User Manual for MiCODUS models including: MV501G Car GPS Tracker, MV501G, Car GPS Tracker, GPS Tracker, Tracker
24 apr 2022 — If the SIM card operator doesn't have APN user and APN password, then please use this command. Normal SIM. Note: The APN information is very important, ...
File Info : application/pdf, 12 Pages, 3.66MB
DocumentDocumentR MV501G User Manual V1.0 Learn how to set up your new MiCODUS Tracker Copyright ©2022 MiCODUS | All Rights Reserved 1. Main Features 4G+2G Real-time Tracking Historical Route Playback 1000mAh Cut Off Fuel/ Resume Fuel SOS SOS Voice Monitor Geo-fence Overspeed Alarm Vibration Alarm 2.Specifications Movement Alarm ON / OFF Engine On/ OFF Alarm GPIO Cut Wire Temperature Sensor Alarm Fuel Sensor Camera Device Information Model Weight Dimensions Charging Time Battery Working Time Working Parameters Working Voltage Working Current Sleep Current Battery Capacity Working Temperature Working Humidity Working Frequency Cellular Specifications SIM Card Cellular Antenna Positioning Type GNSS Specifications GPS Antenna Cold Start Hot Start Tracking sensitivity GPS Channels Position Accuracy MV501G 150g 107mm(L) * 51mm(W) * 20mm(H) Around 7 hours Tracking Mode:1- 2 Days DC 9-95V 4V/Average 45mA 4V/less than 5mA 3.7V 1000mAh Lion Polymer battery -20¥ - 75¥ 10%-85%RH non-condensing 4G LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28/B66 2G GSM/GPRS/EDGE: 850/900/1800/1900MHz Micro SIM Card Built-in GPS+BEIDOU+LBS Built-in 32 Seconds 1 Second -162 dBm 64 5-10m 3.Wiring diagram USB OFF/ON Normal SIM Card Celluar Signal Power GNSS Signal 4. Activate Device Install the SIM card via the correct direction as below: Normal SIM LED POWER LED (RED) CELL LED (YELLOW) GPS LED (BLUE) ALL LED Event Charging Charger inserted and battery has been fully charged Charger has not been inserted Searching for network Network has been registered GPS is in fixing GPS has fixed Device is working but stopped more than 5min Device has not been turn on Device ran out of battery State Solid Dark Dark Flash every 1 second Solid Flash every 1 second Solid ALL LED TURN OFF Please get the exact correct APN name from local SIM card provider.Take the tracker to a good signal place for operation and configure the APN for it as below: SMS Command Format Reply Example Note APN,ApnName,User, Password# SET APN OK APN,orange, orange,orange# If the SIM card has APN user and APN password, then use this command. APN,ApnName# SET APN OK APN,internet# If the SIM card operator doesn't have APN user and APN password, then please use this command. Note: The APN information is very important, it must 100% correct to match with the sim card of the tracker, if you configured wrong APN, the tracker also will reply "SET APN ok" but it will can't get online! 5. Package Content GPS Main Unit MV501G x 1 Function Cable x 1 Microphone Cable x 1 SOS Button Cable x 1 Relay x 1 User Guide x 1 Temperature Sensor (Optional) x 1 Fuel Sensor (Optional) x 1 Camera (Optional) x 1 Genuine Packing Box x 1 6. Functions Explanation Please follow with the quick user guide carefully! a. Voice Monitor: * Set center number by this sms command: CENTER,A,center number# * Switch the tracker to voice monitor mode by this sms command:MONITOR# * Dial the sim number of the tracker from the center number, then the tracker will pick up the call automatically and you will can remote monitor the voice around it. For example: MV501G CENTER,A,12345678910# SET CENTER NUMBER OK MONITOR# SET MONITOR MODE OK b. Vibration Alert: This vibration alert function just work under stationary status. How to use this function: * Configure SOS numbers for the tracker by this sms command: SOS,A,1st number,2nd number,3rd number# 3 SOS numbers supports at the most * Enable the device to enter into arm mode by this sms command: ARM# For example: MV501G SOS,A,12345678910# SET SOS NUMBER OK ARM# SET ARM MODE OK SENALM,ON,1# SET VIBRATE ALARM OK * Conifgure the alarm ways by this sms command: SENALM,[A][,M]# A=ON/OFF, default: OFF; M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1 * Keep the device under stationary status more than 5min to let it enter into sleep arm mode; * Vibrate the device then the tracker will send the vibration alarm messages c. Cut Off Fuel/Resume Fuel * Set center number by this sms command: CENTER,A,center number# * Send this sms command from the center number: RELAY,A# A=0/1/2; (0: Resume Fuel; 1: Cut Off Fuel Immediately; 2: Cut Off Fuel Safely) For example: MV501G CENTER,A,center12345678910# SET CENTER NUMBER OK RELAY,1# CUT OFF FUEL OK d. Enable SOS Emergency Call * Set sos alarm numbers via this sms command: SOS,A,1st number,2nd number,3rd number# * Long press the SOS panic button 3 seconds then the emergency call will be made to the sos numbers, it will dial the numbers by turn till it is picked up For example: MV501G SOS,A,12345678910# SET SOS NUMBER OK 7. Installation Recomendation Under rear windshield Under front windshield 3 1 2 Around dashboard 1) The decice should face up to the sky. 2) Metal therma barrier of heating layer of the windshield affects the signal. 8. Troubleshooting Type Unable to connect to tracking platform Tracker shows offline Unable to locate Location drift No command reply Use Check the APN and settings. Check whrther the data service of SIM card is enabled. Check the balance of SIM card. Check whether external power is still connected. Check if the vehicle entered netword blind area. Check the balance of SIM card. Make sure the top side facing upward without metallic things shielded. Make sure it's not in area with no satellite coverage. In area with poor GNSS signal (tall building around or basement), drifting may happen. Check whether vibration happens around to trigger the accelerator. Make sure command format is correct. Vehicle may be in network blind area. Make sure SIM card is well inserted and has SMS servi. 9. Full SMS Commands List Functions Command Format APN Setting APN,Network name[,name,password]# Server Setting If set with Domain Name: SERVER,1, Domain,Port# If set with IP: SERVER,0,IP,Port# Revise the instruction password PASSWORD,[A],[B]# Check IMEI Restore factory settings Restart device IMEI# FACTORY# RESET# Explanation APN,CMNET# (if no name & Password) APN,internet,internet,internet# (if with name & Password) SERVER,1,d.micodus.net,7700# SERVER,0,47.254.77.28,7700# A=old password, six digitals, digital range: 0-9, default000000; B=new password, six digitals, digital range: 0-9 Functions Command Format TRAFFIC,ON# Internet Traffic Switch TRAFFIC,OFF# Version Inquiry VERSION# Parameter Inquiry PARAM# Check All Alarms Status ALARM# Status Inquiry STATUS# Explanation BATTERY: XX% (Built-in Battery Power Percent) NET: CLOSED (No Network) FAILED (Connecting Network or Failure) SUCCESS(Connected to Network), NONE (No GSM Signal) HIGH / MED / LOW (Signal Strength) GPS: CLOSED (GPS Module Closed) FIXED, N(Positioned and satellite number) UNFIX, 0 (Not Positioned yet) ANGLE: 20 (the data upload angle) SENSOR: ON/OFF (the status of the shake sensor) LEVEL: 3 (the sensitivity of the shake sensor) STATE: ARM/DISARM (the defense status of the device) Alarms Parameters ALARM# ID: 19172012644 (ID number of device) STATE: ARM(DISARM)(Defense status of device) SPEED: ON/OFF(alarm status); 30km/h(alarm value); 0/1/2(alarm way) SHIFT: ON/OFF(alarm status); 300m(alarm value); 0/1/2(alarm way) VIBRATE: ON/OFF(alarm status);3(sensitivity level); 0/1/2(alarm way) ACC: ON/OFF(alarm status); 0/1/2(alarm way) ; 0/1/2(0: ACC ON&OFF, 1: ACC ON; 2: ACC OFF) (alarm situation) ; POWER DOWN: ON/OFF(alarm status);2 (alarm way) LOW BATTERY: ON/OFF(alarm status);1/2/3 (alarm way) NOTE: Alarm Ways: 0/1/2 ( 0 :GPRS only, 1: SMS+ GPRS, 2 : GPRS+SMS+phone call ) Latitude&Longitude Inquiry Map URL Inquiry Address Inquiry Time Zone Setting WHERE# URL# POSITION# NOTE: Reply message's language is determined by device's language setting, if get position content failed, device will reply Google Map location link. GMT,Time zone orientation,Whole Time Zone[,Half Time Zone]# GMT,E,8# (if