Manuals+

SD7K ASSEMBLY INSTRUCTIONS

CAUTION! As a by-product of the manufacturing process, occasionally some metal shavings or burs will unavoidably remain. To avoid injury, please watch your fingers when adjusting clamps, or when working around pipe-ends and screw-ends.

INSIDE THIS PACKAGE

Before assembly, please make sure that all the items listed below are present.

  • Cymbal 3pcs: 3 Cymbal Pads
  • Kick Pad: Kick Pad
  • Drum Pads: Snare Pad
  • Drum Pads: 2 Tom Pads
  • 2 Metal Rods
  • Accessories:
    • Cymbal Holder (Short)
    • 2 Drumsticks
    • AC Adaptor
    • Metal Rod
    • 9 Connecting Cables
    • Hexagon Key (5mm)
    • Instruction Manual
    • Drum Key
    • Assembly Instructions
  • 2 Cymbal Holders (Long)
  • Side Arm (L1)
  • Side Arm (L2)
  • Side Arm (R)
  • Pillar (L)
  • Pillar (R)
  • Center Pipe (2)
  • Leg (L)
  • Leg (R)
  • Center Pipe (1)
  • Drum Module
  • Hi-Hat Pedal / Hi-Hat Control Pedal

I. SETTING UP THE FRAME OF THE DIGITAL DRUM KIT

Diagram 1: Left Leg Assembly

This diagram illustrates the assembly of the left leg structure.

  1. Attach the Pillar (L) to the clamp on the Leg (L).
  2. Using the drum key, tighten the screws on the clamp.
  3. Remove the screw attached to the connector.
  4. Attach the cross pipe to the connector.
  5. Re-attach the screw into the connector.
  6. Tighten the screw on the connector.

Diagram 2: Right Leg Assembly

This diagram illustrates the assembly of the right leg structure.

  1. Attach the Pillar (R) to the clamp on the Leg (R).
  2. Tighten the screws on the clamp.
  3. Remove the screw attached to the connector.
  4. Attach the cross pipe to the connector.
  5. Re-attach the screw into the connector.
  6. Tighten the screw on the connector.

Diagram 3: Connecting Center Pipe (1)

This diagram shows connecting the first center pipe to the left leg assembly.

  1. Attach Center Pipe (1) to the clamp on the Left Leg Assembly.
  2. Tighten the screws on the clamp.

Diagram 4: Attaching Right Leg Assembly to Center Pipe (1)

This diagram shows attaching the assembled right leg structure to the center pipe.

  1. Attach the Right Leg Assembly to the Center Pipe (1).
  2. Tighten the screws on the clamp.

Diagram 5: Connecting Center Pipe (2)

This diagram shows connecting the second center pipe to the left leg assembly.

  1. Attach Center Pipe (2) to the clamp on the Left Leg Assembly.
  2. Tighten the screws on the clamp.
  3. Attach the Right Leg Assembly to the Center Pipe (2).
  4. Tighten the screws on the clamp.

Diagram 6: Attaching Side Arm (L1)

This diagram shows attaching the left side arm to the left pillar.

  1. Attach the Side Arm (L1) to the clamp on the Pillar (L).
  2. Tighten the screws on the clamp.

Diagram 7: Attaching Side Arm (L2)

This diagram shows attaching the second left side arm to the left pillar.

  1. Attach the Side Arm (L2) to the clamp on the Pillar (L).
  2. Tighten the screws on the clamp.

Diagram 8: Attaching Side Arm (R)

This diagram shows attaching the right side arm to the right pillar.

  1. Attach the Side Arm (R) to the clamp on the Pillar (R).
  2. Tighten the screws on the clamp.

2. ATTACHING THE DRUM PADS

This section details how to attach the drum pads to the frame.

