PS Audio Stellar Power Plant 3
This document serves as the Owner's Reference Manual for the PS Audio Stellar Power Plant 3 AC Regenerator. It provides essential information for safe and optimal use of the device.
Introduction
Thank you for choosing the PS Audio Stellar Power Plant 3. This AC regenerator is designed to provide clean, regulated AC power to your audio and video equipment, enhancing their performance by removing noise and distortion from your home's power supply. The P3 effectively acts as a local power station for your connected devices.
For detailed information and support, PS Audio can be contacted at:
- PS Audio, Inc.
- 4865 Sterling Drive
- Boulder, CO 80301
- 1 (800) PSAUDIO
- service@psaudio.com
- www.psaudio.com
Safety Information
Important Safety Instructions: READ AND FOLLOW ALL INSTRUCTIONS. HEED ALL WARNINGS.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE APPARATUS. THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTH CONNECTION.
Clean only with a dry cloth. Do not place flammable material on top of or beneath the unit. The PS Audio® Stellar Power Plant 3 is passively cooled and requires adequate ventilation. Do not bypass the ground pin on the AC cord. Consult an electrician for outlet replacement if needed. Protect the power cord from damage. Unplug during lightning storms. Power off all components before making connections. Refer all servicing to qualified personnel.
Getting Started
The Stellar Power Plant 3 comes with a power cable and an owner's reference manual. Familiarize yourself with the front and rear panel controls and indicators.
- Front Panel: Features include the PS Audio Logo LED (Idle/On status), Output LED, MultiWave LED, CleanWave LED, and an Infrared Remote Sensor.
- Rear Panel: Includes the Master Power Switch, IEC AC Power Inlet, Fuse Socket, Regenerated/Bypass Switch for High Current outlets, Filtered High Current or Regenerated Outlets, and Regenerated Outlets.
Installation Considerations: Ensure proper ventilation, especially when stacking units. Use heavy-gauge shielded power cables for long distances. Avoid using other power conditioning equipment in conjunction with the P3 without careful evaluation.
Plugging In The Power Cable: Connect the provided or an aftermarket power cable to the IEC AC inlet on the rear panel and then to a wall socket.
Plugging In Your Equipment: Connect your audio/video components to the regenerated outlets on the rear panel. For equipment requiring higher current, use the Filtered High Current outlets by flipping the bypass switch on the rear panel to the up position. Ensure the unit is powered off before switching between settings.
Powering On Your P3: Flip the master power switch on the rear panel to the 'on' position. The unit will initialize, indicated by the PS Audio Logo LED flashing, and then glow solid blue when ready.
Operation Guide
The master power switch should remain on. The P3 can be placed in idle mode when not in use by pressing the PS Audio logo button on the front panel or the power button on the remote. The logo button will not be lit when in idle mode.
Output Indicator: The Output LED indicates the power draw: green (up to ~90%), yellow (~90-100%), and red (over 300W, potentially entering fault mode).
MultiWave Function: Press the 'MW' button on the remote to toggle this feature. It increases the charge time of the output waveform to reduce power supply ripple. The MultiWave LED glows blue when active.
CleanWave Function: Press the 'Clean' button on the remote to activate this feature, which injects higher frequencies to degauss connected magnets. The CleanWave LED glows blue during the 5-second cycle.
Troubleshooting
Fault Mode: If the PS Audio LED Logo button flashes blue rapidly, the unit has detected an error. Check the status of other LEDs for specific error codes (e.g., Output LED flashing red/yellow for low voltage, red/green for high voltage).
Overload/Short Circuit: If the unit enters fault mode due to overload or short circuit, disconnect all connected equipment and reconnect one by one to identify the problematic device.
Amp Fault/DC Voltage/Corrupt Flash: If the MultiWave, Output, or CleanWave LEDs indicate specific faults, contact PS Audio Customer Support for assistance.
Specifications
Detailed specifications for the Stellar Power Plant 3 are provided, including dimensions, weight, electrical ratings, and performance metrics, varying by country (U.S./Japan vs. Europe/Asia).
Warranty Information
The limited warranty is valid for 3 years from the date of purchase. Registering the product is recommended. The warranty covers defects in material and workmanship. It does not cover damage from accidents, misuse, improper installation, unauthorized repairs, or acts of God. Shipping costs for returns are the responsibility of the owner, while return shipping of repaired/replaced units is covered by PS Audio.
Limitations on liability and consequential damages apply. Warranty transfer to a subsequent purchaser is possible by contacting PS Audio.
Service Information
For warranty service within North America, contact PS Audio customer support. Obtain a Return Merchandise Authorization Number (RMA#) before returning any item. Use original packaging for shipping and insure the product. PS Audio is not responsible for damage during transit. State laws may provide additional rights.
Your Product
This section is for recording your product's serial number and purchase information.
