HINKLEY Lighting
Installation Guide for HINKLEY models including: 16019OZ-LL, 16022MZ-LL, 16016MZ-LL, 16019OZ-LL Large LED Low Voltage Landscape Pathway Light, 16019OZ-LL, Large LED Low Voltage Landscape Pathway Light, Low Voltage Landscape Pathway Light, Landscape Pathway Light, Pathway Light, Light
Hinkley Lighting Springfield Large Classic LED Path Light Oil Rubbed Bronze LED Bulb Included 16019OZ-LL – Lighttrends.com
Hinkley Lighting Hardy Island Small Classic LED Path Light Matte Bronze LED Bulb Included 16022MZ-LL – Lighttrends.com
Hinkley Lighting Hardy Island Mini Classic LED Path Light Matte Bronze LED Bulb Included 16016MZ-LL – Lighttrends.com
File Info : application/pdf, 1 Pages, 12.61MB
DocumentDocumentHINKLEY HARDY ISLAND FAMILY Lamp / Lens Repacement Installation Instruction Item No: 16016/16022 start here /16019 SAVE THESE INSTRUCTIO Note: This Luminaire is designed for use with Hinkley approved 12 volt landscape systems. Connection to other systems may cause premature failure or non-intended operation. Instrucciones de Instalacion empezar aquí Número del 16016/ 16022/ actculo: 16019 Lens Rubber washer Luminire Head screws Harp Bi-pin bulb LUMINAIRE MOUNTING: (for typical ground stake mounting) tierra) 1. To prevent electrical shock, disconnect transformer from electrical supply before installation or service. 2. Run wire from Luminaire through mounting hole in top of ground stake. 3. Attach Luminaire to ground stake by threading to the mounting hole in stake until it fits snuggly against the bottom of stem. 4. Place stake in desired position and insert into ground until the flange of stake is flush with ground. 5. Strip the two wire leads from the Luminaire and connect to the main supply wire using the provided silicone filled wirenut. Silicone filled nuts are intended for one-time use. Wire Nut Capacity -2 pcs 18 AWG 2 pcs 12 AWG INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS, IMPORTANT SAFETY INSTRUCTIONS. superior de la estaca de tierra. brida de estaca quede al ras con el suelo. 5. Pele los dos cables de la luminaria y conéctelos a el cable de suministro principal utilizando el relleno de silicona proporcionado.tuerca de alambre. Las tuercas rellenas de silicona están diseñadas para un solo uso. Capacidad de tuerca de cable: 2 piezas de 18 AWG + 2 piezas de 12 AWG 1. Lamp gets hot quickly! Contact only switch / plug when turning on. 2. Do not touch hot lens, guard or enclosure. 3. Keep lamp away from materials that may burn. 4. Do not operate the luminaire fitting with a missing or damaged shield. 5. Luminaires shall not be installed within 10 feet (3m) of pool, spa or fountain. Typical Ground Stake spa o fuente. Protected by routing in close proximity to the luminaire or fitting, or next to a El principal cable de baja tensión de la luminaria es: building structure such as a house or deck. The main secondary wire is intended for shallow burial less than 6 inches (15.2cm) - in order to connect to the main low voltage cable. Have the length cut off so that it is connected to a connector within 6 inches (15.2cm) from a building structure, a luminaire or fitting. 1. Protegido por la ruta cerca de la luminaria o el accesorio, o al lado de una estructura de edificio como una casa o una cubierta. 2. El cable secundario principal está diseñado para enterramiento superficial: menos de 6 pulgadas (15,2 cm) - Para conectarse al cable principal de baja tensión. 3. Corte la longitud para que se conecte a un conector dentro de 6 pulgadas (15,2 cm) de una estructura de edificio, una luminaria o un accesorio. Relamping instructions: 1. Remove top shade (not shown) by turning in counter clockwise direction. Instrucciones de relamping 1. Retire la pantalla superior (no se muestra) 2. Remove harp by unscrewing the 2 screws under harp 3. Remove dome lens. 4. Replace lamp 5. Reassemble lens, harp, and shade girándola en sentido antihorario. 2. Retire el arpa desenroscando los 2 tornillos debajo del arpa 3. Retire la lente del domo . 4. Reemplace la lámpara 5. Vuelva a montar la lente, el arpa y la pantalla. commencer ici Número del 16016/ artículo: 16022/ 16019 : 5. Dénudez les deux fils du luminaire et connectez-les à le fil d'alimentation principal à l'aide du manchon rempli de silicone fourni fil de fer. Les noix remplies de silicone sont destinées à un usage unique.Capacité du serre-fil -2 pièces 18 AWG + 2 pièces 12 AWG Le câble principal basse tension du luminaire doit être Instructions de relamping 1. Retirez le store supérieur (non illustré) en tournant dans le sens antihoraire. 2. Retirez la harpe en dévissant les 2 vis sous la harpe 3. Retirez la lentille du dôme. 4. Remplacez la lampe 5. Remontez la lentille, la harpe et l'ombre HINKLEY 33000 Pin Oak Parkway, Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkley.com Rev 5/23/24