User Guide for KRAMER models including: VSM-4x4X Matrix Switcher, VSM-4x4X, Matrix Switcher, Switcher
Application Diagrams - Kramer Electronics
16 giu 2022 — In the MATRIX mode: select the output to which the input is switched (A, B, C or D). In the VIDEO WALL mode: not used. In the MULTI-VIEW mode: select the ...
File Info : application/pdf, 4 Pages, 902.53KB
DocumentDocumentVSM-4x4X Quick Start Guide Scan for full manual This guide helps you install and use your VSM-4x4X for the first time. Go to www.kramerav.com/downloads/VSM-4x4X to download the latest user manual and check if firmware upgrades are available. Step 1: Check what's in the box VSM-4x4X 4K 4x4 Seamless Matrix Switcher/Multi-Scaler 1 Set of rack ears 1 Power cord 4 Rubber feet 1 Quick start guide Step 2: Get to know your VSM-4x4X # Feature Function 1 IN SELECTOR Buttons Press to select an HDMI input (from 1 to 4) to switch to an output or a window. OUT SELECTOR 2 Buttons In the MATRIX mode: select the output to which the input is switched (A, B, C or D). In the VIDEO WALL mode: not used. In the MULTI-VIEW mode: select the input for each window on the display. 3 ALL Button Press ALL followed by an INPUT button to connect that input to all the outputs (not available for the video wall mode). 4 OFF Button Press after pressing an output button to disconnect the selected output from the inputs. To disconnect all the outputs, press ALL followed by OFF. 5 MATRIX Mode Press to operate the system as a matrix switcher. 6 VIDEO-WALL Mode Press to operate as a video wall. 2x2 Configure a 2x2 video wall. 1x4 Configure a 1x4 video wall. 7 MULTI-VIEW Mode Press to operate in multi-view configurations: Quad 4 windows filling the display. PiP 1 window over a background image. 2 windows over a background image. 3 windows over a background image. Stacked 4 images, overlapping (maintaining aspect ratio). PoP 2 images, side-by-side (maintaining aspect ratio). 2 images, displayed as a split-screen (elongated images). 1 large window and 3 smaller images on the side (maintaining aspect ratio). 8 RCL Button Press to recall a configuration. 9 STO Button Press to store a configuration. 10 IDENTIFY Button Press to indicate which input is displayed on each output or window. The display time is set via the OSD menu. 11 RESET TO XGA/1080p Press and hold for about 5 seconds to toggle resetting the video resolution to XGA or 1080p. Button 12 PANEL LOCK Button Press and hold for about 5 seconds to toggle locking the front panel buttons. VSM-4x4X Quick Start P/N: 2 9 0 0 - 3 0 1 5 1 2 QS Rev: 2 # Feature Function 13 HDMI INPUT Connectors 14 HDMI OUTPUT Connectors 15 AUDIO OUT 5-pin Terminal Block Connector 16 RESET Recessed button Connect to the HDMI sources (from 1 to 4). Connect to HDMI acceptors (from A to D). Connect to a balanced audio source (from 1 to 4). For device restoring (for example, inactive device or failed boot-up): Before powering up the device, press the button and hold it down. Turn the unit on and release the button only after the device has completed its bootup process.). After booting-up, firmware uploading may be implemented. 17 ETHERNET Connector Connect to the PC or other Serial Controller through computer networking. 18 RS-232 3-pin Terminal Block Connector Connect to the PC or a remote controller. 19 Mains Power Connector, Fuse and Switch Connect to the mains supply and use the switch to turn the unit on or off. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. Step 3: Mount VSM-4x4X To rack mount the machine, attach both rack ears (by removing the screws from each side of the machine and replacing those screws through the rack ears) or place the machine on a table. · Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device. · Avoid uneven mechanical loading. · Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits. · Reliable earthing of rack-mounted equipment should be maintained. Step 4: Connect inputs and outputs Always switch OFF the power on each device before connecting it to your VSM-4x4X. Connecting the audio output To a balanced stereo audio acceptor: To an unbalanced stereo audio acceptor: The following are connection examples for different layout configurations, as defined by the front panel buttons and the embedded web pages. Multi-View Mode Split Screen Multi-View Mode Side by Side Multi-View Mode PiP 2 Multi-View Mode Stacked Multi-View Mode POP3 (Side) Multi-View Mode POP3 (Bottom) Step 5: Connect power Connect the power cord to VSM-4x4X and plug it into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information) Caution: · For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual. · There are no operator serviceable parts inside the unit. Warning: · Use only the power cord that is supplied with the unit. · Disconnect the power and unplug the unit from the wall before installing. · Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only. · To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit. Step 6: Operate VSM-4x4X Operate Product via: · Front panel buttons · Remotely, by RS-232 serial commands transmitted by a touch screen system, PC, or other serial controller · Embedded web pages via the Ethernet RS-232 Control / Protocol 3000 Baud Rate: 115,200 Parity: Data Bits: 8 Command Format: Stop Bits: 1 Example: (Set view mode to POP3 (Side)): #VIEW-MOD 5 Default Ethernet Parameters IP Address: 192.168.1.39 UDP Port #: Subnet mask: 255.255.0.0 TCP Port #: Gateway: 192.168.0.1 None ASCII 50000 5000