GX10 Bluetooth Intercom

One-Key-Networking of Multiple GX10s

Automatic pairing steps (for 6 GX10 units):

1. Power on all 6 GX10 intercoms. Hold the M buttons to activate passive pairing mode. The red and blue lights will flash quickly and alternatively.
2. Press the Multifunction button of any unit (e.g., Unit No.1). The red and blue lights will flash slowly and alternatively. Unit No.1 will enter automatic pairing mode with a 'pairing' voice prompt.
3. After successful pairing, a 'Device Connected' voice prompt will be heard.

Music Sharing (between 2 GX10 Units)

How to turn on

Music sharing is unidirectional. To share music from GX10 A to GX10 B:

1. Connect GX10 A to your phone via Bluetooth. Open a music player and keep the music in pause state.
2. Pair and connect GX10 A to GX10 B (ensure both are in non-intercom mode).
3. After successful pairing, press and hold the Bluetooth Talk and M buttons of GX10 A for 3 seconds. Slow flashing blue lights and a 'Start Music Sharing' voice prompt indicate successful sharing.

How to turn off

In music sharing state, press and hold the Bluetooth Talk and M buttons of GX10 A for 3 seconds. A 'Stop Music Sharing' voice prompt will be heard.

EQ Sound Settings

In music playback state, press the M button to enter EQ settings. Each press cycles through sound effects: Middle Range Boost, Treble Boost, and Bass Boost, announced by voice prompts.

Additional Features

Voice Control

In standby state, press the M button to enter voice control mode. The blue light will flash slowly.

Last Number Redial

In standby state, press the Multifunction button twice to redial the last number called.

Factory Reset

In power on state, hold the Multifunction, Bluetooth Talk, and M buttons for 5 seconds. The red and blue lights will remain on for 2 seconds.

Battery Level Prompt

In standby state, press the Bluetooth Talk and M buttons. A voice prompt will announce the current battery level, including a low battery warning.

Flowing Light Mode

In Bluetooth standby state, hold the M and Volume up buttons for 2 seconds. The red flowing light flashes twice when turning on/off.

Colorful Light Mode

In Bluetooth standby and flowing light on state, press the M and Volume up buttons to switch between colors in order.

Installation (2 Methods)

Method 1: Install with the adhesive mount

1. Install the intercom into the mount.
2. Attach the double-sided adhesive to the mount.
3. Install the intercom with adhesive onto the helmet.

Quick removal of the intercom on the helmet

Unplug the headset, hold the intercom with fingers, then push up to remove it from the helmet.

Method 2: Install with the clip mount

1. Install the metal clip onto the mount.
2. Install the intercom onto the mount.
3. Clip the mount onto the helmet.

Quick removal of the intercom on the helmet

Unplug the headset, hold the intercom with fingers, then push up to remove it from the helmet.

GX10 Parts & Accessories

• Intercom x1
• Microphone & Speaker Set x1
• Mount x1
• Single/Double Sided Adhesives x1
• Metal Clip x1
• Speaker Fasteners x4
• USB Cable x1
• Rectangular Fasteners x2
• Manual x1

Charging Instructions

1. Before use, charge the Bluetooth intercom using the provided cable. Plug the USB Type-C connector into the intercom's charging port. Connect the USB A connector to a power source:
   • A USB A port on a PC
   • A DC 5V USB output on a power bank
   • A DC 5V USB output on a power adapter
2. The indicator light is always-on red while charging and turns off when fully charged. Charging from low battery to full takes approximately 1.5 hours.

Parameter

Precaution

1. If the intercom is unused for over one month, charge it every two months to protect the lithium battery.
2. The applicable storage temperature is -20 °C to 50 °C. Avoid storing in extreme temperatures to prevent affecting the product's service life.
3. Do not expose the product to open fire to avoid explosion.
4. Do not attempt to open the device yourself to prevent short circuits or battery damage.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.