User Guide for Kangtai models including: 52085 Heatsink Compound Paste, 52085, Heatsink Compound Paste, Compound Paste, Paste
Kangtai Electric Co.,ltd 137 RHT137 RHT137 137
PRODUCT STRUCTURE Remote control Socket Mode Indicator Brightness Sensor Function button Remote controller ON Timer button OFF Indicator light Light Sensitive Mode Timer button Unlock button 1 BATTERY INSTALLATION PAIRING SETTING INSTRUCTIONS Remote control operation method INSTRUCTIONS The socket function key operation method æ Press and hold the unlocking button while sliding the battery cover down ç Remove the battery cover CR 2032 è Install the battery é Press and hold the unlocking button while sliding the battery cover upward to lock the battery cover 2 1.Plug the remote control outlet into an electrical outlet. 2. Press and hold the Set button and release it when the OFF indicator starts to flash slowly. at least 55 inches (1.4 meters) 3. Press the ON button on the remote controller, the ON indicator light remains on constantly, the pairing is successful. Note: Please complete the operation within 120 seconds 3 Weatherproof WARNING:The outlet must be mounted in a vertical position with the outlet facing down and at least 55 inches (1.4 meters) above the floor. 1. Press the ON button to turn on the device. 2. Press the OFF button to turn off the device. 3. Press the remote control Sensor key to turn on the light control mode. The device is automatically turned on at night and off during the day. Note: The brightness sensor must not be blocked. There is a delay of about 20 seconds for photosensitive detection of brightness 4. Press the 2H button on the remote control outlet key to turn on the delayed off mode. 2H indicator light is on. The device is automatically turned on at night and turned off with a 2-hour delay after it is turned on. (4H=4 hours delayed shutdown, corresponding indicator light on.) (6H and 8H are the same) Note: The delay mode will only be executed once a day. 4 1. Mode switching: Short press the Set button to switch modes, the indicator corresponding to the selected mode blinks 3 times to indicate that the mode is selected, after blinking 3 times, the selected mode is activated. Note: When the light control mode and delay off mode are selected, the device is turned off, the corresponding function indicator light is on, and the OFF indicator light is also on. 2. Pairing mode: Press and hold the Set button of the remote control socket, release the OFF indicator after it starts to flash slowly and the device enters the pairing mode. 3. Clear receiver memory: Press and hold the Set button of the remote control socket (the process is about 20 seconds), the OFF indicator light changes from slow flashing to fast flashing, Release the Set button after the OFF indicator stops flashing to clear the device memory. 5 PRODUCT SPECIFICATION Model: 52085 Working voltage: 120V~ 60Hz 15A Max power rating: 1800W Operating range: Max 260 ft(outdoor open area) Frequency: 433.92MHz LED flash: Blue Working temperature: 0~35 Use scene: Indoor/Outdoor Standby power consumption:0.3W Model: 50137 Frequency: 433.92MHz Working temperature: 0~35 Operating voltage: 1x3V CR2032 Standby current:$ Transmit power: < 2dBm 6 FAULT ANALYSIS AND SOLUTION Problem Possible Cause Solution The indicator light of the transmitter does not flash The battery is not sufficient The installation of batteries is not correct Replace with a new battery Remove the battery and reinstall it again to make sure the contact is good The receiver does not work One switch button controls multiple outlets The pairing failed. The transmitter is too far from the receiver or there is a metal obstacle near the receiver's mounting location Multiple outlets are paired with the switch button Re-pair the receiver and transmitter again Reduce the distance between the remote control and the receiver or move the metal barrier between them Clear all pairs of the socket and then re-pair to the corresponding switch buttons 7 PRECAUTIONS 1. Use Information The following equipment must not be connected to the remote control plug: · Equipment exceeding the technical value of the remote control plug (-> technical data). · Equipment with motor capacitors (such as refrigerators, etc.). · Opening the device unattended can cause fire or other damage (such as irons,etc.). · Cathode-ray tube television. · In an emergency, you must have quick access to the remote control plugs so that they can be removed from the grounded contact plugs in the event of a hazard. 2. Safety Information · Do not plug multiple devices into each other. · There is no voltage when the plug is disconnected. · The remote control plug can only be connected to a properly installed grounded contact socket (120V_60Hz). · The remote control plug must not be plugged into an extension cord and must not be overloaded (maximum 1800W). · Do not open the device. Improper assembly may cause electric shock, short circuit or fire. · The range of the remote control plug is severely affected by structural conditions (such as reinforced concrete) or sources of electrical / electromagnetic interference (fluorescent lights, cordless phones or earphones, TV/monitors, cables, etc.). If necessary, remove disturbance sources or keep a proper distance. · Keep the equipment installation at a distance of more than 80CM from the ground. · Avoid extreme temperature, vibration and shock. · Clean with a soft, slightly damp cloth. Do not use detergents or solvents. Do not immerse in water. · Do not plug pins or other metal objects into power outlets. · Do not expose the battery to extreme temperatures such as direct sunlight or fire. Do not place the device on the heater. Leaking battery acid can cause damage. · Always install batteries with the correct polarity (+ and ), as shown in the battery compartment. · Notice! If the battery is incorrectly installed, there is a danger of explosion. · When replacing the battery, only use the same type of battery. · If the battery leaks, remove it from the battery compartment with a clothdispose the battery properly. If battery acid leaks, avoid contact with skin, eyes, and mucous membranes. If you come into contact with acid, immediately rinse the affected skin thoroughly with water and consult a doctor. · Store the battery in a well-ventilated and dry place. · If you do not use the device for a long time, remove the battery. · Risk of explosion! Do not use other reagents to charge or reactivate the battery, and do not disassemble, throw into fire or short-circuit the battery. · Remove the used battery from the device and dispose it immediately. 8 PRECAUTIONS For Both FCC & IC application: This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. 9 PRECAUTIONS WARNING INGESTIONHAZARD:Thisproductcontainsabut onceloroinbat ery. DEATHorseriousinjurycanoccurifingested. Aswalowedbut oncelorcoinbat erycancauseInternalChemical Burnsinaslit leas2hours. KEEPnewandusedbat eriesOUTOFREACHofCHILDREN Seekimmediatemedicalattentionifabat eryissuspectedtobe swal owedorinsertedinsideanypartofthebody. Coin-cell Battery Type: CR2032 Nominal Voltage: 3.0Vdc Product use of battery cover is a must. 10 40 WARNING: Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children, Do NOT dispose of batteries in household trash or incinerate. Even used batteries may cause severe injury or death If the coin-cell battery is swallowed or placed inside any part of the body, call a local poison control center for treatment information. The non-rechargeable battery is not to be recharged. Do not force discharge, recharge, disassemble, heatabove 60°C (140°F) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns. Ensure the batteries are installed correctly according to polarity (+ and-). Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries. Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children. Warning: contains coin battery Wireless Light Sensor Remote Control Socket with Timer User Guide Model: 52085+50137Adobe PDF library 15.00