Q-TRAN LALO Linear Fixture Instruction Manual

Instruction Manual for Q-TRAN models including: LALO, Linear Fixture, LALO Linear Fixture, Fixture

LALO-ENCAPSULATED (03) Applications/Install

Technical - IES Files, CAD files, Specs | Q-Tran

LALO-FLAT (01) Applications/Install

LALO-OPTICS (02) Applications/Install

File Info : application/pdf, 10 Pages, 5.63MB

INSTALL-FXT-LALO ?d=112202385625

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO

LALO-FLAT (01)

LALO-OPTICS (02)

LALO-ENCAPSULATED (03)

COMPLIANT

5YEAR WARRANTY

METHODS & INSTALLATIONS

COMPONENTS & HARDWARE

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO
ATTENTION: Please read all instructions BEFORE installation
· Product to be installed by a licensed electrician - Field modifications void warranty · Use only with Class 2 power supply unit -- Compatible for use with Q-Tran power supplies · Surface mount or recessed in millwork · Suitable for installation in storage area of a clothes closet when assembled as a finished fixture up to 4W/ft at Q-Tran facility · Not rated for walkover · Input Voltage: 24VDC · Diagrams for representation only and not to scale.

METHODS OF INSTALLATION: LALO can be recessed in millwork with all compatible LED strips except SW-HE24/9.0.

832 .21"

Stainless Steel Mount

CEILING

.81

1.25

.20

.625"

SST-01

#4 x 5/8" Flat Head SS

Magnet Mount

.26"
WALL

.64"
2.5"
12" .23" .75"
MMA-01 Sold separately

1.25"

.81"
.20" .20"
.625"

MG-01

#6 x 5/8" Flat Head SS

Adhesive Mount

WALL

CONCRETE

Silicone Sold separately

VHB Tape Sold separately

FLOOR

Not rated for walkover

WALL
0.85"

Additional Mounting
(Sold separately) Q-ANGLE
1.38"
2.23"
1.50" 1.93"
Q-PIVOT
0.75"
1.03"

HINGE BRACKET

HMB-M HMB-L HMB-XL

1.41" 0.71" 1.46" 1.29" 1.46"

4.00"

Surface Mounting Method · VHB Mount (page 5-6) · Silicone Mount (page 7) · Screw Mount (page 8) · Magnet Mount (page 9)

Recessed Mounting Method · Magnet Mount : Millwork (page 10)

Cove, Under & over cabinet:
Ideal for office, retail, hospitality, education, laboratory, and residential.

Shelf:
Ideal for office, retail, hospitality, education, laboratory, and residential.

Display cabinet:
Ideal for retail and hospitality.

Signage:
Ideal for lobby, retail, hospitality, institutional, and transportation.

WIRING OPTIONS

MOUNTING

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO

METHODS & INSTALLATIONS

COMPONENTS & HARDWARE

WIRING OPTIONS

.42" .56" .70"
LALO-FLAT (01)

.42"

.54"

.70"
LALO-OPTICS (02)

.42" .56" .70"
LALO-ENCAPSULATED (03)

COMPONENTS & HARDWARE
STAINLESS STEEL CLIP

1.25"

.81"

.20"

SST-01

Included

.625"

Flat Head Screw

#4x5/8"

MAGNET CLIP

1.25"

.81" .20"

.20"

MG-01

.21"
0.85"

MAGNET MOUNT ACCESSORY; sold individually

.23" .75"

.64" 2.5"
12"

MMA-01

Included
· 2 #6x5/8" Flat Head SS

ACCESSORIES SOLD SEPARATELY

HINGE BRACKET; sold individually

Q-ANGLE; sold in pairs

Image shows HMB-M
HMB-M HMB-L HMB-XL

Included
· 3/4" long mount screw · 1/4" #4 clip mount
screw

1.38"
2.23"
1.50" 1.93"
Q-ANGLE

Included
· 4 SS #6x1.25" Flat head wood screws
· 2 SS 4-40 Flat head clip screws
· 2 SS 6-32 Fillister screws