no half time zone) GMT,W,9,30# (if has half time zone) NOTE: Parameter : E / W0 ~ 12; 0/15/30/45 Functions Command Format ANGLEREP,[X][,A][,B]# Set The Angle Upload ANGLEREP,OFF# Mileage Statistics MILEAGE,[A],[B]# MIELEAGE# Explanation X=ON/OFF, defaultON; A=5j180 degrees, diversion angle degree, default30 degreesB=2j5 seconds, detecting time, default3 seconds, A=ON/OFF, On/Off mileage calculation, default: Off B=0j999999Mileage initial value , unitkm ; default: 0, mileage return to zero Query current mileage Add SOS Administrator Number SOS,A,1st number,2 nd number, 3rd number# Set 3 numbers at a time: SOS,A,13800138000,1380013800 1,13800138002# Set the first numberseparately: SOS,A,13800138000# Set the second number separately: SOS,A,,13800138001# Means to set 3rd number separately: SOS,A,,,13800138002# Delete SOS Administrator Number SOS,D,1st number,2nd number,3rd number# or SOS,D,1,2,3# Directly delete the number: SOS,D,13800138000# Delete 1st number: SOS,D,1# Delete 2nd number: SOS,D,2# Delete the 2nd and 3rd number: SOS,D,2,3# Add Center Number CENTER,A,center number# CENTER,A,13800138000# NOTE: Center number is only used for cutting off power & oil, it can only be set by SOS Administrator when using this command by SMS. Delete Center Number CENTER,D# Data Upload Time Interval TIMER,T1,T2# Heartbeat Packet Upload HBT,time# Sensor Sensitivity LEVEL,A# Arm Manually ARM# T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10; T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10; HBT,3# NOTE: Range :1-60min, default 3min. LEVEL,2# NOTE: ASensitivity Level 1-9 (1-9 is from week to strong vibration) Set the device into arm mode Functions Disarm manually Command Format DISARM# Explanation Set the device out of arm mode RELAY,A# Cut Off / Resume Fuel A=1/2; 1: Enable relay immediately 2: Enable relay safely [STATE] ON/OFF 1. RELAY,1# A is set to 1, the relay command will be executed immediately; 2. RELAY,2# A is set to 2, the relay command will be executed safely. The vehicle is safe only when the speed is lower than 20km/h if GPS is fixed, or the vehicle is stationary if GPS is not fixed. RELAY,0# Overspeed Alarm Setting SPEED,[A][,B][,C]# SPEED,OFF# Vibration Alarm Setting SENALM,[A][,M]# SENALM,OFF# Shift Alarm Setting SHIFT,[A][,B][,M]# Auto Arm By ACC SHIFT,OFF# ACCARM,ON,M# ACCARM,OFF# ACC Status Change Alarm ACCALM,ON,A# ACCALM,OFF# A=ON/OFF, open or close over speed alarm, defaultOFF B=1j255(km/h), speed limit, default100(km/h); C=0/1, way of alarm, 0 : GPRS only, 1: SMS+GPRS, default1. A=ON/OFF, default: OFF; M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+GPRS, 2 : GPRS+SMS+phone call, default:2 Example: SHIFT,ON,100,1# ( Means Setting 100 meters shift alarm range, when the ignition turned off, vehicle's 100 meters' shift will trigger the alarm. ) A=ON/OFF; default:ON B=Shift Distance (Range: 100-9999m) M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+CALL, default:1 Arm Time: M=5-1800s, default: 60s Close auto arm function Alarm Ways A=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+CALL, default:1 Cancel ACC alarm function Functions Command Format Power Disconnect Alarm PWRALM,A,B# PWRALM,OFF# SOS Alarm SOSALM,A,B# SOSALM,OFF# Voice Monitor/Track Modes Switch MONITOR# TRACK# Explanation A=ON/OFF, default ON; B=0/1/2/3, ways of alarming, 0: GPRS only, 1: SMS+GPRS, 2 : GPRS+SMS+phone call, 3GPRS+ call, default:2 Close power disconnect alarm A=ON/OFF, default ON; B=0/1/2/3, ways of alarming, 0: GPRS only, 1: SMS+GPRS, 2 : GPRS+SMS+phone call, 3GPRS+ call, default2 Close SOS alarm function NOTE: Before monitoring the voice around the device, the user must change the device to this monitor mode firstly. NOTE: After used the voice monitor mode, user can switch the device back to track mode by this command. 10. Any Questions? E-mail: support@micodus.com Skype: MiCODUS 11. Download the APP Search "MiCODUS" in iOS APP store or Google Play Store, or just scan the QR code as below to download MiCODUS APP: Download on the APP Store Download for Android