  1. Loosen the Wing Nuts on the drum pads.
  2. Remove the Metal Rods.
  3. Re-attach the Metal Rods to the drum pads.
  4. Tighten the Wing Nuts.
  5. Attach the drum pads assemblies to the holder clamps and adjust their position, then tighten the wing nuts on the Holder clamps. Repeat for other pads.

Visual description: This involves connecting drum pads (Snare, Tom) to holder clamps on the frame using metal rods and securing them with wing nuts.

3. ATTACHING THE CYMBAL PADS

This section details how to attach the cymbal pads.

  1. Attach the Cymbal Holders to the Cymbal Holder clamps on the Side Arms.
  2. Tighten the Wing Nuts on the Holder clamps.
  3. Remove the Wing Nut and the Felt Washer of each Cymbal Holder.
  4. Attach the Cymbal pads to the Cymbal Holders.
  5. Re-attach the Felt Washer and Wing Nut, then tighten the Wing Nut of each Cymbal Holder. Repeat for other cymbals.

Visual description: This involves mounting cymbal holders onto the frame's side arms, preparing them by removing wing nuts and felt washers, attaching the cymbal pads, and then securing them with the felt washer and wing nut.

4. ATTACHING THE DRUM MODULE

This section details how to attach the drum module.

  1. Attach the Metal Rod to the Drum Module.
  2. Tighten the Wing Screw securely on the Drum Module.
  3. Attach the Metal Rod to the Holder Clamp on the Side Arm (L1) and adjust the position.
  4. Tighten the Wing Nut on the Holder Clamp.

Visual description: A metal rod is attached to the drum module, secured with a wing screw. This rod is then attached to a holder clamp on the left side arm and tightened with a wing nut.

5. CONGRATULATIONS

You've successfully assembled your new Simmons SD7K electronic drum kit.

You can now attach your own bass drum pedal to the kick pad. Also, be sure to attach the clearly marked cables from the pads to the correct inputs on the drum module.

For connection instructions and more information on your new kit, please refer to the User Manual or visit www.simmonsdrums.net.

PDF preview unavailable. Download the PDF instead.

SD7K Assembly Adobe PDF Library 7.0 Adobe InDesign CS2 (4.0.4)

Related Documents

Preview Simmons SD200 Electronic Drum Kit Owner's Manual
This manual provides comprehensive instructions for setting up, operating, and maintaining the Simmons SD200 Electronic Drum Kit. It covers safety precautions, assembly, module operation, connections, and troubleshooting.
Preview Simmons SD200 Electronic Drum Kit Owner's Manual
Comprehensive guide for the Simmons SD200 Electronic Drum Kit, covering safety instructions, assembly, module operation, connections, advanced features, presets, specifications, and warranty information.
Preview Simmons Titan 70 Electronic Drum Kit Owner's Manual
Comprehensive owner's manual for the Simmons Titan 70 Electronic Drum Kit, covering setup, connections, operation, features, and maintenance.
Preview Simmons SD5X Electronic Drum Kit User Manual
User manual for the Simmons SD5X Electronic Drum Kit, providing setup, operation, and maintenance instructions for this digital drum set. Learn about controls, patterns, kits, voices, and more.
Preview Simmons Titan 20 Electronic Drum Kit Owner's Manual
Comprehensive owner's manual for the Simmons Titan 20 Electronic Drum Kit, covering setup, operation, features, and maintenance.
Preview Simmons SD2000 Electronic Drum Kit Owner's Manual
Comprehensive owner's manual for the Simmons SD2000 5-Piece Electronic Drum Kit. Learn about features, assembly, operation, and maintenance.
Preview Simmons SD1250 Firmware Release Notes
Release notes detailing firmware updates for the Simmons SD1250 electronic drum module, including bug fixes and feature improvements.
Preview Simmons 4-in-1 Convertible Crib Assembly Instructions and Safety Tips
Comprehensive guide for assembling the Simmons 4-in-1 Convertible Crib, including essential safety tips for baby and furniture. Learn how to safely use and maintain your crib.