Q-PIVOT; sold in pairs

0.75"
1.03"
Q-PIVOT

Included
· SS #4-40x3/16 Flat head screws
· 2 #4x3/4 Pan Head screws

ADHESIVE SOLD SEPARATELY

SILICONE

VHB TAPE; sold in 15' increments

832 DOWSIL 832

TAPE-VHB-IP20

STAINLESS STEEL CLIP · 2 clips provided for 4' or less; 4 clips provided for greater than 4'

NOTES:

MAGNET CLIP

· One magnet clip per foot

· MMA-01 comes in 12" pieces; use at least one clip per MMA-01 accessory

· MMA-01 can be cut into smaller pieces, if desired

MOUNTING

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO
CONTINUOUS WIRING CONFIGURATION OPTIONS

S1
.08"
P1
.08"

.16"

Review wire method to ensure clean installation prior to mounting finished fixture.
NOTE: Additional wire methods include: S1, S2: Connector/Wire Input only P1, P2: Connector/Wire Input and Output

METHODS & INSTALLATIONS

COMPONENTS & HARDWARE

WIRING OPTIONS

MOUNTING

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO
SURFACE MOUNTING METHOD SURFACE PREPARATION

50/50 alc
5 mins

70-100ºF

50% humidity or less

72 hrs

Temperature and environmental concerns:
· Ideal application environment is 70-100ºF in 50% humidity or less.
· Minimum application temperature: 50ºF
· This temperature and humidity should be maintained for 72 hours after application for maximum bond strength.

b.
a. Using a 50/50 alcohol mix, thoroughly clean the backside of the Fixture and the surface area where Fixture will be installed. Allow 5 minutes to dry. b. Peel back 0.5" of the VHB tape's protective film on one end and use firm pressure to adhere it to the desired surface, avoiding air bubbles. Continue peeling the film and adhering the tape in small sections until the entire length is installed.

METHODS & INSTALLATIONS

COMPONENTS & HARDWARE

WIRING OPTIONS

MOUNTING

2 layers 1 layer

Wood

Brick

Concrete

Paint or 3M
Primer 94

For porous materials (Wood, Brick, Concrete etc.) apply two layers of paint or primer to the surface. This will help create a better bonding surface for these materials. These can be purchased from a local hardware store.

MATERIALS
Concrete, Stone, Cinderblock, Metal, and Brick ABS, Fiberglass, Plastic, and PVC
Tile, Wood, Ceramic, Glass, or Metal
All Purpose

SUGGESTED EPOXIES
Loctite Metal and Concrete Two-Part Epoxy
Loctite Plastic Two-Part Epoxy
Loctite Clear Two-Part Epoxy
Strong Stik

METHODS & INSTALLATIONS

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO
SURFACE MOUNTING METHOD: VHB ADHESIVE MOUNT
BEFORE installation, the surface must be thoroughly cleaned and dried for maximum bond strength. (page 5)

Marker

Length as needed

28 29 30 31

Length as needed
Determine the LALO fixture(s) location and positioning on desired surface before adhering Fixture to surface. Make any necessary reference markings to indicate fixture placement.

2
a.
b.
a. To adhere the VHB adhesive, peel the white film back while evenly applying the tape to the mounting side of the fixture. The red side should be visible.
b. Remove the red film and position fixture in place according to your previous reference marking(s).

COMPONENTS & HARDWARE

WIRING OPTIONS

MOUNTING

Remove protective film from the surface of the fixture's lens.

NOTES: EPOXY ALTERNATIVE: For improved bonding strength, apply a small amount of epoxy at each end. Refer to table on page 5 for suggested epoxies. These can be purchased at a local hardware store. Please follow all manufacturer instructions for suggested epoxy.

