Autel MaxiIM IM608 Pro II Quick Reference Guide

This guide provides essential information for the Autel MaxiIM IM608 Pro II diagnostic tool, including component identification, safety guidelines, and operational procedures.

Device Components

MaxiIM IM608 Pro II Tablet

The MaxiIM IM608 Pro II is a sophisticated automotive diagnostic tool. Key components include:

1. 10.1-inch LCD Capacitive Touchscreen: The primary interface for interaction.
2. Ambient Light Sensor: Detects ambient brightness to adjust screen visibility.
3. Power LED: Indicates battery level, charging status, or system status.
4. Microphone: For audio input.
5. Collapsible Stand: Extends from the back to allow hands-free viewing of the tablet.
6. Built-in Battery: Provides portable power.
7. Loudspeaker: For audio output.
8. Camera Lens: For capturing images or scanning.
9. Camera Flash: Provides illumination for the camera.
10. DC Power Supply Input Port: For connecting external power.
11. Headphone Jack: For audio output.
12. USB Port: For connecting accessories or data transfer.
13. HDMI Port: For high-definition multimedia interface output.
14. USB Port: An additional USB port.
15. Mini USB Port: For specific connections or charging.
16. Lock/Power Button: Turns the device on/off with a long press, or locks the screen with a short press.

MaxiFlash JVCI

The MaxiFlash JVCI is a Vehicle Communication Interface (VCI) used for connecting the diagnostic tool to the vehicle.

1. Power Port: Connects the device and the power source with the adapter.
2. Vehicle Connector: Connects the device to the vehicle's Data Link Connector (DLC) via a standard high-density DB-26 MVCI - OBDII cable.
3. USB Port: For data communication or updates.
4. Vehicle LED: Indicates connection status with the vehicle.
5. Connection LED: Indicates the status of the communication link.
6. Power LED: Indicates the power status of the VCI.

XP400 Pro Programmer

The XP400 Pro is an advanced key and immobilizer programmer.

1. DC Port: Provides 12V DC power supply.
2. USB Port: Provides data communication and 5V DC power supply.
3. DB 26-Pin Port: Connects with the Mercedes Benz infrared collector, ECU cable, MCU cable, and MC9S12 cable.
4. Cross Signal Pins: Hold the MCU spare cable or DIY signal interface.
5. Vehicle Key Slot: Holds the vehicle key.
6. Transponder Slot: Holds the transponder.
7. Mercedes Infrared Key Slot: Holds the Mercedes infrared key.
8. Status LED: Indicates the current operating status.
9. EEPROM Component Transponder Slot: Holds the EEPROM plug-in transponder or EEPROM socket.

Safety Information and Instructions

For your safety and the safety of others, it is crucial to read and understand all safety instructions before operating the device. Autel provides safety messages to help prevent personal injury and equipment damage.

Hazard Levels:

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

General Safety Instructions:

Autel is aware of many potential hazards, but cannot advise on all possible situations. Technicians must ensure their own safety and that of others.

Always perform automotive testing in a safe environment.
Wear safety eye protection that meets ANSI standards.
Keep clothing, hair, hands, tools, and equipment away from moving or hot engine parts.
Operate the vehicle in a well-ventilated work area; exhaust gases are poisonous.
Put the transmission in PARK (automatic) or NEUTRAL (manual) and engage the parking brake.
Block the drive wheels and never leave the vehicle unattended while testing.
Exercise caution around ignition coils, distributor caps, ignition wires, and spark plugs, as these create hazardous voltages.
Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
Do not connect or disconnect test equipment while the ignition is on or the engine is running.
Keep test equipment dry, clean, and free from oil, water, or grease. Clean with mild detergent and a clean cloth.
Do not drive the vehicle and operate the test equipment simultaneously; distractions can cause accidents.
Refer to the vehicle's service manual for specific procedures and precautions.
Ensure the vehicle battery is fully charged and connections are clean and secure to avoid damaging the equipment or generating false data.
Avoid placing the test equipment on the vehicle's distributor due to potential electromagnetic interference.

Getting Started and Compliance

This device complies with FCC Part 15 and Industry Canada license-exempt RSSs. Operation is subject to conditions preventing harmful interference.

RF Warning Statement: The device meets general RF exposure requirements and can be used in portable exposure conditions without restriction.

RoHS Compliance: Complies with European RoHS Directive 2011/65/EU.

