Altronix Home
Installation Guide for Altronix models including: HubWayLDD Series Active UTP Transceiver Hubs with Integral Camera Power, HubWayLDD Series, Active UTP Transceiver Hubs with Integral Camera Power, Active UTP Transceiver Hubs, UTP Transceiver Hubs, Transceiver Hubs, Hubs
Altronix HUBWAYLD16D | UTP Active Transceiver Hub, 16 Channe
File Info : application/pdf, 8 Pages, 1.19MB
DocumentDocumentVideo · Data · Power HubWayLDD Series Active UTP Transceiver Hubs with Integral Camera Power Models Include: HubWayLD8D HubWayLD16D - UL Listed eight (8) Channel Active UTP - UL Listed sixteen (16) Channel Active UTP Transceiver Hub with Integral Camera Power Transceiver Hub with Integral Camera Power HubWayLD82D - UL Listed eight (8) Channel Active UTP Transceiver Hub with Integral Camera Power - Includes eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners HubWayLD162D - UL Listed sixteen (16) Channel Active UTP Transceiver Hub with Integral Camera Power - Includes sixteen (16) UL Listed Accessory HubWayAv Video Balun/Combiners HubWayLD83D - UL Listed eight (8) Channel Active UTP Transceiver Hub with Integral Camera Power - Includes eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners HubWayLD163D - UL Listed sixteen (16) Channel Active UTP Transceiver Hub with Integral Camera Power - Includes sixteen (16) UL Listed Accessory HubWayDv Video Balun/Combiners Installation Guide Z1409 Rev. 030408 More than just power.TM Installing Company: _______________ Service Rep. Name: __________________________________ Address: _____________________________________________ Phone #: __________________ Overview: Altronix HubWayLD8D/16D Active UTP Transceiver Hub with Integral Camera Power transmits UTP video, RS422/ RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 or 16 camera channels in a space saving 1U EIA 19" rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to 3000 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individually selectable 24VAC or 28VAC PTC protected outputs with surge suppression. An optional HubSat4D Passive UTP Transceiver Hub with Integral Camera Power can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher structured cable back to the HubWayLD8D/16D. In addition, the HubSat4D provides power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs. HubWayLD Specifications: HubWayLD8D/LD82D/LD83D Input: · 115VAC, 60Hz, 1.5A or 230VAC 50/60Hz, 1A. Video: · Eight (8) channels of video over twisted pair up to a distance of 3000 ft. per channel. · Eight (8) 75 ohm video outputs. Power: · Unit provides up to 1A max. per channel not to exceed a total of 5A (150VA) maximum current. HubWayLD16D/LD162D/LD163D Input: · 115VAC 60Hz, 3A or 230VAC 50/60Hz, 1.5A. Video: · Sixteen (16) channels of video over twisted pair up to a distance of 3000 ft. per channel. · Sixteen (16) 75 ohm video outputs. Power: · Unit provides up to 1A max. per channel not to exceed a total of 10A (300VA) maximum current. Common Specifications: Agency Listings: · UL Listed for Commercial CCTV Equipment (UL 2044). Data: · RS422/RS485 data inputs. Power: · Individually selectable 24VAC or 28VAC power outputs with OFF position. · PTC protected output are rated @ 1A per channel. · Surge suppression. Visual Indicators: · Individual video signal LED indicators. · Individual power LED indicators. Features: · Picture and Gain control. · Illuminated master power disconnect circuit breaker with manual reset. · IEC 320 - 3-wire grounded line cord (detachable). · Unit can be rack, wall or shelf mounted. · 1U rack mount chassis for standard EIA 19" rack. Accessories: · Video Balun/Combiners: - HubWayAv: for use with 24VAC cameras. - HubWayAv2: for use with 24VAC cameras. - HubWayDv: for use with 12VDC cameras. - HubWayDvi: for use with non-isolated 12VDC