Owner's Manual for SONY models including: DSC-S730, DSC-S730 Cyber-Shot Digital Still Camera, Cyber-Shot Digital Still Camera, Digital Still Camera, Still Camera, Camera
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS. PUBLISHED BY SONY. ... the Instruction Manual in pdf (Cyber-shot Handbook ) for printing. 3-281-198-11.
27 ago 2023 — [Power, general]. Power: LR6 (size AA) Alkaline batteries (2), 3 V. HR15/51:HR6 (size AA) Nickel-Metal. Hydride batteries (2) (not supplied), 2.4 V.
File Info : application/pdf, 13 Pages, 1.45MB
DocumentDocumentSERVICE MANUAL Ver. 1.0 2007.11 Revision History Internal memory ON BOARD DSC-S730 US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Tourist Model Link SPECIFICATIONS SERVICE NOTE DI SASSEM BLY BLOCK DIAGRAM REPAIR PARTS LIST The components identified by mark or dotted line with mark are critical for safety. Replace only with part number specified. Les composants identifiés par une marque sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. In case of the lens block assy, main board, or main frame assembly failure, contact your local Sony Service Headquarter for the measures. DIGITAL STILL CAMERA DSC-S730 9-852-239-11 Sony EMCS Co. 2007K0200-1 © 2007.11 Published by Kohda TEC SPECIFICATIONS [System] Image device: 7.20 mm (1/2.5 type) color CCD, Primary color filter Total pixel number of camera: Approx. 7 410 000 pixels Effective pixel number of camera: Approx. 7 201 000 pixels Lens: 3× zoom lens f = 5.8 17.4 mm (35 105 mm when converted to a 35 mm still camera) F2.8 (W) 4.8 (T) Exposure control: Automatic exposure, Scene Selection (7 modes) White balance: Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash File format (DCF compliant): Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: AVI (Motion JPEG) Recording media: Internal Memory (approx. 22 MB), "Memory Stick Duo" Flash: Flash range (ISO sensitivity (Recommended Exposure Index) set to Auto): approx. 0.5 to 3.5 m (1 feet 7 3/4 inches to 11 feet 5 7/8 inches) (W)/approx. 0.5 to 2.0 m (1 feet 7 3/4 inches to 6 feet 6 3/4 inches) (T) [Input and Output connectors] (USB) A/V OUT terminal: Video, Audio (Monaural), USB communication USB communication: Hi-Speed USB (USB 2.0 compliant) [LCD screen] LCD panel: 6.0 cm (2.4 type) TFT drive Total number of dots: 112 320 (480×234) dots [Power, general] Power: LR6 (size AA) Alkaline batteries (2), 3 V HR15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2) (not supplied), 2.4 V ZR6 (size AA) Oxy Nickel Primary Battery (2) (not supplied), 3 V AC-LS5K AC Adaptor (not supplied), 4.2 V Power consumption (during shooting): 1.2 W Operating temperature: 0 to 40 C (32 to 104 F) Storage temperature: 20 to +60 C (4 to +140 F) Dimensions: 91.4×61.0×29.1 mm (3 5/8×2 1/2× 1 3/16 inches) (W/H/D, excluding protrusions) Mass: Approx. 189 g (6.7 oz) (including two batteries and strap, etc.) Microphone: Monaural Buzzer Exif Print: Compatible PRINT Image Matching III: Compatible PictBridge: Compatible Design and specifications are subject to change without notice. DSC-S730 -- 2 -- CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. : LEAD FREE MARK Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. FLEXIBLE Circuit Board Repairing Keep the temperature of the soldering iron around 270 C during repairing. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Do not touch the soldering iron on the same conductor of the Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than Be careful not to apply force on the conductor when soldering or unsoldering. ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may DSC-S730 also be added to ordinary solder. -- 3 -- TABLE OF CONTENTS Section Title Page 1. SERVICE NOTE 1-1. Process After Fixing Flash Error ····································· 1-1 1-2. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-1 2. DISASSEMBLY 2-1. Disassembly ····································································· 2-1 3. BLOCK DIAGRAM 3-1. Overall Block Diagram ··················································· 3-1 4. REPAIR PARTS LIST 4-1. Exploded Views ······························································· 4-1 4-1-1. Overall Section ······························································ 4-1 4-1-2. Main Frame Block ························································· 4-2 4-2. Accessories ······································································ 4-3 DSC-S730 -- 4 -- 1. SERVICE NOTE 1-1. PROCESS AFTER FIXING FLASH ERROR Method for Initializing the Flash Error Initialize Initializes the setting to the default setting. Even if you execute this function, the images stored in the internal memory are retained. 1 Select [OK] with v on the control button, then press z. The message "Initialize all settings Ready?" appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting. To cancel initializing Select [Cancel] in step 1 or 2, then press z. Be sure not to power off the camera while initializing. 1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: When replacing the camera, erase the data in internal memory of the board before replacement. Method for Copying the Data in Internal Memory Copy Copies all images in the internal memory to a "Memory Stick Duo". 1 Insert a "Memory Stick Duo" having sufficient free capacity. 2 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be copied Ready?" appears. 3 Select [OK] with v, then press z. Copying starts. To cancel copying Select [Cancel] in step 2 or 3, then press z. Use batteries with enough power remaining. If you attempt to copy image files using batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly corrupting the data. You cannot select images to copy. The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the "Memory Stick Duo" after copying, then format the internal memory ([Format] in [Internal Memory Tool]). A new folder is created on the "Memory Stick Duo" and all the data will be copied to it. You cannot choose a specific folder and copy images to it. The (Print order) marks on the images are not copied. Method for Formatting the Internal Memory This item does not appear when a "Memory Stick Duo" is inserted in the camera. Format Formats the internal memory. Note that formatting permanently erases all data in the internal memory, including even protected images. 1 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be erased Ready?" appears. 2 Select [OK] with v, then press z. The format is complete. To cancel formatting Select [Cancel] in step 1 or 2, then press z. DSC-S730 1-1 The following flow chart shows the disassembly procedure. 2-1. DISASSEMBLY 2 2. DISASSEMBLY 5 3 1 4 1 Open the BT LID 2 SCREW M 1.7 X 2.7 3 SCREW TP 1.7 X 4 4 SCREW TP 1.7 X 3.5 5 CABINET (REAR) ASSY 3 4 2 1 1 SCREW TP 1.4 X 3.5 2 SCREW TP 1.4 X 4 3 LCD 4 LCD PLATE DSC-S730 (To 2-2 Page) 3 1 2 1 BT LID SHAFT 2 BT LID 3 BT LID SPRING 2 plate 3 Note : When CABINET(FRONT) ASSY is removed, the plate will bends if CABINET(FRONT) ASSY is inclined too much. Please remove CABINET (FRONT) ASSY as in parallel as possible. 