Aspes AVP401600OBA 16" Stand Fan

Introduction

Read this manual carefully and keep it for future reference.

General Safety Instructions

• To protect against electric shock, do not immerse the cord, plug, or any part of this unit in water or other liquids.
• Close supervision is necessary when the unit is used by or near children.
• Unplug the unit from the power supply when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the fan.
• Do not use the unit if the cord or plug is damaged, or after the unit malfunctions, or has been dropped or damaged in any way. Return the unit to the nearest authorized service center for examination, repair, or adjustment.
• The use of accessories not recommended by the manufacturer may cause injuries.
• Always attach the plug to the unit first, then plug the cord into the power outlet. To disconnect, turn all controls to the "off" position and then unplug the unit from the power supply.
• Do not use the unit for any purpose other than its intended use.
• Never use the unit with a damaged power cord. If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.
• Do not attempt to repair the unit yourself. Contact our service center for replacement or repair.

Ventilation appliances should not be used by children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have received instructions or supervision from a responsible adult.

Children under 8 years of age and persons with reduced physical, sensory, or mental capabilities, or persons without experience or knowledge, should not use the unit without adult supervision or prior instruction.

Keep the appliance and its cord out of reach of children under 8 years old.

? Do not insert fingers or any other object through the protective grille while the fan is operating, as the blades could cause severe injury.

Assembly Instructions

1. Insert the plastic pointers (22) into the end of the cross foot pipes (21).
2. Secure the support tube (11) to the cross base (21) using the 4 "A" screws (12).
3. Insert the foot cover (10) through the support tube to the lowest part.
4. Extend the extension tube (8) and then tighten it with the height adjustment ring (9).
5. Place the motor and button assembly over the extension tube (8) and then tighten the "B" screw (7).
6. To finish, install the rear grille by tightening it with the adjusting nut (15), then set the blades (2) and tighten them with the nut (16). Install the center plate (20) on the front grille (1) using the 3 screws (18) and their washers (19). Attach the front grille (1) to the rear grille (3) using the securing clips (17).
7. To adjust the direction and height, loosen the height adjustment ring (9) and then extend the extension tube (8) to the desired height. Then adjust the height adjustment ring (9) again. You can also adjust the tilt of the motor to the desired angle by means of the hinged motor assembly.
8. If the blades vibrate too much, try to orient them, rotating them a bit, and then retighten them.
9. Do not insert fingers or any other object into the grids; the rotation of the blades could cause severe injury.

Maintenance and Cleaning

Before cleaning, disconnect the unit from the power supply. Remove the front guard. Use a damp cloth to clean oil stains. Please do not hit the blades or alter their angles.

Technical Data

220-240V 40W 50Hz

Environmental Protection Guidelines

♻️ This appliance should not be disposed of with household waste at the end of its service life. It must be offered at a central recycling point for electrical and electronic domestic appliances. This symbol on the appliance, instruction manual, and packaging draws your attention to this important issue.

The materials used in this appliance can be recycled. By recycling used domestic appliances, you contribute significantly to environmental protection. Consult your local authorities for information regarding the collection point.

Contact Information

Website: www.aspes.es

Email: aspes@sareteknika.es

Phone: 902 99 69 01 / 944 04 14 08