Installation Guide for Rosewill models including: RMS-E41, RMS-E41_A, RMS-E41 Monitor Desk Mount, Monitor Desk Mount, Desk Mount
5 Insert cables into cable covers. Leave enough slack of cables at arm joints for full adjustment. Installation INSTRUCTIONS 07 2-9kgs/4.4-19.8lbs Load 15” - 27” 75x75, 100x100
Rosewill Single Monitor Mount, 15 to 32 Inch, 4.4 to 19.8lbs, Adjustable Gas Spring Monitor Arm with Cable Management, Clamp & Grommet Base - Newegg.com
4 S=5mm B 1BSSNFTTUPEPBXIPOSUJI[PFO UBM QPTJUJPO S=5mm NOTE: Turn clockwise to reduce tension for lighter monitors and counter-clockwise to increase tension for heavier monitors. Use a hex wrench to adjust the height tension of the gas spring arm, to keep different weight of monitors still at any position. 5 S=5mm S=5mm B Use a hex wrench to adjust the damp for tilting. Turn counter-clockwise to reduce damping and clockwise to increase damping. Insert cables into cable covers. Leave enough slack of cables at arm joints for full adjustment. 07 RMS-E41_A RMS-E41 Thank you for purchasing a Rosewill Monitor Desk Mount. Please read the instruction manual before use and retain for future reference. 15" - 27" Tilt +90°/-85° Load 2-9kgs/4.4-19.8lbs VESA 75x75, 100x100 Swivel 180° Rotate 360° Installation INSTRUCTIONS WARNING STATEMENTS Warning Prior to the installation of this product, the installation instruction must be read and completely understood. Failure to do so may result in personal injury, property damage or voiding of factory warranty. Do not install on a structure that is prone to vibration, movement or chance of impact. Reinforce the structure as required before installation. The desk clamp can support a maximum thickness of 10 cm. Confirm the desk edge before installation. Pay attention to the weight capacity of the mount. Exceeding the limitation can result in function unworkable or even serious personal injury and property damage. Never operate the mount if parts are missing or damaged. Contact your local service center for warranty service. PRODUCT LINE GRAPH Max.520mm/20.5" 90 360 360 25 45 85 180 OR 3 Recessed surface installation:Put spacers between headplate and monitor. Install the upper two screws and don't screw them tight. Leave some space and hang the monitor on the head plate. M4x30 12x5.8x16 A 1 2 3 Recessed surface installation:Put spacers between headplate and monitor. Install the lower two screws and fasten the upper two screws. 145-395mm/5.7-15.6" 01 06 3 M4x12 Flush surface installation: Install the upper two screws and don't screw them tight. Leave some space and hang the A monitor on the head plate. 1 2 TOOLS REQUIRED NOT INCLUDED PARTS INCLUDED 3 Flush surface installation: Install the lower two screws and fasten the upper two screws. 05 a b c d e A M4x12 (x4) M4x30 (x4) 12x5.8x16 (x4) B S=3mm (x1) S=4mm (x1) S=5mm (x1) C M6x12 (x3) 02 1 Desk Clamp installation S=4mm S=4mm B M6x12 C S=4mm S=4mm MAX:60mm OR Grommet installation NOTE:If your desk has an existing grommet hole, Please install directly. If there is no existing grommet hole,make a mark on your mounting surface,and use a drill to drill a hole (40-60mm) in the mounting surface. S=4mm S=4mm 03 MAX:60mm NOTE:Change the clamp default holes S=4mm if desktop is between 60-100 mm. B S=4mm S=4mm Adjust the desk clamp height using different hole position 2 S=3mm MAX:100mm S=3mm B Install the lower arm to the base. Insert the gas spring arm above the lower arm. 04 S=3mmAdobe PDF library 17.00