Argo NIVEO SMART

General Safety Information

• Use this fan heater only as described in this manual. Any other use not recommended by the manufacturer may cause fires, electric shock, or accidents to people.
• Ensure the power supply type complies with the electrical requirements of the fan heater (230V~50-60 Hertz).
• This fan heater is designed for wall mounting, at a minimum distance of 1.8 m from the floor and 30 cm from both sides of the wall. Do not use it on the floor.
• This appliance can be used by children aged 8 years and above, and by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, provided they are supervised or have received instructions on the safe use of the appliance and understand the inherent dangers.
• Children must not play with appliances.
• Cleaning and user maintenance must not be carried out by children without supervision.
• This product is not a toy.
• Children under 3 years of age must be kept away if not continuously supervised.
• Children aged between 3 and 8 years should only switch on/off the appliance provided it has been placed or installed in its normal operating position and they are supervised or instructed on how to use the appliance safely and understand the dangers.
• Children aged between 3 and 8 years must not switch on, adjust, or clean the appliance nor perform user maintenance.
• ATTENTION: Some parts of this product can become very hot and cause burns. Special attention must be given to children and vulnerable persons.
• To avoid the risk of unintentional resetting of the thermal protection, this appliance must not be powered by an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
• WARNING: Do not use the fan heater with a timer or any other external device that switches the fan heater on automatically, as there is a risk of fire if the fan heater is covered or positioned incorrectly.
• The appliance is equipped with an IP22 protection rating and can also be used in the bathroom, in zone 2.
• Do not use the appliance near bathtubs, showers, washbasins, or swimming pools.
• Do not obstruct the air inlet and outlet grilles.
• The heater gets very hot during use, posing a burn risk. Avoid contact of unprotected skin with the hot surface.
• Keep flammable materials, such as furniture, pillows, blankets, cardboard, clothing, curtains, and more, at a distance of 1 m from the front, sides, and back.
• Disconnect from the mains if not in use or for cleaning.
• Do not use the fan heater in dusty environments or in the presence of flammable vapors (e.g., in a workshop or garage).
• Do not place anything on the product; do not hang wet clothes on the heater.
• Use the heater in a well-ventilated environment.
• Do not allow fingers or foreign objects to enter the air inlet or outlet grilles, as this may cause electric shock, fire, or damage to the fan heater.
• To prevent fires, do not block or tamper with the grilles in any way while the heater is in operation.
• Do not use the appliance with damaged wires or plugs. If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid any risk.
• Do not use the fan heater if it has been dropped from a certain height or damaged in any way. Contact a service center for your fan heater to be checked or for electrical or mechanical repairs.
• The most common cause of overheating is dust accumulation in the appliance. Remove dust accumulations by unplugging the unit and cleaning the grilles with a vacuum cleaner.
• Do not use abrasive products to clean the appliance. Clean it with a damp (not wet) cloth rinsed with water and soap. Remove the plug from the socket before maintenance.
• To turn off the fan heater, set the switch to the OFF position and remove the plug from the socket. Simply pull the plug.
• Do not pull the cord when unplugging the heater.
• Do not place anything on the cord and do not bend the cord.
• It is not recommended to use extension cords, as the extension cord may overheat and cause a fire risk. Never use a single extension cord to operate more than one appliance.
• Do not immerse the cord, plug, or any other element of the appliance in water or other liquids.
• Do not touch the appliance with wet hands.
• Do not place the heater above or near another heat source.
• ATTENTION: DO NOT COVER THE FAN TO AVOID OVERHEATING.
• Fire hazard if, during operation, the fan heater is covered by or in contact with flammable material, including curtains, blankets, etc. KEEP THE FAN HEATER AWAY FROM SUCH MATERIALS.
• Do not connect the fan heater to the power supply until it has been properly mounted or positioned.
• Do not run the cord under carpets. Do not cover the cord with blankets, rugs, or similar. Place the cord away from occupied areas or where it cannot be accidentally tripped over.
• Do not use the fan heater near bathtubs, showers, sinks, or swimming pools.
• The heater must not be placed immediately below a socket.
• Do not use outdoors.
• On first use, the fan heater may emit a slight, harmless odor. This smell is a normal consequence of the initial heating of the internal heating elements and should not reappear later.
• ATTENTION: THE ON/OFF SWITCH IS NOT THE ONLY MEANS TO DISCONNECT POWER. If the appliance is not used, moved, or maintained, always remove the plug from the socket.
• A fan heater has parts inside that generate arcs or sparks. It must not be used in areas that may be hazardous, such as areas at risk of fire, explosion, chemical loads, or humid atmospheres.
• Always unplug the appliance when it is not in use.
• To prevent accidents, unplug the unit if it is unattended.
• In case of a fault (abnormal noise or strange smell), unplug the appliance immediately, do not attempt to repair it, and take it to the local service center.

