REDRAGON SNIPER PRO Wired & Wireless Gaming Mouse

Dear Customer

Thank you for choosing REDRAGON. To protect your legal rights and for better customer service, we provide repair, return, and replacement after-sales service in accordance with the 'Limited Liability for Repair, Return, and Replacement of Microcomputer Products' of the People's Republic of China. The product repair warranty explanation is as follows:

• Within the warranty period, repairs due to electrical circuit problems are included. Man-made damage (such as disassembly, strong impact, water immersion, incorrect current or voltage input) and natural disasters (such as fire, earthquake) are not covered.
• Consumable parts (such as foot stick) and spare parts replacement are not included in the warranty.
• Please fill out the warranty card. The warranty card is invalid without the stamp of the retailer. It will not be reissued if lost. Please keep it in a safe place.

System Support

Windows XP/Vista/Win7/Win8/Win10

Button Description

The REDRAGON SNIPER PRO mouse features the following buttons:

• Left button
• Right button
• Scroll wheel
• Forward button
• Backward button
• Mode switch button (located on the bottom)
• DPI+ button (default: cursor acceleration)
• DPI- button (default: cursor deceleration)

Diagram description: An illustration of the mouse from a top-down perspective, highlighting the positions of the left button, right button, scroll wheel, forward button, and backward button. A separate illustration shows the bottom of the mouse, indicating the mode switch button.

Basic Operation

How to Connect the Mouse (Wired)

1. Take out the USB to USB-C cable from the package and connect the mouse to your computer.
2. Slide the power switch on the bottom of the mouse to "Power On with LED ON" or "Power On without LED ON".
3. The computer will automatically recognize and configure the mouse.
4. The mouse is ready for use once configuration is complete. The LOGO LED and lower edge LED will illuminate if the power switch is set to "Power On with LED ON".
5. The mouse recharges regardless of the power switch position. If set to "Power ON with LED OFF", the LEDs will not light up during charging. Full charge takes approximately four hours with LED backlight off, and about two hours with LED backlight on. The scroll wheel light will flash when the battery is low.

Wireless Connection

1. Take out the USB receiver from the package and plug it into any available USB port on your computer.
2. Slide the power switch on the bottom of the mouse to "Power On with LED ON" or "Power On without LED ON".
3. The computer will automatically recognize and configure the mouse.
4. The mouse is ready for use once configuration is complete. The LOGO LED and lower edge LED will illuminate if the power switch is set to "Power On with LED ON".
5. The mouse can operate for approximately nine hours with LED backlight off, and about two hours with LED backlight on. The scroll wheel light will flash when the battery is low.

How to Select DPI

The two top buttons are set to DPI+/DPI- by default. The four red DPI indicators on the side of the mouse show the current DPI value:

• All LED OFF: 1000 DPI
• One LED ON: 2000 DPI
• Two LED ON: 4000 DPI
• Four LED ON: 16000 DPI

Diagram description: An illustration of the mouse with four small indicator lights on the side, showing different combinations of lights corresponding to DPI settings.

How to Switch the Working Mode

The mouse has two working modes. Change modes using the mode button on the bottom. When pressed, the scroll wheel flashes blue-violet four times (slowly or quickly), and the polling rate is set to 125Hz or 1000Hz respectively. DPI, backlight effects, and button functions can be independently configured via software for each mode.

How to Recharge the Battery

When the battery is low, recharge it promptly. Connect the mouse to any powered output port using the USB to USB-C cable. During charging, the scroll wheel illuminates and flashes: first red (if very low), then yellow, and finally solid green when fully charged. Simultaneously, the side edge light will illuminate and expand from back to front in red until fully charged. The battery supports over 300 recharge cycles. The mouse can be used while charging. Note: Slide the power switch on the bottom of the mouse to ON.

How to Reconnect the Mouse with the USB Receiver

The mouse may lose connection due to strong magnetic fields or violent shocks. To reconnect, unplug and replug the receiver. Slide the mouse's power switch to ON, then press and hold the left, middle, and right buttons simultaneously until the scroll wheel lights up and flashes yellow-green. The scroll wheel will flash for about twenty seconds before returning to its previous light effect. Reconnection is then complete, and the mouse can be used again.

Features

Auto Sleep and Smart Shutdown

The mouse enters sleep mode after eight minutes of inactivity, or if the computer is turned off or the USB receiver is unplugged. Wake the mouse by clicking any button (except DPI+/DPI- buttons).

Low Battery Indication

The scroll wheel light will flash yellow when the battery is low.

Backlight Effects (set via software)

• LOGO Effects: Steady ON, Respiration, Streaming, OFF.
• LED Effects: Steady ON, Respiration, Streaming, OFF.

Storage for the Nano USB Receiver

The Nano USB receiver can be conveniently stored in a dedicated slot at the bottom of the mouse.

Software Instructions

Download the software from www.redragonzone.com. After installation, you can customize various functions and settings:

• DPI value can be set from 100-16000 DPI.
• Continuous keystroke function: Set the number of clicks and delay time.
• LOGO backlight mode: ON/OFF.
• Side edge backlight mode: ON/OFF.
• 10 of the mouse buttons can be remapped to various actions.
• The polling rate can be set to 125Hz/250Hz/500Hz/1000Hz. By default, working mode 1 is 125Hz, and working mode 2 is 1000Hz.
• The percentage of battery power will be displayed in the main software interface.

Diagram description: A screenshot of the mouse's software interface, showing options for DPI settings, button assignments, polling rate, and backlight effects. A battery level indicator is also visible.

Frequently Asked Questions (FAQ)

1. If the mouse is not responding: Check if the mouse is correctly plugged into the computer's USB port, or try another USB port.
2. If the cursor is moving slowly, jumping, or with abnormal movements: Try using the mouse on a clean, flat, and non-reflective surface. Dirt, dust, or uneven surfaces can affect performance. Using a mouse pad is highly recommended.