored and disposed properly. · DO NOT expose the device to moisture. Pair with RF receiver(Method 1) Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the instruction of RF receiver that you would like to pair with. Step 5:Touch the color wheel, LED lights connected with the RF receiver flicker once means the receiver is paired with zone 6 successfully. Step 2:Click ON/OFF button to activate the remote R G B 123 456 RF LED Receiver Learning Key Step 3:Click the "Learning Key" button on RF receiver or re-power on the receiver three times continuously to set it into pairing status Step 4:Choose and click a zone number(e.g. zone 6) Pair with RF receiver(Method 2) Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the instruction of RF receiver that you would like to pair with. Bottom side R G B 123 456 Step 2:Click ON/OFF button to activate the remote RF LED Receiver Learning Key Step 3:Power off and power on the receiver Step 4:Choose and click a zone number(e.g. zone 3) twice, then press and hold it continuously and quickly within 10 seconds, LED lights connected with the RF receiver flicker once means the receiver is paired with zone 3 successfully. Save color/scene/mode Step 3:Touch the color wheel or click the other buttons to select the scene you like Step 1:Click ON/OFF button to activate the remote R G B 123 456 Step 4:Press and hold down button S until the LED indicator of remote flash once Step 2:Choose and click one or multiple paired zone numbers(e.g. zone 3) Step 5:Immediately click any number of 1-6(e.g. 6)(here the numbers mean 6 scenes can be saved for the selected zone) , LED lights connected with the RF receiver flicker once means the color/scene was saved successfully. Recall the saved colors/scenes Built-in 10 color changing modes are as follows: Mode 1: Any two colors of RGB mix fade-in & fade-out Mode 2: RGB three colors mix fade-in & fade-out Mode 3: RGB three colors mix fade-out & fade-in Mode 4: RGB flash Mode 5: RGB three colors fade-in & fade-out successively Mode 6: RGB three colors fade-in successively Mode 7: RGB three colors fade-out successively Mode 8: RGB three colors jump changing successively Mode 9: R&B two colors mix fade (R in B out), then G fade-in, then R&B mix fade (R out B in), then G fade-out Mode 10: B fade-out, then G&B mix fade (G out B in), then R&G mix fade (R out G in), then R fade-in Step 1:Click ON/OFF button to activate the remote R G B 123 456 Step 3:Click button S Step 2:Choose and click one or multiple paired zone numbers(e.g. zone 3) Step 4:Click any numbers 1-6(e.g. 6)(here the numbers means the 6 scenes saved for selected zone) to recall the saved scene If you use multiple receivers, you have two choices: Option 1: have all the receivers in the same zone, like zone 1 RF LED Receiver Learning Key RF LED Receiver Learning Key Zone 1 RF remote Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4 RF LED Receiver Learning Key Zone 1 RF LED Receiver Learning Key Zone 2 RF LED Receiver Learning Key Zone 3 RF remote How to stop running mode of single color LED light caused by RGBW sender interference: 1. When pairing single color LED light to a single color remote, it might be interfered and paired by nearby RGBW senders, which might control the single color light into running mode. The running mode can not be stopped by the paired single color remote or by delete pairing. 2. Then we need this remote, and pair the remote to the receiver via above "Pair with RF receiver(Method 2)", then touch the color wheel to stop the running mode. 3. Then delete pairing and pair the receiver to the single color remote again, it can be controlled by the remote again. In conformity with the provisions of Council Directives Radio Equipment Directive 2014/53/EU Restriction of Hazardous Substances (RoHS) 2011/65/EC and Regulation (EC) No 1907/2006 of the European Parliament and of the Council (REACH)Corel PDF Engine Version 20.0.0.633 CorelDRAW 2018