PHOENIX GOLD ZXM500.1 Series Full Class d Technology Mini Amplifiers Instructions

Instructions for PHOENIX GOLD models including: ZXM500.1, ZXM500.4, ZXM600.3, ZXM700.5, ZXM500.1 Series Full Class d Technology Mini Amplifiers, ZXM500.1 Series, Full Class d Technology Mini Amplifiers, Class d Technology Mini Amplifiers, d Technology Mini Amplifiers, Technology Mini Amplifiers, Mini Amplifiers, Amplifiers

Länk till produktdatablad »

Phoenix Gold ZXM700.5, 5-kanals Mini slutsteg

Phoenix Gold ZXM600.3. 3-kanals Mini slutsteg

Instructions

ZXM600.3 - 3 Channel Mini Amplifier

File Info : application/pdf, 16 Pages, 2.59MB

ZXMAmplifiers Manual 240524 v2

FULL CLASS-D TECHNOLOGY MINI AMPLIFIERS

Models: ZXM500.1 - ZXM500.4 - ZXM600.3 - ZXM700.5
SPECIFICATIONS
· Full Class-D technology offers efficiency & performance · Short circuit/thermal and high/low voltage protection · Excellent signal to noise ratio and FM noise rejection · Remote gain controller included (except ZXM500.4) · Built in protection LED light status indicator · Surface mount component technology · Ultra small size for easy installation · Autostart on high-level input · Full adjustable HP & LP filter
All specifications subject to change without notice.

Class: Channels: Frequency Response: Max Power Rating: RMS Power Rating (1): RMS Power Rating (2): RMS Power Rating (4):
Signal to Noise Ratio (SNR) (Full Power): Total Harmonic Distortion (THD):

ZXM500.1
Class D 1
12Hz 280Hz 1000W
1 x 500W 1 x 360W 1 x 230W
-88dB <1%

ZXM500.4
Class D 4
10Hz 30kHz
1000W N/A
4 x 125W 4 x 80W 2 x 250W Bridged
-90dB
<1%

Low Pass Filter (LPF):

40Hz 250Hz (12dB/Oct)

40Hz 400Hz (12dB/ Oct)

High Pass Filter (HPF):
Subsonic:
Bass Boost @ 45Hz: Crosstalk: Input Sensitivity: Remote: High-level Input: Auto Turn-on: Input Mode: Operating Voltage: Idle Current: Current Draw (Max): Total Efficiency (4): Power Terminal: Speaker Terminal: Dimensions (LxWxH) (Excluding Feet): Dimensions (LxWxH) (Including Feet):

Sub: 50Hz 250Hz (24dB/Oct)
Sub: 50Hz 250Hz (24dB/Oct) 0 +18dB N/A 0.34V 7.1V
Yes (Included) Yes Yes N/A
7V 16.5V 0.51A 46A 92% 10mm² 10mm²
149 x 83.1 x 34.8mm 165 x 83.1 x 34.8mm

F/R: 40Hz 400Hz (12dB/Oct)
N/A
N/A
0.34V 5.7V N/A Yes Yes
2CH / 4CH 7V 16.5V
0.72A 46A 90% 10mm² 1mm² 149 x 83.1 x 34.8mm 165 x 83.1 x 34.8mm

ZXM600.3
Class D 3
L/R: 20Hz 25kHz Sub: 10Hz 250Hz
1200W N/A
2 x 130W + 1 x 350W
2 x 75W + 1 x 230W
L/R: - 86dB Sub: -91dB
<1% L/R: 40Hz 400Hz
(12dB/Oct) Sub: 50Hz 250Hz
(24dB/Oct) 40Hz 400Hz (12dB/Oct)
N/A
Sub: 0 +18dB -48dB
0.36V 6.8V Yes (Included)
Yes Yes 2CH / 3CH 8.5V 16.8V 0.88A 56A 88% 10mm² 1mm² 149 x 83.1 x 34.8mm 165 x 83.1 x 34.8mm

