Sonoff ZBMINIR2 Zigbee Smart Switch User Manual

Introduction

This is an extremely compact Zigbee 3.0 single-channel neutral wire switch, capable of being installed in a mounting box and supporting a maximum load of 10A, thus making ordinary switches smart. It supports a repeater function to easily improve Zigbee communication quality and can also link with other devices in smart scenarios to realize your home automation.

• Remote Control

• Timer Schedule

• Voice Control

• Smart Scene

Features

• Power-on State

• Inching Mode

• Relay function

• Group Control

Device Overview

① Button

• Single press: Turn on/off the smart device.
• Press and hold for 5 seconds: Device enters the pairing mode. (Pairing time 10 minutes)
• Click three times in succession: Switch the external switch type.

② LED Indicator (Green)

• Flash slowly for 180 seconds: First-time power on/Device is in pairing mode.
• Steady on: Normal connection with the gateway.
• Slow flash: The device is in pairing mode.
• Fast flash: Abnormal connection with the gateway.
• Flashes three times quickly: Switch the external switch trigger type.

Compatible Voice Assistants

Supports Google Home and Amazon Alexa.

Specification

*This product is only suitable for safe use at altitudes below 2000m.

Installation

1. Power off
2. Wiring Instruction

   It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order to avoid damaging the equipment and causing danger.

   Make sure all wires are connected correctly.

   Supported switches are rocker switch and push button and factory default by supporting rocker switch.

Warning: Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!

Add Device

1. Download the eWeLink App & Add SONOFF Zigbee Gateway

   Please download the "eWeLink" App from Google Play Store or Apple App Store.

2. Scan QR code to add the device.
   1. Enter "Scan"
   2. Scan the QR code on the device
   3. Select "Add Device"
   4. Power on the device
   5. Long press the button for 5 seconds
   6. The LED indicator flashes slowly for 180s
   7. Select Zigbee gateway
   8. Wait until the addition is done

Matched Gateways

Recommended SONOFF gateway models: ZBBridge–P, NSPanel Pro, iHost, ZBBridge-U

Other compatible SONOFF gateway models: ZBDongle–P, ZBDongle-E

Third-party compatible gateway models:

• Amazon Gateway Model: Echo Plus 2nd, Echo Show 2nd, Echo 4th Gen
• Samsung Gateway Model: SmartThings hub V3

*Other gateways supporting ZigBee3.0 wireless protocol. Detailed information is in accordance with the final product.

Install the MINI Extreme in the mounting box.

Factory Reset

Trigger conditions (any one condition met):

• Press and hold the device button for 5 seconds.
• Quickly press the external switch 10 times (except for the external switch type, all other settings will be restored to factory defaults).
• Delete the device on eWeLink.

FCC Compliance Statement

1.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1)This device may not cause harmful interference, and
• (2)This device must accept any interference received, including interference that may cause undesired operation.

2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement: The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

ISED Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

• (1)This device may not cause interference.
• (2)This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003(B).

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

• (1)L'appareil ne doit pas produire de brouillage;
• (2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Cet appareil numérique de la Classe B conforme à la norme NMB-003(B) du Canada.

Cet appareil est conforme à la norme RSS 247 d'Industrie Canada. Le fonctionnement est soumis à la condition que cet appareil ne provoque pas d'interférences nuisibles.

ISED Radiation Exposure Statement This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

EU Declaration of Conformity

Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type ZBMINIR2 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/compliance/

For CE Frequency

WEEE Disposal and Recycling Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

RACCOLTA DIFFERENZIATA

Verifica le disposizioni del tuo Comune.

Separa le componenti e conferiscile in modo corretto.