TP-Link Product Support - Wireless Networking Equipment Support
User Guide for tapo models including: S500D Smart Wi-Fi Dimmer Switch, S500D, Smart Wi-Fi Dimmer Switch, Wi-Fi Dimmer Switch, Dimmer Switch, Switch
Support | Tapo
Download for Tapo S500D | TP-Link
File Info : application/pdf, 2 Pages, 310.76KB
DocumentDocumentProduct Introduction Tapo smart dimmer switch turns on and dims the lights automatically, saving you effort and electricity bills. Wire Your Switch 1 Turn off the circuit breaker. Then remove the old wallplate of the wall switch and label the Ground and Neutral wires. 3 Identify Line and Load wires. 1) Turn on the circuit breaker. Use a voltage detector to identify the energized wire (Line wire). Take care to avoid electric shocks. 4 Connect the wires to the smart dimmer switch as shown below. To Light 5 Line up the switch with the mounting holes. Secure it with screws. 6 Attach the wallplate and turn on the circuit breaker. Then the wiring is finished. Ground: Usually green or copper. Neutral: Usually white and not connected to the dumb switch. Line: Usually black and coming from the circuit breaker. Load: Usually black. One end is connected to the light. If you are unsure, consult a qualified electrician. 2 Disconnect the wires from the old switch. Line wire Load wire 2) Turn off the circuit breaker. Label the Line and Load wires. Power Source Flip the page over to complete setup. Set Up Your Switch STEP 1 DOWNLOAD APP Get the Tapo app from the App Store or Google Play. OR Appearance STEP 2 SET UP Tap the button in the app. Select Switches and then your model. Follow the step-by-step app instructions to set up your smart switch. Reset Brightness Indicators Decrease/Increase Brightness On/Off Button LED Restart Button Explanations / Reset Restart Decrease or increase the brightness. Press and hold for about 5s to reset Wi-Fi while keeping other settings. Press and hold for about 10s to restore your switch to factory default settings. Press to restart your switch. LED Status Solid amber Blinking amber & green Starting up; disconnected from cloud. Ready for setup. Blinking green Stay green for 30s Solid red Blinking amber White Blinking green slowly Connecting to Wi-Fi. Connected to Wi-Fi. Disconnected from Wi-Fi. Device resetting. Light fixture is off. Firmware upgrading. Specifications Rating: 120 V~ 60 Hz Load: 300 W Incandescent, 150 W LED Operation temperature: 0~40 Method of mounting included: Independently mounted (Vertically position only); Operating control, Type 1 action Pollution Degree 2, Rated Impulse Voltage 2500 V Software Class A, NEMA Type 1.Y CAUTION High Voltage-Disconnect power supply before servicing MISE EN GARDE Haute tension. Débrancher l'alimentation électrique avant d'utiliser Safety Notice Before installing, servicing or removing the switch, read and follow all safety precautions including the following: · CAUTION Risk of Electric Shock More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off. · The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements, or are uncomfortable performing the installation, consult a qualified electrician. · Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces. · Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm). · Tighten terminal screws to 13 lbf-in. ? Need some help? Visit www.tp-link.com/support for technical support, user guides, FAQs, warranty and more information. Quick Start Guide Smart Wi-Fi Dimmer Switch ©2022 TP-Link 7106509851 REV1.0.0 *Images may differ from your actual product.