ZXM700.5
Class D 5
F/R: 20Hz 25kHz Sub: 10Hz 260Hz
1400W N/A
4 x 100W + 1 x 350W
4 x 60W + 1 x 230W
F/R: -84dB Sub: -89dB
<1% F/R: 40Hz 400Hz
(12dB/Oct) Sub: 50Hz 250Hz
(24dB/Oct) 40Hz 400Hz (12dB/Oct)
N/A
Sub: 0 +18dB -50dB
0.34V 8V Yes (Included)
Yes Yes 4CH / 5CH 8.6V 16.6V 1.24A 70A 85% 10mm² 1mm² 186 x 83.1 x 37.3mm 202 x 83.1 x 37.3mm

Installation
Make sure the enclosure is firmly fixed in your vehicle. Check before drilling or cutting holes. DO NOT work near fuel tanks, fuel lines hydraulic lines or electrical wiring. Amplifiers are generally mounted in the hatch/trunk area of a car or SUV, and under or behind the seat of most trucks. Select a location that will provide adequate ventilation for the amplifier. Secure the amplifier with the screws provided. DO NOT mount the amplifier in such a way as to pinch or damage the wires.
1. Before you start, disconnect the car battery's negative cable and ensure it is isolated during the installation. 2. Run an appropriate gauge wire from the battery to the amplifier. Ensure that the wire being used is good quality as this cable will carry a very high current. 3. Find the closest clear metal area to the amp for a ground. Sand, grind or scrape all paint and undercoating from the body and screw the ground securely in place.
Test the ground with an ohm meter if desired. 4. Decide where you are ideally going to mount the amp. Once placed, run the speaker wire to the speakers. Make sure the polarity (+ and -) are correctly installed. 5. Connect the power and ground to the amplifier. 6. Connect the power wire to the battery using a fuse capable of the total current load of all amplifiers connected. Locate the fuse as close as possible to the battery. 7. Connect the remote wire from the head unit to the amplifier. 8. Connect the RCA's to the amplifier. 9. When everything is connected, power on the unit and leave the gain all the way down at first. Start with the head unit volume low and work your way up. 10. Now you can tune the amp. Take your time and make only one adjustment at a time. It may take some time to get the system fully adjusted.
During this time, the amp is drawing current from the battery. You should check the battery voltage from time to time and re-charge it if it gets low.

ZXM AMPLIFIERS - Connection Diagrams ZXM500.1 Install
© 2024 Phoenix Gold - www.phoenixgold..com

ZXM AMPLIFIERS - Connection Diagrams ZXM500.4 Install - NORMAL
© 2024 Phoenix Gold - www.phoenixgold.com

ZXM AMPLIFIERS - Connection Diagrams ZXM500.4 Install - BRIDGED
© 2024 Phoenix Gold - www.phoenixgold..com

Connection - Cable Information
Ensure the audio system is turned off before making any connections to the amplifier, speakers, or source unit. Failure to do so could result in permanent damage to the audio system. Ensure the correct gauge cable is used for all connections; consult the cable calculator diagram below for the correct gauge cable for your installation.
If aluminium wire is used, it is recommended to increase the size of the gauges to compensate. The calculation of cable gauge size considers the resistance of terminal connections.
ZXM500.1 - Line Diagram
© 2024 Phoenix Gold - www.phoenixgold.com

Disclaimer
Always ensure the enclosure is securely attached, to avoid movement. PHOENIX GOLD accepts no responsibility for damage or injury in relation to inappropriate securing of this product.
Phoenix Gold Product Warranty
LIMITED WARRANTY ON AMPLIFIERS
Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Phoenix Gold dealer. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Phoenix Gold or it's Country distributor / reseller will (at its discretion) repair or replace the defective product with new or re-manufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

REV 22/05/24

References

Adobe PDF Library 17.0 Adobe InDesign 19.4 (Macintosh)