VEVOR Magnetic Sweeper USER MANUAL

Product Overview

The document displays images of the VEVOR Magnetic Sweeper models: QJ8038/QJ8039 and QJ8010.

Contact Information

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate: www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.

General Instructions and Warnings

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

This manual provides important information on proper operation & maintenance. Every effort has been made to ensure the accuracy of this manual. These instructions are not meant to cover every possible condition and situation that may occur. We reserve the right to change this product at any time without prior notice.

IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE, DO NOT OPERATE THIS PRODUCT!

[Warning] KEEP AWAY FROM MATERIALS AND COMPONENTS THAT CAN BE DAMAGED BY EXPOSURE TO MAGNETS. INDIVIDUALS WITH PACEMAKER SHOULD CONSULT PHYSICIAN BEFORE USING THIS PRODUCT.

Model and Parameters

Assembly and Use

Note: Please remove the protective film on the surface of the aluminum housing before use to avoid weakening the magnetic force.

QJ8010 Assembly: An image shows the magnetic wheel component.

QJ8038 and QJ8039: An image shows a locking ring component. A diagram illustrates the use of two locking rings to secure an extended tube, with red arrows indicating tightening points. Tightening the Locking ring can keep the tube stretched in the position shown when the tube is loose due to too much use.

OPERATION

1. Adjust the extension handle to the desired height. Roll the Magnetic Sweeper across the desired hard surface area. It can pick up nails, pins, bolts and any other magnetic object.
2. Lift the release lever to quickly remove the magnetic force, allowing the adsorbed nails to fall off quickly, easily and conveniently. Avoid injury by removing sharp nails by hand.

Safety Instructions

WARNING:

1. Please do not put it near flammable materials.
2. DO NOT SIT, STAND ON THIS ITEM. It is forbidden to carry people at any condition.
3. Overload is strictly prohibited.
4. Don't move too fast when passing potholes areas.
5. This product is not a toy. Do not allow children to play with or near this item.
6. Do not lift while loaded.
7. Use as intended only.
8. Inspect before every use; do not use if parts are loose or damaged.

Assembly Precautions

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the influence of alcohol, drugs or medication.
6. Assemble on a flat, level, hard and smooth surface capable of safely supporting a fully loaded Sweeper.

SAVE THESE INSTRUCTIONS

Troubleshooting

Maintenance

1. Avoid prolonged exposure to the sun to avoid aging.
2. Avoid the cart from cracking due to violent impact when going uphill and downhill.

Manufacturer and Importer Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC REP: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK REP: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX