autonics.com
Manual-Hub.com - Free English product PDF Documents!
Instruction Manual for Autonics models including: M4N-DV-XX Digital Panel Meter, M4N-DV-XX, Digital Panel Meter, Panel Meter, Meter
AUTONICS M4N-DV-XX (01) PDF MANUAL - MANUAL-HUB.COM
File Info : application/pdf, 1 Pages, 1.03MB
DocumentDocumentDRW170795AA DIGITAL PANEL METER M4N SERIES INSTRUCTION MANUAL Thank you for choosing our Autonics product. Please read the following safety considerations before use. Safety Considerations Please observe all safety considerations for safe and proper product operation to avoid hazards. Safety considerations are categorized as follows. Warning Failure to follow these instructions may result in serious injury or death. Caution Failure to follow these instructions may result in personal injury or product damage. The symbols used on the product and instruction manual represent the following symbol represents caution due to special circumstances in which hazards may occur. Warning 1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.) Failure to follow this instruction may result in fire, personal injury, or economic loss. 2. Install on a device panel to use. Failure to follow this instruction may result in fire. 3. Do not connect, repair, or inspect the unit while connected to a power source. Failure to follow this instruction may result in fire. 4. Check 'Connections' before wiring. Failure to follow this instruction may result in fire. 5. Do not disassemble or modify the unit. Failure to follow this instruction may result in fire. Caution 1. Use the unit within the rated specifications. Failure to follow this instruction may result in fire or product damage. 2. Use dry cloth to clean the unit, and do not use water or organic solvent. Failure to follow this instruction may result in fire. 3. Do not use the unit in the place where flammable/explosive/corrosive gas, humidity, direct sunlight, radiant heat, vibration, impact, or salinity may be present. Failure to follow this instruction may result in fire or explosion. 4. Keep metal chip, dust, and wire residue from flowing into the unit. Failure to follow this instruction may result in fire or product damage. The above specifications are subject to change and some models may be discontinued without notice. Be sure to follow cautions written in the instruction manual and the technical descriptions (catalog, homepage). Ordering Information M4N DV 01 Measuring input range Power supply Measurement functions Measuring input Size Digit Item DC volt input F.S. DC ampere input F.S. 1 199.9mV 199.9 2 1.999V 1.999mA 3 19.99V 19.99mA 4 199.9V 199.9mA Blank Option Option 0 5VDC 1 12-24VDC V Voltage A Current I Scaling(DC4-20mA)2 D DC Type N DIN W48×H24mm 4 1999(3½ Digit) M Meter 1: M4N series is to measure DC only. AC voltage and AC current is not available to be measured. 2: 1-5VDC measuring input is optional. Specifications Model Measurement function Power supply Allowable voltage range Power consumption Display method Max.display range Display accuracy Sampling cycle A/D conversion method Response time Max.allowable input Sampling time Insulation resistance Dielectric strength Noise immunity Vibra -tion Mechanical Malfunction Mechanical Shock Malfunction Environ Ambient temperature -mnet Ambient humidity Unit weight M4N-DV- M4N-DA- M4N-DI- DC voltage DC current 5VDC, 12-24VDC DC4-20mA 90 to 110% of rated voltage 2W 7Segment LED Display(Character height: 10mm) Max. 1999 F.S.±0.2% rdg ±1digit 300ms Dual intergal method Approx. 2sec(0 to 1999) 150% of measurement input range 2.5 times/sec Over 100M(at 500VDC megger) 2000VAC 50/60Hz for 1 minute ±100V the square wave noise(pulse width: 1) by the noise simulator 0.75mm amplitude at frequency of 10 to 55Hz in each X, Y, Z direction for 1 hour 0.5mm amplitude at frquency of 10 to 55Hz in each X, Y, Z direction for 10 minutes 300m/s²(approx. 30G) in each X, Y, Z direction for 3 times 100m/s²(approx. 10G) in each X, Y, Z direction for 3 times -10 to 50, storage: -20 to 60 35 to 85%RH, storage: 35 to 85%RH Approx. 44g Environment resistance is rated at no freezing or condensation. Connections SOURCE1 [Position of the decimal point] INPUT 1 2 3 4 5 6 7 8 10³ 10² 10¹ COM LO 10 Hold Dot HI 1: 5VDC, 12-24VDC When changing the position of the decimal point, disconnect switching pattern point on PCB and change the decimal point in external terminal socket. When "1" or "-1" is flashes with a certain measurement input, disconnect power supply and then check the cables. 24 36 Dimensions 48 4 63 37 22 10 21 Panel cut-out Min. 60 (unit: mm) Min. 37 21.5 +0.5 -0 45.5 +0.5 -0 48×24 Bracket 58 Mounting Panel 19 63 Connections of Applications Simultaneous connection of voltmeter and ammeter 1 Power of the load A Load HI LOW HI LOW Voltmeter Ammeter Max. 10.0mm Panel boad tickness should be less than 10.0mm. DC power DC power supply 1 supply 2 1: Compared to measurement input range, higher measuring voltage needs a multiplier and lower measuring voltage needs a shunt. When using voltmeter and ammeter simultaneously, connect the separated power supply each. (-) terminal of the power and (-) terminal of measurement input are shorted. Cautions during Use 1. Follow instructions in 'Cautions during Use'. Otherwise, it may cause unexpected accidents. 2. 5VAC, 12-24VDC power supply should be insulated and limited voltage/current or Class 2, SELV power supply device. 3. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power. 4. Keep away from high voltage lines or power lines to prevent inductive noise. In case installing power line and input signal line closely, use line filter or varistor at power line and shielded wire at input signal line. Do not use near the equipment which generates strong magnetic force or high frequency noise. Connection with the line filter Connection with the varistor 110/ 220VAC Install the line filter close to the panel meter HI Panel meter LOW 110/ 220VAC HI Panel meter LOW Earth ground 5. This unit may be used in the following environments. Indoors (in the environment condition rated in 'Specifications') Altitude max. 2,000m Pollution degree 2 Installation category II Major products Photoelectric Sensors Temperature Controllers Fiber Optic Sensors Temperature/Humidity Transducers Door Sensors SSRs/Power Controllers Door Side Sensors Counters Area Sensors Timers Proximity Sensors Panel Meters Pressure Sensors Tachometer/Pulse (Rate) Meters Rotary Encoders Display Units Connector/Sockets Sensor Controllers Switching Mode Power Supplies Control Switches/Lamps/Buzzers I/O Terminal Blocks & Cables Stepper Motors/Drivers/Motion Controllers Graphic/Logic Panels Field Network Devices Laser Marking System (Fiber, Co, Nd: YAG) Laser Welding/Cutting System http://www.autonics.com HEADQUARTERS: 18, Bansong-ro 513beon-gil, Haeundae-gu, Busan, South Korea, 48002 TEL: 82-51-519-3232 E-mail: sales@autonics.com DRW170795AA https://manual-hub.com/