Instruction Manual for sgreen models including: MFGManual_Table_Top_Sgreen_Washout_Booth_2022_1.pdf v 1669056572, 1669056572, 1669056572 Table Top Washout Booth, Table Top Washout Booth, Top Washout Booth, Washout Booth, Booth

Tabletop Booth Manual

Sgreen Equipment Manuals

Manual

Sgreen Tabletop Washout Booth | by ScreenPrinting.com

• Google Docs
• Google Drive
• Download [pdf]
• Download Optimized



File Info : application/pdf, 12 Pages, 778.11KB

Document Document

Assembly Instructions
TABLE TOP
WASHOUT BOOTH
1

Tools Required:

· Two 7/16" wrenches · One 5/32" Hex wrench
What's in the box

Tag

Item

Qty.

1

MFWD-TABLEWASBDY

1

2

MFPB-TABLEWASHFOOT

4

3

MFSA-TABLEWASHDW

1

4

MFLS-TABLEWASHGST

2

5

MFCO-EDGETRIM

7

6

MFPB-TABLEWASHSID

2

7

MFLS-TABLEWASHBAK

1

8

MFPB-TABLEWASHSPCR

1

1

Parts Required:
What's in the box
7 8
1

6
5 4 3 2
2

Tag

Item

Description

Qty.

1

MFPB-TABLEWASHSTOFF

Table top Washout booth Screen holding stand-off

2

2

MFCO-SGWASHCAULK

Clear Caulk, Acrylic, 5.5 oz. Tube

1

3

PRHD-BTN1/4NC1/2SS

1/4-20 x 1/2 Button Head Allen Bolt Stainless steel

33

4

PRHD-WA1/4NEOBONDSS

1/4" Neobond Stainless steel conical washer

25

5

PRHD-ACN1/4NCGR5ZC

1/4-20 Acorn Nut Nickel

33

6

PRHD-WA1/4USSGR5ZC

1/4" USS flat washer

33

4 3

6 5

2

1

3

Step 1
Install the side panels (1) to the main sink body (2). Fully tighten the hardware. Neobond washers inside of the sink and standard flat washers outside of the sink.. Note: Refer to page 2 for hardware detail.
1
2
4

Step 2
Slide the rear panel on the inside of the side panel flap and align the hole patterns to each other. You will need to place the spacer in between the rear panel and the rear of sink before attaching the hardware.
5

Step 3
Install Rear panel (1) to the side panels (2) to the main sink body. Fully tighten the hardware. Neobond washers inside of the sink and standard flat washers outside of the sink. Note: Refer to Page 2 for hardware detail.
1
2
6

Step 4
Install Legs (1) to the side panels to the main sink body (2). Fully tighten the hardware. Neobond washers inside of the sink and standard flat washers outside of the sink. Note: Refer to Page 2 for hardware detail.
2
1
7

Step 5
Install edge trim (1) to the side panels (2) and front lip of sink Body (3). Some trimming may be needed for this step.
1 2
3
8

Step 6
Install Gussets (1) to the side panels (2) and the rear panel (3). Fully tighten the hardware. No Neobond washers used in this step. Finally, use supplied caulk to seal all seams where water could leak. Allow to dry per caulking instructions. Note: Refer to Page 2 for hardware detail.
1 2
3
9

NOTES:
NOTE: Logos, graphic elements and or photo images contained in this document may not be reproduced without the written consent of Ryonet 10

12303 NE 56th ST | Vancouver. WA 98662 | 360-576-7188
11