Parts Description

Diagram showing the heater with numbered parts: 1) Front panel, 2) LED display, 3) On/off switch, 4) Air outlet, 5) Air distribution fins, 6) Remote control.

How to Install the Heater

The heater must be wall-mounted before use. Do not attempt to use it without installation. The installation sequence is as follows:

1. Prepare a space for installing the appliance.
2. Drill holes in the wall according to the instructions inside the box. Warning: Ensure you maintain the safety distances as shown in the drawing below.
3. Insert the fixing tube into the hole and place the screws into the fixing tube.
4. Carefully hang the unit on the screws. Warning: Before using the fan heater, ensure it is securely fixed to the wall.

Diagrams illustrating wall mounting: showing hole drilling points with dimensions (e.g., Ø 8mm holes, 428mm spacing, 5-7mm screw depth, 1910mm height indication).

Control Panel

Soft Touch Buttons

• Standby: [power] ON/OFF
• Mode selection/[Wi-Fi]
• [plus]
• [minus]
• [timer]

Icons on the Panel

1. Standby; ON/OFF
2. Heating mode active - low/high power
3. COMFORT Mode (5-35°C)
4. ECO Mode (1-31°C)
5. [Wi-Fi]

ON/OFF Button

Connect the power cord to a suitable electrical socket (230V~50-60 Hz), as indicated on the data plate. The fan heater will emit a beep and the LED will light up on the control panel. To turn off the fan heater, touch the [power] icon.

Heating Mode / [Wi-Fi] Button

Touch the [mode] button to select the desired heating mode in the following circular sequence:

• COMFORT Mode: Touch the [plus] and [minus] keys to set the temperature from 5°C to 35°C.
• ECO Mode: Touch the [plus] and [minus] keys to set the temperature from 1°C to 31°C.
• Anti-Frost Mode: The display shows [frost] and the reference temperature is 7°C. The temperature cannot be adjusted.
• Pre-set heating programs P1/P2/P3

OBS: If the time and date setting has not been completed, to configure programs P1/P2/P3 for the first time, you will need to select the time and day first.

Program Details

Program P1 (Monday to Sunday) – Predefined program that cannot be altered.

Program P2 (Monday to Friday) – Predefined program that cannot be altered.

Program P2 (Saturday to Friday) – Standard program that cannot be altered.

Schedule P3 (Monday to Friday) – Schedule that can be altered.

Program P3 (Saturday and Sunday) – Program that can be modified.

Configuring the Editable P3 Program:

1. When program P3 is selected, touch the [mode] button for about 3 seconds to set the day selection.
2. The display will show [day]. Touch the [plus] and [minus] keys to select the day of the week (Monday to Sunday).
3. Touch the [mode] key to confirm the selected day and set the desired time.
4. The display will show the time. Press the [plus] and [minus] keys to set the hour (00-23). Then, press the [mode] button to select the heating mode for each operating hour (icons will appear on the display corresponding to the set mode: COMFORT Mode [comfort], ECO Mode [eco]).
5. Repeat the operation until programming for each hour and each operating day is complete.

NB: After selecting the heating mode at 23:00, touch the [plus] key to restore the daily programming. When [timer] appears on the display, touch the [mode] button to complete the selections and the display will show [timer set].

TIMER AND WEEKLY PROGRAMMING BUTTON

Press and hold this button on the control panel for 3 seconds to select the timer and weekly programming.

