AlfredCam Quick Start Guide

What's in the Box

Upon opening the box, you will find the following items:

• AlfredCam Camera
• Power Adapter
• Micro USB Cable
• Mounting Stand
• Alignment Sticker
• 3M Sticker
• Screws & Anchors
• Quick Start Guide

About Your AlfredCam

Key components of the AlfredCam include:

• Status LED: Indicates the camera's operational status (e.g., blinking green for setup, solid red for errors).
• Microphone: Captures audio for recordings.
• Micro SD Card Slot: Located on the camera body, for optional local storage (card not included).
• Reset Button: A small, recessed button, typically found near the SD card slot, used for troubleshooting and factory resets.

Setting Up Your Device Together

Follow these steps to get your AlfredCam connected:

1. Download the App: Obtain the AlfredCamera app from your device's App Store (iOS) or Google Play Store (Android).
2. Launch and Sign In: Open the AlfredCamera app. Log in with your existing account credentials or create a new account if you are a new user.
3. Power On the Camera: Connect the AlfredCam to a power source using the provided Micro USB cable and power adapter. The Status LED on the camera should begin blinking green, indicating it is ready for setup.
4. Add Camera: Within the AlfredCamera app, tap the "Add a Camera" button [plus symbol]. Follow the on-screen prompts to connect your AlfredCam to your home Wi-Fi network (2.4GHz).

Mounting the Camera

To securely mount your camera, follow these instructions:

1. Position Alignment Sticker: Place the alignment sticker on the desired mounting surface (e.g., wall, ceiling).
2. Drill Pilot Holes: Using an 8mm drill bit, create two pilot holes approximately 20mm deep, aligning with the marks on the sticker.
3. Install Anchors & Screws: Insert the provided wall anchors into the drilled holes, then screw in the mounting screws to secure the stand.
4. Attach Mounting Stand: Fasten the mounting stand to the wall using the screws.
5. Mount Camera: Attach the AlfredCam to the mounting stand by sliding it into its designated position.

Troubleshooting & Frequently Asked Questions

What do I do when my device is not working properly?

If your AlfredCam is not functioning as expected, please try the following troubleshooting steps:

1. Restart and Reset: Begin by restarting the camera. If the problem persists, perform a factory reset. Locate the reset button (usually next to the SD card slot) and use a paperclip to press and hold it for approximately 5-10 seconds. The Status LED should turn solid red, indicating the reset is complete.
2. Check Internet Connection: Verify that your Wi-Fi router is properly connected to the internet and functioning.
3. Wi-Fi Network Compatibility: Ensure your mobile device is connected to the same 2.4GHz Wi-Fi network that you intend to use for the AlfredCam. The camera is not compatible with 5GHz networks.
4. Signal Strength: Position the AlfredCam within a reasonable range of your Wi-Fi router to ensure a stable and reliable connection.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.