Select a Region | Rockwell Automation
User Guide for WEINTEK models including: PLC-5-10, PLC-5-15, PLC-5-25, PLC-5-11, PLC-5-20, PLC-5-30, PLC-5-40, PLC5 Ethernet Compatible, PLC5, Ethernet Compatible, Compatible
Weintek, драйверы контроллеров ПЛК PLC совместимых с Weintek
File Info : application/pdf, 3 Pages, 235.28KB
DocumentDocumentRockwell PLC5 Website: https://www.rockwellautomation.com/ Note: Rockwell PLC5 driver uses CRC checksum. PLC Connection Guide HMI Setting: Parameters PLC type PLC I/F Baud rate Data bits Parity Stop bits HMI sta. no. PLC sta. no. Recommended Rockwell PLC5 RS232 19200 8 Even 1 0 1 Options Notes 9600, 19200 8 Even, Odd, None 1 1-31 PLC Setting: Communication mode DF1 Full Duplex protocol 19200, None, 8, 1 (default) Allen-Bradley PLC-5 Family PLCs use DF1 Full Duplex protocol. For PLC-5/10, PLC-5/15 and PLC-5/25, MT8000 should be connected to the DF1 port on the 1785-KE module. For PLC-5/11, PLC-5/20, PLC-5/30 and PLC-5/40, MT8000 should be connected to the Channel 0 Port on the PLC. Device Address: Bit/Word Device B I1 B O0 B B3 B B10 ~ 13 B S_Bit B Bfn B NfnBit W T4SV W T4PV Format Range DDDdd 0 ~ 25515 DDDdd 0 ~ 25515 DDDdd 0 ~ 99915 DDDdd 0 ~ 99915 DDDDDDdd 0 ~ 25599915 FFFDDDdd 0 ~ 25599915 FFFDDDdd 0 ~ 25599915 DDD 0 ~ 999 DDD 0 ~ 999 Memo Input (I) Output (O) Bit data file (B3) Bit data file (B10 ~ 13) Timer Preset Value (T4) Timer Accumulator Value (T4) Bit/Word Device W C5SV W C5PV W TfnSV W TfnPV W CfnSV W CfnPV W N7 W N10 ~ 15 W Nfn W S W F8 W Ffn Format DDD DDD FFFDDD FFFDDD FFFDDD FFFDDD DDD DDD FFFDDD DDD DDD FFFDDD Range 0 ~ 999 0 ~ 999 0 ~ 255999 0 ~ 255999 0 ~ 255999 0 ~ 255999 0 ~ 999 0 ~ 999 0 ~ 255999 0 ~ 255 0 ~ 999 0 ~ 255999 Memo PLC Connection Guide Counter Preset Value (C5) Counter Accumulator Value (C5) Integer data file (N7) Integer data file (N10 ~ 15) Integer data file (V2.5.0 or newer) Floating point data file (F8) Floating point data file (V2.5.0 or newer) Wiring Diagram: Diagram 1 RS-232 (9P D-Sub to 25P D-Sub: PLC5 CPU CH0) The serial port pin assignments may vary between HMI models, please click the following link for more information. HMI PLC Link AB CPU CH0 RS232 25P D-Sub Male Rx 2 Tx 3 GND 7 Note: PLC Connection Guide The default error checking of Rockwell PLC5 is BCC, whereas our driver is CRC. Access [Channel Configuration] from RSLogix5, under Channel 0 tab, please select "CRC" for [Error Detect].