cameras. · Optional HubSat4D allows transmission of up to four (4) video signals over a single CAT-5 or higher structured cable. Additional Models: HubWayLD82D · HubWayLD8D with eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners for 24VAC Cameras. HubWayLD162D · HubWayLD16D with sixteen (16) UL Listed Accessory HubWayAv Video Balun/Combiners for 24VAC Cameras. HubWayLD83D · HubWayLD8D with eight (8) UL Listed Accessory HubWayDv Video Balun/Combiners for 12VDC Cameras. HubWayLD163D · HubWayLD16D with sixteen (16) UL Listed Accessory HubWayDv Video Balun/Combiners for 12VDC Cameras. WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes. - 2 - HubWayLD8D / HubWayLD16D Installation Instructions: 1. Set the input voltage selector switch located on the left side of the HubWayLD8D/LD16D unit (facing front panel) for 115VAC or 230VAC operation (Fig. 1k, pg. 4). 2. Attach mounting brackets to HubWayLD unit for rack or wall mount installation (Fig. 6-7, pg. 8). Affix rubber pads to HubWayLD for shelf installation (Fig. 8, pg. 8). 3. Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at least 3" from any video monitors). 4. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7). 5. Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWayLD8D/HubWayLD16D unit (Fig. 1j, pg. 4). Insert the plug end of the line cord into a grounded AC receptacle. 6. Set voltage output selector switch of each camera channel for 24VAC or 28VAC (Fig. 1d, pg. 4). 7. Connect the BNC video outputs for HubWayLD8D/LD16D Channels 1 - 8 (Channels 1-16) to the corresponding video inputs on the head end equipment (DVR) (Fig. 1f, pg. 4). 8. Connect the RS422/RS485 output of the head end equipment (DVR) to the one (1) or both data input terminal blocks of the HubWayLD8D or HubWayLD16D unit (polarity must be observed) (Fig. 1e, pg. 4). Note: The Data input terminals of the HubWayLD8D or HubWayLD16D must be wired in parallel for proper operation. When using fixed cameras disregard this step. 9. Connect Video Balun/Combiner at camera 1 to the HubWayLD8D or HubWayLD16D unit utilizing CAT-5 or higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1] of the HubWayLD8D/LD16D (Fig. 1a, pg. 4). Plug the RJ45 connector at the opposite end of the structured cable into the RJ45 jack of the Video Balun/Combiner located at camera 1. · For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Fig. 2a, 2b, 2e, pg. 5). · For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Fig. 2c, 2d, pg. 5). · For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Fig. 2c, 2d, pg. 5). Repeat steps 6-9 for each additional camera (Channels 2-8 or Channels 2-16). Note: When a particular camera exceeds the maximum distance for power transmission, a local external power source is required. Optionally, an Altronix HubSat4D Passive UTP Transceiver Hub with Integral Camera Power may be utilized (Fig. 4a, pg. 6). The combined total cable distance must not exceed 3,000 ft. for video transmission between the HubWayLD8D/LD16D and each camera routed through the HubSat4D. 10. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7) and measure the output voltage at the power output of each Video Balun/Combiner (Fig. 2b, 2d, pg. 5) before powering each camera to ensure proper operation and avoid possible damage. · HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Fig. 2a, 2b, 2e, pg. 5). · HubWayDv/HubWayDvi - Terminals marked [ 12VDC +] (Fig. 2c, 2d, pg. 5). 11. Set illuminated master power disconnect circuit breaker to the (OFF) position to make the final connections (Fig. 5, pg. 7). 12. Connect the power outputs of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to the power inputs of the cameras (Fig. 2a-2e, pg. 5). Polarity must be observed. 