“d” appears on the display, then touch the [plus] and [minus] keys to choose the days of the week in the following sequence (see the table with the days of the week):

• 1 Monday
• 2 Tuesday
• 3 Wednesday
• 4 Thursday
• 5 Friday
• 6 Saturday
• 7 Sunday

Touch the [mode] key to confirm the desired day and set the hour; “h” appears on the display.

Then press the [plus] and [minus] keys to select the time and press the [mode] button to confirm.

OBS: If the power is turned off, the weekly programming and the timer will be reset to factory settings.

“OPEN WINDOW” SENSOR FUNCTION

To activate the open window function, touch the [open window] and [plus] keys together; F will appear on the display. After 3 seconds, the set temperature will appear on the display.

To deactivate the open window function, touch the [open window] and [minus] keys together; FF will appear on the display. After 3 seconds, the set temperature will appear on the display.

SLEEP TIMER FUNCTION

Touch the [timer] button once; the corresponding LED on the control panel lights up and the display shows “0 H”; hold the button or the display will show the shutdown interval: 2H – 4H – 8H.

Touch the [plus] and [minus] keys to set the sleep timer from 0 to 9 hours.

HEATING POWER LEVEL ADJUSTMENT

To activate the function, press this button on the remote control to set the desired heating power level: minimum power (1000 W) or maximum power (2000 W).

AUTOMATIC OSCILLATION FUNCTION

Press this button on the remote control to activate or deactivate the automatic oscillation function of the flaps.

CHILD LOCK FUNCTION

Press the [child lock] and [power] buttons on the remote control simultaneously to activate or deactivate all buttons on the control panel, except standby; they are locked.

Wi-Fi Guide

About the Tuya Smart App

This device is equipped with Wi-Fi, which also allows you to control the device remotely via your home Wi-Fi network. The prerequisites are: a permanent Wi-Fi connection to the router and the free "Tuya Smart" app, available for Android and iOS. Scan the corresponding QR code to access the download directly.

QR code for Android download.

QR code for iOS download.

Select your country and click "Get" to receive a message containing the verification code. Enter the verification code and select "Enter". When you turn on the fan heater for the first time, the Wi-Fi LED blinks; Reset the Wi-Fi by pressing [mode] for 3 seconds, the Wi-Fi light will blink rapidly: you can now connect the unit to the app.

A - Quick Connection via Bluetooth:

Turn on Bluetooth on your smartphone and perform the following operations.

Screenshots of the Tuya Smart mobile application interface showing steps for device connection via Bluetooth: Press "+" in the upper right corner and proceed to the next step. Press "Add". Select the 2.4 GHz Wi-Fi network and enter the password, press "Next". Wait for the connection and press "Next", the app will appear as shown below. Press to change the product name.

B - Normal Connection:

If Bluetooth is not active, follow these steps:

Screenshots of the Tuya Smart mobile application interface showing steps for device connection via Wi-Fi: Press "+" in the upper right corner and proceed to the next step. Choose small appliances and heating appliances. Select the 2.4 GHz Wi-Fi network and enter the password, press "Next". Ensure the Wi-Fi logo blinks, otherwise press and hold for 5 seconds until the Wi-Fi logo stops blinking. Press "It blinks rapidly". Wait for the connection and press "Done", the app will be displayed as shown below. Press to change the product name.

User Interface

Screenshots of the Tuya Smart mobile application user interface displaying operation status, mode selection, temperature settings, timer configuration, and weekly program setup.

When selecting P1/P2/P3 in the app, the unit will operate according to the settings shown in the manual. When manually setting P3 on the unit and selecting P3 in the app, the unit will operate according to the selected settings. You can also choose to set the configurations according to your needs by selecting the P7 weekly program in the app.

Weekly Program (P7): Set the operating time and operating temperature for each hour of each day.

Temperature Correction

Use this function to set the ambient temperature calibration for the correct ambient temperature if the reading is incorrect. Select "Temperature Calibration", adjust the temperature to the current ambient temperature and check the box. The current ambient temperature is now set. Note: to calibrate the temperature, ensure the fan heater has been running for more than 1 hour.

You can preset the temperature according to your needs and give it a name (you can keep 2 quick settings).

Remote Control

The remote control functions correspond to those of the control panel. The heating power level can only be selected via a remote control.