CE Compliance: Conforms to essential requirements of EMC Directive 2014/30/EU, R&TTE Directive 1999/5/EC, and Low Voltage Directive 2014/35/EU.

Initial Setup:

IMPORTANT: Read the quick guide and user manual carefully, paying attention to safety warnings. Use the unit correctly to avoid damage or voiding the warranty.
Scan the QR code (represented by a graphic) to visit the Autel website at pro.autel.com.
Create an Autel ID and register the product using the device's Serial Number (SN) and password.

VCI Connection:

Connect the VCI with the vehicle's DLC, which is typically located under the vehicle dash.

SAR Information:

The radiated output power is below FCC radio frequency exposure limits. The device should be used to minimize human contact potential during normal operation. The Specific Absorption Rate (SAR) limit is 1.6 W/Kg. Actual SAR levels may be lower than the maximum certified level.

Key Functions

Programming Function

This function requires connection between the MaxiIM IM608 Pro II tablet and the XP400 Pro.

Connect the tablet and the XP400 Pro using the included APC001 USB cable.
Software Update: Connect the key programming tool to the Internet and tap 'Update' in the MaxiIM Job Menu to view and install available updates.

Immobilizer Function

This function requires connection between the vehicle, the MaxiIM IM608 Pro II tablet, and the XP400 Pro.

Pair up the MaxiIM IM608 Pro II tablet with the VCI device via Bluetooth to establish a communication link with the vehicle.

Wireless Data Printing

To print wirelessly, a PC is required.

Download and install the Maxi PC Suite from www.autel.com > Support > Downloads > Autel Update Tools onto a Windows-based PC.
IMPORTANT: Ensure the tool and PC are on the same network (Wi-Fi or wired) as the printer.
Launch the PC Link application on the PC and navigate to the 'MaxiSys Printer' tab.
Click 'Test Print' to verify printer functionality.
On the tool, tap 'Print' on the toolbar. A temporary document is created and sent to the PC.
If 'Auto Print' is selected in MaxiSys Printer, the document prints automatically.
If 'Auto Print' is not selected, click 'Open PDF File' to view temporary files, select desired files, and click 'Print'.

	Autel MaxiIM IM508 User Manual Comprehensive user manual for the Autel MaxiIM IM508 diagnostic and key programming tool, detailing its features, operations, and safety guidelines for automotive professionals.
	Autel MaxiCOM Ultra Lite User Manual - Advanced Automotive Diagnostics Comprehensive user manual for the Autel MaxiCOM Ultra Lite diagnostic tablet, covering setup, diagnostics, service functions, maintenance, and support. Learn to use Autel's advanced automotive diagnostic tools.
	Autel MaxiSys Ultra S2 Quick Reference Guide Explore the Autel MaxiSys Ultra S2 automotive diagnostic system with this quick reference guide. Learn about its components, features, and setup for efficient vehicle diagnostics.
	MaxiAP AP200 User Manual: Comprehensive Guide to Autel's Wireless Diagnostic Tool Explore the MaxiAP AP200 User Manual for detailed instructions on using Autel's wireless diagnostic interface. Learn about its features, setup, service functions, troubleshooting, and warranty information.
	Autel MaxiSys MS909S2 User Manual: Advanced Automotive Diagnostics Discover the Autel MaxiSys MS909S2 User Manual for comprehensive automotive diagnostics. This guide covers the MaxiSys Tablet and MaxiFlash VCI2, detailing setup, safety, diagnostic procedures, service functions, and data management for professional technicians.
	AutoLink AL519 User Manual: Comprehensive Guide to OBD-II Diagnostics Explore the AutoLink AL519 user manual for detailed instructions on performing OBD-II diagnostics, reading trouble codes, accessing live data, and understanding vehicle emissions readiness. Essential for automotive technicians and car enthusiasts.
	Autel MaxiSys MS906 MAX Quick Reference Guide \| Professional Diagnostic Tool Get started quickly with the Autel MaxiSys MS906 MAX professional diagnostic tablet and MaxiVCI V200. This guide covers product features, component identification, and initial setup for vehicle diagnostics.
	Autel IM608/IM508 Key Programming Guides: Comprehensive Car Model List A detailed guide listing car models and specific key programming procedures using Autel MaxiIM IM608 and IM508 devices, including direct links to instructional YouTube videos for each procedure.