User Manual for ROSE LIGHTING models including: L8 Forum Rose Lighting Kinetic Lifting Ball, L8 Forum, Rose Lighting Kinetic Lifting Ball, Lighting Kinetic Lifting Ball, Kinetic Lifting Ball, Lifting Ball, Ball
L8 FORUM - View topic - Rose Lighting Kenetic Lifting Ball
Lifting System Brief Manual Display and Touch Buttons Press MENU to start setting or returning to the upper option; Press UP/DOWN to browse into the menu options or to adjust the values; Press ENTER to confirm or enter a sub-option. Operation instructions MENU UP DOWN ENTER Option Addr rESt ConF Sub-option ALL FACt MOdE nSiG inFO CHnL diSP ModE V101 dMod DMSG Value 001-512 SurE Strr P234 7CH/8CH Crdt/HdLE 1rEd 2Grn 3bLU 4diM 5FSH 6tiL 7SPd 8CtL ALon/dYoF rECE Functions To set the DMX address code of the unit To reset all functions To recover the factory settings To set the unit in 7CH or 8CH mode To clear all outputs after 2 seconds (Crdt) or to hold the last DMX value before the DMX is off (HdLE). CH1 Red dimmer CH2 Green dimmer CH3 Blue dimmer CH4 Master dimmer CH5 Strobe CH6 Lifting CH7 Lifting speed, not available in 7CH mode CH8 Control. In 7CH mode, it shows as "7CtL" in CH7. Firmware version To set display always on (ALon) or auto off after 5-second idling (dYoF) To set the unit in DMX mode Note: The functions in grey are for a LED color sphere, which should be purchased separately. DMX Chart Channel CH1 CH2 CH3 CH4 CH5 CH6 CH7* CH8** Value 0 1-255 0 1-255 0 1-255 0-255 0-9 10-19 20-209 210-255 0 1-255 0-255 0 Functions Close Red dimmer Close Green dimmer Close Blue Master dimmer Disable CH1-CH4 Enable CH1-CH4 Strobe, slow fast, enable CH1-CH4 Enable CH1-CH4 When CH8=0, the cord wheel will keep locked. Lifting from top to bottom Lifting speed, fast slow (Unavailable in 7CH mode) When CH6=0, the cord wheel will keep locked. 1-239 Unlock Before operating CH6, unlock should be implemented; And, to reach the 240-245 Reset perfect effect, the unit need to reset twice: Once when power is on; Another at 246-255 Unlock CH8=(240-245). * The speed channel is unavailable in 7CH mode; ** The unlock/reset channel will be the 7th channel in 7CH mode. Note: The function channels in grey are for a LED color sphere, which should be purchased separately. IMPORTANT!!! Please DO NOT run the machine before the payload is properly applied! If the hoist is powered off in a DMX mode, you must set both CH6 and CH8 (8CH mode) or both CH6 and CH7 (7CH mode) to 0 on the connected DMX controller before turning on the power of the hoist again; After power on again, the unit needs to be reset twice: Once when power is on; another reset at CH8=(240-245) (8CH mode) or CH7=(240-245) (7CH mode). Otherwise, the hoist may run in error. Warnings: Please keep sufficient safety distance and lifting distance in installation Sufficient safety distance must be considered in installation. Basic configuration of LED color sphere with lifting system Sufficient lifting distance must be considered. Otherwise, the ball may heat the ground or it will occur unexpected touches. Hoist LED Color Sphere Optional accessories (sold separately) Clamp XLR cable for DMX Safety Rope Installation Step 1: Attach the clamp to the Step 2: Hang the hoist on the truss, fasten Step 3: Attach the LED color sphere to hoist the clamp and correctly use the safety rope the hoist Cautions: Do not run the hoist without any payload being applied. The lifting cord is inside the hoist when in package. When you take out the hoist, the LED color sphere must be hung to the hoist BEFORE you power on the hoist. Running the hoist without any payload is prohibited, because the lifting cord may be entangled inside the cordwheel and cause error. Step 1: Once the payload is applied, power on the hoist. The hoist will start resetting. Flashes with input. Lights up when power on Indicates the DMX address Step 2: Connect a DMX console to test the hoist. Push 6CH to 20 to check the DMX connection. If the sphere properly descends, that means the connection is fine and the hoist rolls well. After testing, push 6CH back to 0. The sphere should move up / down smoothly. Step 3: Connect the hoists to a DMX console and reset them again by DMX: Move 8CH to 240~245. If any of the hoists do not reset, check the DMX connections. Use 8CH to reset Reset at 240~245 Correct position after resetting Incorrect position after resetting Step 4: Move 8CH to outside 240-245; Otherwise, the unit will keep the time. Make sure that all the hoists are reset correctly and the balls the correct position. Then, you can start operate the fixtures. Please mind when programming a chase. Move 8CH to finish resetting At about 100 resetting all reposition to keep this in Tips: 1: The dimmer channels (1CH-4CH) shall be enabled by 5CH; 2: The strobe effects (5CH) will only be seen when the light is activated in the dimmer channels (1CH-4CH). 3: 6CH is for lifting up and down. Fade in and fade out (slope) is not applicable to this channel. Please take into account the lifting up/down time when programming a chase. If a new chase step is made before the lifting up/down is completed in a previous step, error may occur and/or noise may be heard. 4CH Master Dimmer 5CH Strobe 6CH Lifting. Consider time problem. Fade in/out is not applicable to this channelcairo 1.17.4 (https://cairographics.org) Mozilla Firefox