13. Connect the terminals marked [+ DATA ] of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/ Combiners to the data terminals of the cameras for PTZ control (Fig. 2a-2e, pg. 5). Polarity must be observed. When using fixed cameras disregard this step. 14. Connect the BNC connectors of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/ Combiners to the BNC video outputs of the cameras (Fig. 2a-2e, pg. 5). 15. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7). 16. The power LEDs (Red) located on the front of the HubWayLD8D/LD16D will illuminate when AC power is present (Fig. 1c, pg. 4). Note: If any of these LEDs are not illuminated either a voltage output selector switch is in the OFF position or the PTC is tripped for that channel. To reset the PTC: 1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain in the OFF position for approximately 2 minutes in order for the PTC to reset. 2. Eliminate the trouble condition (short circuit or overload). 3. Set the voltage output selector switch for 24VAC or 28VAC (Fig. 1d, pg. 4). 17. AC LEDs (Green) of the HubWayAv or DC LEDs (Red) of the HubWayDv/HubWayDvi Video Balun/ Combiners will illuminate indicating power is present at the cameras (Fig. 2b, 2d, pg. 5). 18. The video signal indicator LEDs (Red) located on the rear of the HubWayLD8D/LD16D will illuminate when video signal is present (Fig. 1i, pg. 4). If any of these LEDs are not illuminated, no video signal is present for that corresponding channel. 19. Optimize the picture quality for all camera channels by adjusting the corresponding potentiometers marked [Picture] (Fig. 1g, pg. 4). 20. Set gain for all camera channels adjusting the corresponding potentiometers marked [Gain] (Fig. 1h, pg. 4). HubWayLD8D / HubWayLD16D - 3 - - 4 - Fig. 1 1e - Data: 1b - Channels 1-4, Channels 5-8, Channels 9-12 & Channels 13-16: Removable terminal blocks for RS422/ CAT-5 or higher structured cable from optional HubSat4D enables video RS485 input from head end transmission from up to four (4) cameras. equipment (DVR) for 1a - Channels 1-8 (HubWayLD8) or Channels 1-16 (HubWayLD16): PTZ control. Top View Data input from Head End Equipment (DVR). + -- CAT-5 or higher structured cable to Video/Balun Combiners at cameras 1-8 or 1-16. When using an optional HubSat4D any of the outputs can be utilized for the data transmission to PTZ's. 1c - LED(s) 1-16: 1d - Output voltage switches: Power indicators. Selects 24VAC/28VAC/OFF for each output. Front RESET OFF Rear 1 2 3 4 CH 1-4 5 6 7 8 CH 5-8 + DATA 1-8 28VAC OFF 24VAC 9 10 11 12 CH 9-12 13 14 15 16 CH 13-16 + DATA 9-16 28VAC OFF 24VAC 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN 1f - BNC Connector: Video outputs to head end equipment (DVR). 1g - Picture: Adjusts video quality. 1h - Gain: Regulates the output video and sync levels. PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN AC POWER 1i - LED(s) 1-16: Video signal indicators. 1j - IEC 320 Connector: 115VAC 60Hz/230VAC, 50/60Hz (grounded line cord included). 1k - Input Voltage Switch: 115VAC 220VAC Selects 115VAC 60Hz/230VAC 50/60Hz (switch is located on the left side of the unit). HubWayLD8D / HubWayLD16D HubWayAv, HubWayAv2, HubWayDv, and HubWayDvi Video Balun/Combiners: Altronix Model Number Input Voltage from HubWay Unit Output Voltage to Camera HubWayAv *24VAC/28VAC *24VAC/28VAC HubWayAv2 *24VAC/28VAC *24VAC/28VAC HubWayDv *24VAC/28VAC 12VDC *Based on camera load and structured cable length. Camera Type *24VAC/28VAC *24VAC/28VAC 12VDC cameras Power LED Green N/A Red Fig. 2 Fig. 2a Fig. 2b VIDEO HubWayAv VIDEO BALUN/COMBINER CAT5 AC +DATA-- POWER RJ45 Jack Wire Connectors Fig. 2c Fig. 2d VIDEO HubWayDv VIDEO BALUN/COMBINER CAT5 +DATA-- -- 12VDC+ * Also Available as: HubWayDvi Video Balun/ Combiner for non-isolated 12VDC cameras RJ45 Jack Wire Connectors To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Fig. 2e - HubWayAV2 Cat5 back to HubWay or HubSat Green Power LED AC Power to Camera -- Data to + Camera To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Power to Camera Data to Camera Red Power LED + 12VDC Power -- to Camera -- Data to + Camera HubWayAv/HubWayAv2 passes AC voltage from pins 4, 5, 7, 8 to terminals marked [AC Power] (Fig. 3, pg. 5). Video from Camera HubWayDv/HubWayDvi converts AC voltage to DC voltage from pins 4, 5, 7, 8 to terminals marked [ 12VDC +] (Fig. 3, pg. 5). Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations 1 - White/Orange [VIDEO +] 2 - Orange [VIDEO ] 3 - White/Green [DATA +] 4 - Blue [AC 1] 5 - White/Blue [AC 2] 6 - Green [DATA ] 7 - White/Brown [AC 2] 8 - Brown [AC 1] HubWayLD8D / HubWayLD16D - 5 - Typical Applications: Fig. 4 Head End Equipment (DVR) RS485 Data Rear Video Monitor 8 7 6 5 4 3 2 1 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN AC POWER 1 2 3 4 CH 1-4 5 6 7 8 CH 5-8 + DATA 1-8 28VAC OFF 24VAC Video Power CAT-5 Video Power Video Data Power Four (4) Video signals on a single CAT-5 CAT-5 Front Data (CAT-5) CAT-5 Video Data Power Max. video 3000 ft. HubWayAv Fixed Camera Video Balun Combiner HubWayDv/Dvi Video Balun Fixed Combiner Camera HubWayDv/Dvi PTZ Video Balun Camera Combiner HubWayAv Video Balun Combiner PTZ Camera Video Data Power HubWayAv PTZ Camera Video Balun Combiner Outdoor PTZ Camera Outdoor NEMA Rated Power Supply Video Data HubWayAv or HubWayDv/Dvi Video Balun Combiner Video Power CAT-5 HubWayDv/Dvi Fixed Camera Video Balun Combiner 24VAC/28VAC Camera Power Provided by HubSat4D 115VAC Input, 50/60Hz Power Video (Coax) Fixed Camera Fig. 4a - Optional hookup utilizing HubSat4D. Power 115VAC Input, 50/60Hz - 6 - HubWayLD8D / HubWayLD16D The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product's enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside. Refer servicing to qualified service personnel. 1U EIA 19" Rack Mount Chassis Dimensions (H x W x D approximate): 1.625" x 19.125" x 8.5" (41.3mm x 486mm x 216mm) Rear 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN 1.625"(41.3mm) 17.625" (447.7mm) AC POWER 8.5" (216mm) Top and Bottom 0.75" (19.1mm) Front 1 2 3 4 CH 1-4 5 6 7 8 CH 5-8 28VAC OFF + DATA -1-8 24VAC 19.125" (486mm) 9 10 11 12 CH 9-12 13 14 15 16 CH 13-16 + DATA -9-16 28VAC OFF 24VAC (ON) Fig. 5 Illuminated master power disconnect circuit breaker: · OFF position Circuit breaker tripped Switch not illuminated. · RESET (ON) position Switch illuminated. HubWayLD8D / HubWayLD16D - 7 - Mounting Options: Rack Mount Installation 1. Remove factory installed screws from both sides of the rack chassis (Fig. 6a). 2. Install mounting brackets (A) on the left and right side of rack chassis using the two (2) flat head screws (B) (included) (Fig. 6b). 3. Place unit into desired EIA 19" rack position and secure with mounting screws (not included) (Fig. 6c). Fig. 6 Fig. 6a Fig. 6b Fig. 6c Top Front Left Top Top Front Left Remove B A Front Left Wall Mount Installation 1. Install mounting brackets (A) on the left and right side of rack chassis using two (2) flat head screws (B) (included) (Fig. 7a). 2. Place unit at desired location and secure with mounting screws (not included) (Fig. 7b). Caution: It is necessary to make sure mounting screws are securely fastened to a beam when installing. Fig. 7 Fig. 7a Fig. 7b B A Shelf Installation 1. Position and affix rubber pads (C) (included) at Mounting Hardware (Included): each corner on the bottom of the unit (Fig. 8). 2. Place unit in desired location. Fig. 8 A Two (2) mounting brackets Left Side B Six (6) flat head screws for mounting brackets. C Rubber Pad C Four (4) rubber pads. Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIHubWayLD8D/HubWayLD16D K22U MEMBER - 8 - HubWayLD8D / HubWayLD16D