SereneLife SLBKRS3 Home Mechanic Bicycle Repair Stand

What's in the Box:

• Repair Stand Base Assembly
• Top Tube Assembly
• Clamping Assembly
• Hand Knob
• Flange Lock Nut M6
• Hard Stop
• Coped Washer
• Leg Washer M6
• Button Head Cap Screw (M5x12mm and M6x60mm)
• Hex Tool (3mm and 4mm) ?
• 10mm Flat Wrench Tool ?

Assembly Instructions

Step 1: Attach Hard Stop

Line the Hard Stop (#F) up with the two holes in the Large Vertical Upright (#A) such that the arrow on the Hard Stop (#F) is pointing upward. Using a 3mm hex wrench ?, insert the M5 x 12mm Screws (#K.a) into the holes in the Hard Stop (#F) and screw them into the Large Vertical Upright (#A). Tighten to 3.5Nm max (Do Not Overtighten).

Diagram shows the Hard Stop (#F) aligning with holes on the Vertical Upright (#A), with screws (#K.a) being inserted using a hex wrench.

Step 2: Secure the Yoke

Slide the Yoke down the Large Vertical Upright (#A) until it bottoms out on the Hard Stop (#F). Insert the M6 Flange Nut (#E) into the hex pocket in the Yoke. From the other side of the Yoke, insert the Knob (#D) into the hole in the Yoke. Screw in the Knob (#D) until it is fully tightened. Fully tightened is when both flanges on the Yoke come into contact with each other.

Diagram illustrates the base assembly with the Yoke sliding down the Vertical Upright, secured by the Hard Stop. The Knob (#D) and Flange Nut (#E) are shown.

Step 3: Assemble Legs

Assemble and install the hardware and mating pieces in the order shown through each leg. Using a 4mm hex wrench ? and a 10mm flat wrench ?, tighten the M6x60mm screw (#K.b) to 5Nm.

Diagram shows the leg assembly with hardware (washers G, H, lock nuts I) and screws (#K.b) being attached.

Step 4: Install Clamp Assembly

Disassemble the clamp assembly and install it into the top tube assembly as shown in the image.

Diagram depicts the clamp assembly components being attached to the top tube.

Step 5: Mount Top Tube

Slide the top tube assembly into the repair stand base assembly. Push the collar down until it stops. Using a 3mm hex wrench ?, tighten the bottom screw on the collar. Set the top tube assembly at the desired height and fully tighten the hand knob on the collar.

Note: Do not set height beyond the "max" line on the top tube assembly.

Product Overview

The SereneLife SLBKRS3 is a blue, sturdy bicycle repair stand. It features a stable base with three legs, a central vertical support pole, and an adjustable clamp at the top designed to hold a bicycle frame or seatpost. The stand is designed for home mechanics and portable use.

Features:

• Micro-Adjustable Clamp, 360 Degrees of Clamp Rotation
• Narrow Jaws to Fit into Tight Areas
• Upgraded Collar and Leg Supports
• Portable and perfect for the Mobile Mechanic or Garage
• All Steel Construction
• Durable Textured Powder Coat Finish
• Teardrop-shaped Tubing adds Strength and Rigidity
• Compatible only with Two-wheeled Pedal-driven Bicycles

Technical Specs:

• Construction Material: Steel
• Load Capacity: 66.7 lbs.
• Adjustable Clamp: 1" to 2.75" Diameter Tubes
• Folded Dimensions (L x W x H): 45.3" x 13.8" x 9.4"
• Unfolded Dimensions (L x W x H): 27.6" x 52.4" x 39.3" - 61.0"