Use a lithium/manganese button cell battery, model no. CR2025-3V, compliant with REGULATION (EU) 2023/1542. The battery is supplied with the product; for first use, remove the plastic tab inserted in the remote control to allow it to function.

HOW TO INSERT/REMOVE REMOTE CONTROL BATTERY (see drawings below)

Open the battery door on the back of the remote control (press the back and pull the tab). Place the battery in the tab, taking care to check the correct polarity. Insert the tab into the remote control.

Diagrams illustrating the insertion and removal of the CR2025 battery in the remote control.

BATTERY WARNINGS

• Batteries must not be exposed to heat sources, such as fire, sun, or similar sources; remove batteries if they start to heat up or if the appliance is not used for a long time.
• Batteries must be correctly installed in the appropriate battery compartment.
• Dispose of batteries that have reached the end of their useful life or have been damaged in accordance with current national regulations and those listed below.
• In case of battery fluid leakage, remove all batteries, preventing the leaked fluid from coming into contact with skin or clothing. If battery fluid comes into contact with skin or clothing, wash the skin with water immediately. Before inserting new batteries, clean the battery compartment completely with a paper towel or follow the battery manufacturer's recommendations for cleaning.
• Improper use of batteries can cause liquid leakage, overheating, or explosion. This liquid is corrosive and can be toxic. It can cause burns to the skin and eyes and is harmful if swallowed.
• To reduce the risk of injury:
• Keep batteries out of the reach of children.
• Do not heat, open, puncture, cut, or throw batteries into fire.
• Do not mix old and new batteries or batteries of different types.
• Do not leave metal objects that can come into contact with battery terminals and therefore may heat up and/or cause burns. Remove the plastic tab inserted in the remote control to allow it to function.

Maintenance and Storage

Disposal Information

INFORMATION FOR CORRECT BATTERY DISPOSAL ACCORDING TO REGULATION (EU) 2023/1542

Replace batteries when they are depleted. At the end of their useful life, batteries must be disposed of separately from unsorted waste. They must be sent to designated local recycling centers or returned to a retailer that provides this service. Separate disposal of batteries avoids potential negative environmental and human health effects due to improper disposal and also allows their constituent materials to be recovered and recycled, resulting in significant savings in energy and resources. To highlight the obligation for separate disposal, the battery carries the symbol of a crossed-out waste bin.

WARNING FOR CORRECT DISPOSAL OF THE PRODUCT ACCORDING TO DIRECTIVE EUROPEAN 2012/19/UE

At the end of its useful life, this equipment must not be disposed of with household waste. It must be handed over to specific local separate collection centers or to distributors that provide this service. Separately disposing of electrical and electronic equipment means avoiding possible negative consequences for the environment and health derived from inadequate disposal and also allows the materials that compose it to be recycled, thus obtaining significant savings in energy and resources. To underline the obligation for separate disposal, the product features a crossed-out waste bin.

Maintenance

CAUTION: ALWAYS REMOVE THE PLUG BEFORE CLEANING OR MAINTAINING THE APPLIANCE. IMPORTANT: DO NOT IMMERSE THE FAN HEATER IN WATER.

Cleaning the external surface of the appliance: Use a soft cloth to remove dust from the heater. If the fan heater is excessively dirty, use a soft cloth dampened with water and a neutral detergent at a temperature below 50°C. Let it dry completely before using the fan heater. Do not apply corrosive detergents or solvents, such as gasoline. Do not wash the appliance with water. Do not use oils, chemicals, or other objects that could damage the surface during cleaning. Use a vacuum cleaner to remove dust from the air inlet and outlet grilles.

Storage

When not in use, store the appliance along with this manual in the original box in a cool, dry place.

Information Requirements for Local Electric Heaters

Table 3 - Annex II - Ecodesign requirements - Product information requirements REGULATION (EU) 2024/1103 OF THE COMMISSION of April 18, 2024 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for local space heaters and related independent controls and repealing Regulation (EU) 2015/1188 of the Commission.

Contact Information: ARGOCLIMA SPA - Via A. Varo, 35 - Alfianello (BS) - ITALY - www.argoclima.com

Model Identifier(s): ARGO NIVEO SMART