METHODS & INSTALLATIONS

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO
SURFACE MOUNTING METHOD: SILICONE · 2 clips provided for 4' or less; 4 clips provided for greater than 4'

Marker

24" - 30"

28 29 30 31

24" - 30"

Determine the LALO fixture(s) location and positioning on desired surface; evenly distribute clips. Make any necessary reference markings to indicate where each clip is to be secured in place. Recommended every 24" - 30".

24" - 30"

832
a.
a. Firmly press the silicone-coated clips on the marked reference points.
b. Wait for silicone adhesive to cure completely before snapping fixture into place.
c. Snap fixture onto clips. NOTE: Cure time is dependent on the type of silicone adhesive used.
Refer to silicone product manufacturer for accurate drying time.

COMPONENTS & HARDWARE

WIRING OPTIONS

MOUNTING

Remove protective film from the surface of the fixture's lens.

METHODS & INSTALLATIONS

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO
SURFACE MOUNTING METHOD: SCREW MOUNT · 2 clips provided for 4' or less; 4 clips provided for greater than 4'

Marker

24" - 30"

28 29 30 31
b.

24" - 30"

a.
a. Secure clips using the #4 flat head hardware provided. b. Ensure the screw head is flush with the clip's base. c. Snap fixture onto clips.
NOTE: Flat head screw type is dependent on surface/application material. Alternative flat head screws may be required. Refer to the surface material manufacturer for suggested screw type.

COMPONENTS & HARDWARE

WIRING OPTIONS

MOUNTING

Remove protective film from the surface of the fixture's lens.

METHODS & INSTALLATIONS

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO

SURFACE MOUNTING METHOD: MAGNET MOUNT
· One magnet clip per foot · MMA-01 comes in 12" pieces; use at least one clip per MMA-01 accessory · MMA-01 can be cut into smaller pieces, if desired

Marker

Length as needed

28 29 30 31

2
c. b.
a.

Determine the LALO fixture(s) location and positioning on desired surface. Make any necessary reference markings to indicate where the magnet mount accessory bracket is to be secured in place.

a. Mount the two #6 flat head screws into the 12" magnet mount accessory bracket through the slotted holes at each end. Ensure the screw head is flush with the magnet mount bracket.
b. Snap the magnet clips onto the backside of the fixture. They should be offset to the accessory bracket screws to maximize magnetic connection.
c. Place the assembled fixture into the magnet mount bracket.
NOTE: If surface application requires a longer screw, the screw size must be a #6 Flat Head.

COMPONENTS & HARDWARE

WIRING OPTIONS

MOUNTING

Remove protective film from the surface of the fixture's lens.

METHODS & INSTALLATIONS

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO

RECESSED MOUNTING METHOD: MILLWORK
· One magnet clip per foot · MMA-01 comes in 12" pieces; use at least one clip per MMA-01 accessory · MMA-01 can be cut into smaller pieces, if desired · LALO can be recessed in millwork with all compatible LED strips except SW-HE24/9.0

.85"

.68" .20"

Length as needed .04"

Marker

28 29 30 31

Image shows with FLAT Lens

24" - 30"

Determine the LALO fixture(s) location and positioning on desired surface. Make any necessary reference markings to indicate where the magnet mount accessory bracket is to be secured in place.
NOTE: Depth of the channel in the millwork is dependent on overall height with the magnet clip and Magnet Mount Accessory.

a.
a. Mount the two #6 flat head screws into the 12" magnet mount accessory bracket through the slotted holes at each end. Ensure the screw head is flush with the magnet mount bracket.
b. Snap the magnet clips onto the backside of the fixture. They should be offset to the accessory bracket screws to maximize magnetic connection.
c. Place the assembled fixture into the magnet mount bracket. NOTE: If surface application requires a longer screw, the screw size must
be a #6 Flat Head.

COMPONENTS & HARDWARE

WIRING OPTIONS

MOUNTING

Remove protective film from the surface of the fixture's lens.

References

Adobe PDF Library 17.0 Adobe InDesign 18.1 (Windows)