Installation Guide for REZNOR models including: EUH, UDX, UDXC, UDZ, EUH Ceiling Suspention Kit, EUH, Ceiling Suspention Kit, Suspention Kit, Kit
Engineering and Specifications – Reznor HVAC
File Info : application/pdf, 4 Pages, 265.75KB
DocumentDocumentRevision: OPT-CK22 (02-25) 1037006-C Supersedes: OPT-CK22 (11-24) 1037006-B CEILING SUSPENSION KIT INSTALLATION FOR ELECTRIC AND GAS-FIRED UNIT HEATERS OPTION CK22 FOR ELECTRIC MODEL EHU, GAS-FIRED MODEL UDXC, AND OBSOLETE GAS-FIRED MODELS UDX AND UDZ DANGER Before suspending the heater, ensure that the installation location has sufficient clearances to combustibles and ensure that the supporting structure has sufficient load-carrying capacity to support the weight of the unit. Refer to the installation manual provided with the heater for location requirements, recommended clearances, and unit weights. GENERAL INFORMATION NOTE: The following assumes that the heater has not been installed. · The ceiling suspension kit (see Figure 1) allows the heater to be installed 1 inch from the ceiling without hanger rods. For gas-fired unit heaters, the kit is used only on unit sizes 30125. · Refer to the installation manual provided with the heater for important safety information. EUH UDX, UDXC, UDZ Figure 1. Ceiling Suspension Kit DO NOT DESTROY. PLEASE READ CAREFULLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. KIT COMPONENTS Ensure that all components listed in Table 1 are available before beginning installation. Component Ceiling bracket Screw, sheet metal Table 1. Kit Components Model EUH UDX, UDXC, UDZ Kit PN 1042759 1036357 Component PN (Quantity) 1042700 (2) 1034211 (2) 195638 (13) 195638 (10) INSTALLATION 1. Remove all sheet metal screws that secure front and rear of cabinet top. 2. Align ceiling brackets with screw holes in front and rear of cabinet top and secure brackets to heater using screws from kit. 3. While supporting heater bottom with plywood or other suitable material, lift heater into place using suitable lift or assistance and secure ceiling brackets to ceiling using field-supplied hardware. Specifications and illustrations subject to change without notice or incurring obligations. Latest version of this manual is available at www.reznorhvac.com. ©2025 Reznor LLC, O'Fallon, MO. All rights reserved. OPT-CK22 (02-25) 1037006-C Révision : OPT-CK22 (02-25) 1037006-C Remplace : OPT-CK22 (11-24) 1037006-B INSTALLATION DU KIT DE SUSPENSION AU PLAFOND POUR CHAUFFAGES ÉLECTRIQUES ET À GAZ OPTION CK22 POUR MODÈLE ÉLECTRIQUE EHU, MODÈLE À GAZ UDXC ET MODÈLES À GAZ OBSOLÈTES UDX ET UDZ DANGER Avant de suspendre le radiateur, assurez-vous que l'emplacement d'installation dispose d'un espace libre suffisant par rapport aux combustibles et que la structure de support a une capacité de charge suffisante pour supporter le poids de l'appareil. Reportez-vous au manuel d'installation fourni avec le radiateur pour connaître les exigences d'emplacement, les dégagements recommandés et les poids de l'unité. RENSEIGNEMENTS GÉNÉRAUX NOTE: Ce qui suit suppose que le radiateur n'a pas été installé. · Le kit de suspension au plafond (voir Figure 1) permet d'installer le radiateur à 1 pouce du plafond sans tiges de suspension. Pour les radiateurs à gaz, le kit est utilisé uniquement sur les unités de taille 30125. · Reportez-vous au manuel d'installation fourni avec le radiateur pour obtenir des informations de sécurité importantes. EUH UDX, UDXC, UDZ Figure 1. Kit de suspension au plafond NE PAS DÉTRUIRE. VEUILLEZ LIRE ATTENTIVEMENT/CONSERVER EN UN LIEU SÛR POUR RÉFÉRENCE FUTURE. COMPOSANTS DU KIT Assurez-vous que tous les composants répertoriés dans le Tableau 1 sont disponibles avant de commencer l'installation. Composant Support plafond Vis, tôle Tableau 1. Composants du kit Modèle EUH UDX, UDXC, UDZ Kit PN 1042759 1036357 Composant PN (quantité) 1042700 (2) 1034211 (2) 195638 (13) 195638 (10) INSTALLATION 1. Retirez toutes les vis à tôle qui fixent l'avant et l'arrière du dessus de l'armoire. 2. Alignez les supports de plafond avec les trous de vis à l'avant et à l'arrière du dessus de l'armoire et fixez les supports au radiateur à l'aide des vis du kit. 3. Tout en soutenant le bas du radiateur avec du contreplaqué ou un autre matériau approprié, soulevez le radiateur en place à l'aide d'un élévateur ou d'une assistance appropriée et fixez les supports de plafond au plafond à l'aide du matériel fourni sur le terrain. Spécifications et illustrations sujettes à changements sans préavis ou sans aucune obligation. La dernière version de ce manuel est disponible sur www.reznorhvac.com. ©2025 Reznor LLC, O'Fallon, MO. Tous droits réservés. OPT-CK22 (02-25) 1037006-C