ANKO Smart Wi-Fi Sunset Lamp

TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE, INDOOR USE ONLY.

SAFETY INFORMATION:

• Remove set from packaging before connecting to the power supply.
• Before using or re-using the set, inspect the set carefully.
• Use only with the 5V DC 1A adaptor. (Standard Phone Charger - Not included)

Note: When connecting, please ensure the arrows on the USB connector and the power port are aligned with one another.

1. Connection Preparation

It is important that your phone is connected to 2.4Ghz Wi-Fi and not the 5GHz. To verify your mobile phone is connected to a 2.4Ghz Wi-Fi network, navigate to the Settings menu and click on Wi-Fi ⚙️. In this menu, you will see all detectable networks in your area. Locate the SSID for your network, select a Wi-Fi SSID that doesn't end with 5GHz.

Check that you have a strong Wi-Fi signal (at least two bars) in the location where the smart device is installed. If you don't have at least two bars signal on your phone, then you may need to reconsider the location or getting a Wi-Fi extender to boost the Wi-Fi signal strength.

If you have a dual-band router but you don't see two Wi-Fi name SSIDs, one with 5G and one without 5G, you MUST log into the router and manually disable the 5Ghz Wi-Fi signal if you're having connection issues. Please contact your internet provider on how to disable 5Ghz Wi-Fi for your router.

2. Install the APP and Register Account

For the best experience, download the "Mirabella Genio" APP to your smartphone from the App Store or Google Play. The APP icon will be displayed after it's installed successfully.

EZ Method - When the Light is Fast Blinking

1. Connect the USB cable to a USB port or standard 5V phone charger, wait for the Sunset lamp to start blinking.
2. If it did not automatically start to blink fast when powered on, press and hold the pairing button on the Wi-Fi controller until the sunset lamp light starts to blink rapidly (one blink per second). It is ready to pair using the EZ method.
3. Open the Mirabella Genio APP, tap the '+' icon, select 'Add Manually', then choose 'Sunset Lamp' from the list of devices.
4. Enter your 2.4Ghz Wi-Fi name and password (make sure Wi-Fi name doesn't end with -5G). Follow the APP instructions carefully to complete the network pairing process.

AP Method - When the Light is Slow Blinking

If the fast-blinking method (EZ method) doesn't work, please try the slow blinking (AP method) below.

While the sunset lamp light is rapidly blinking, press and hold the pairing button on the Wi-Fi controller again and then wait for the light to start blinking slowly (1 blink per every 2 seconds).

1. Open the Mirabella Genio APP, tap the '+' icon, select 'Add Manually', then choose 'Sunset Lamp' from the list.
2. Enter your 2.4Ghz Wi-Fi name and password (make sure the Wi-Fi name doesn't end with -5G). On the 'Choose the pairing mode EZ or AP mode' screen, tap 'EZ Mode' (located in the top right corner). Then select 'AP Mode'. Confirm the indicator is slowly blinking. Hit 'Next', then 'Go to Connect', and connect to the Wi-Fi network named 'SmartLife_XXXX'.

Note: If you fail to see a Wi-Fi name beginning with the word 'SmartLife_XXXX', it means the device was not slowly blinking. Please reset and make it slowly blinking by holding the pairing button.

After Connecting

After connecting to 'SmartLife_XXXX', return to the Mirabella Genio APP. The App will commence the 0-100% countdown and connection process.

Troubleshooting Timeout Errors:

To determine the cause of a timeout error, please check our online FAQ page and ensure:

• You entered the correct 2.4Ghz Wi-Fi name and password.
• The Wi-Fi controller is in a location with good Wi-Fi coverage; try moving it closer to the router.
• 5Ghz Wi-Fi signal is turned off on the router (it can be turned on after the device is connected).

If the light never stops blinking, there might be an issue with the Wi-Fi controller. Check the online FAQ page before returning it.

If the light stopped blinking but cannot progress to "register on cloud", it indicates a communication error with your router to our cloud service.

Bluetooth Pairing Assistant Function

The Genio smart Wi-Fi range includes a Bluetooth pairing assistant function for easier pairing. To use this function: Turn on your phone's Bluetooth. Switch on the wall power point, wait for the light to start blinking rapidly (2 blinks per second).

1. If it doesn't blink rapidly when powered on, press and hold the pairing button on the Wi-Fi Controller.
2. Open the Mirabella Genio APP, tap the '+' icon, and follow the steps to pair the sunset lamp light. Ensure you use the 2.4Ghz Wi-Fi name and password, not one ending in -5Ghz.

If this method doesn't work, turn OFF your Bluetooth on your phone and try the AP method.

FAQ

Q. My device went offline after an internet/power outage and won't reconnect by itself?

A. Go to the device's settings page (tap the pencil icon ✎), look for "remove device". Remove it, reset the device, and pair it again through the app.

Trademarks and Manufacturer Information

[CE logo] [FC logo] [RoHS logo] compliant. Made in China.

ANKO, HOME&CO AND AUDIOSONIC® ARE TRADEMARKS OF KMART AUSTRALIA LIMITED.

Manufacturer: MIRABELLA INTERNATIONAL PTY LTD

1 MIRABELLA DRIVE, TULLMARINE, VIC, AUSTRALIA 3043

TOLL FREE: 1800 636 528, www.mirabellagenio.com.au