2-1 1 1 SCREW TP 1.4 X 3 2 SCREW TP 1.4 X 2.5 3 CABINET (FRONT) ASSY 1 2 3 (From 2-1 Page) Caution Shorting jig (1k / 1W) Note : After discharged, a transparent seal is put again. Do not lose the transparent seal removed when discharged. 1 STRAP SHAFT 2 SCREW TP 1.4 X 3 3 RL BLOCK DSC-S730 1 3 2 3 2 1 SCREW TP 1.7 X 3.5 2 SCREW TP 1.7 X 6.5 3 ST BLOCK ASSY 2-2 4 1 1 SCREW TP 1.4 X 2.5 2 SCREW TP 1.7 X 3.5 3 MAIN MOUNT 4 SUPPORT (JACK) 4 3 1 JACK LID 2 SCREW TP 1.4 X 3 3 LENS BLOCK ASSY 4 LID 5 MAIN FRAME 1 2 5 3-1. OVERALL BLOCK DIAGRAM 3. BLOCK DIAGRAM MAIN BOARD STROBE & TOP BOARD +3.1V D DGND TOP +3.1VD DGND SHUT1 SHUT2 PW _LE D PW R_KE Y TOP POWER LED 1 2 GREEN AUO LCD 2.36 INCH PANEL LCD_BACKLIGHT 1 2 RED SHUT1 SHUT2 PW_LE D PWR_KE Y F LASH_VP STROBE _CHG S T RO B E _T rg F LASH_RDY FLASH CHARGER 2 P1,P2 1 Q5 41 2 S NC 3 CAPACITOR 100UF 300V SELF TIMER LED 1 2 GREEN F LASH F LASH_VP +5VM +3.1V D DGND F LASH_VP F LASH_RDY +5VM F LASH_C HG_L STROBE _TRG +3.1VD STROBE _C HG AF _LE D DGND STROBE _PW R F LASH F LASH_RDY F LASH_CHG_L STROBE _TRG STROBE _CHG AF _LE D STROBE _PWR FLASH TUBE 1 3 Q2 2 LCD DSP +5VM +3.1VD +5VM +3.1V D LC D_E N LC D_MC LK LC D_VD LC D_HD LC D_SC LK LC D_SDATA LC D[0..7] MLC D_ON BL LCD_E N LC D_MC LK LCD_VD LCD_HD LCD_SCLK LCD_SDATA LC D[0..7] MLC D_O N BL LC D_E N LC D_MC LK LC D_VD LC D_HD LC D_SC LK LC D_SDATA LC D[0..7] MLC D_ON BL DGND DGND LCD +2.5V D DGND +2.5VD DGND DDR RAMD[0..15] RAMA[0..14] RAMLDM RAMW E _N RAMC AS RAMRAS RAMC S_N RAMLDQS RAMUDQS RAMUDM RAMC LK_N RAMC LK RAMC LK_E N RAMRE F DDR RA MD[0..15] RA MA [0..14] RA MLDM RAMWE _N RA MC A S RA MRA S RA MC S _N RA MLDQ S RA MUDQ S RA MUDM RA MC LK _N RA MC LK RAMCLK_E N RAMRE F SHUT1 SHUT2 PW _LE D PW R_KE Y RAMD[0..15] RAMA[0..14] RAMLDM RAMW E _N RAMC AS RAMRAS RAMC S_N RAMLDQS RAMUDQS RAMUDM RAMC LK_N RAMC LK RAMC LK_E N RAMRE F MODE DIAL F LASH_RDY F LASH_C HG_L STROBE _TRG STROBE _C HG AF _LE D STROBE _PW R FUNCTION KEY MS LED 1 2 GREEN +3.1V D DGND SW STA_LE D +3.1VD DGND SW _KE Y_ADC 1 SW _KE Y_ADC SW STA_LE D SW_KE Y_ADC1 SW_KE Y_ADC 12MHZ 21 STA_LE D SW _KE Y_ADC 1 SW _KE Y_ADC VP -7.5V +2.5V D +3.3V +3.1V D +5VM +13.4V +1.8V D VP -7.5V POWE R C C D_ON1 PW R_C TRL +2.5VD +3.3V +3.1VD +5VM +13.4V C C D_ON +1.8VD DGND C C D_O N1 PWR_CTRL VP +1.8V D +3.1V D +3.3V S C C D_O N DGND +3.3V +2.5V D DGND C C D_ON1 PW R_C TRL VP +1.8VD +3.1VD +3.3VS +3.3V +2.5VD DGND POWE R DSP BATT+2 C187 BATT-2 C159 1000PK_25V_X7R 1000PK_25V_X7R 21 21 2 12 1 0.1UK_16V_X5R 0.1UK_16V_X5R Q29 AO3415 3 1 2 Q42 AO3415 3 1 C186 2 C160 1 R131 100K 2 1 F5 1A/24V 2 1 -7.5V 2 1 F3 1.6A/32V R163 100K -7.5V FLASH_VP VP MIC MIC _N PXC LK HD VD C DS_E N SC LK SDATA AF E RST TG_E N VSUB_C on1 VSUB_C on2 C C D_ON TG_ON C DS_ON C C D[0..11] MS_ON R/B MS_INS# C LE WE WP ALE CE0 RE MS_C LK MD[0..7] F A23 F A20 F A22 F A21 BEEPER LE NS_PS SHUTTE R_M1 SHUTTE R_M0 IN1 IN2 IN3 IN4 LE NS_E N LE NS_SC LK LE NS_SDATA ZOOM_PI ZOOM_PR F OC US_PI PW R_ON PW RKE Y BAT_LOAD D+ DUSB_DE T AV_DE T VIDE O_OUT LINE _OUT BEEPER SW _PLAYBAC K SW _W IDE SW _TE LE PXCLK HD VD CDS_E N SCLK SDATA AFE RST TG_E N VSUB_Con1 VSUB_Con2 C C D_O N T G _O N C DS _O N C C D[0..11] CDS PXC LK HD VD C DS_E N SC LK SDATA AF E RST TG_E N VSUB_C on1 VSUB_C on2 C C D_ON TG_ON C DS_ON C C D[0..11] +3.3V -7.5V +13.4V DGND CDS DGND +3.1V D MS _O N R /B MS _INS # CLE WE WP ALE CE0 RE MS _C LK MD [0 ..7 ] F A23 F A20 F A22 F A21 ME MORY DGND +3.1VD MS_ON R/B MS_INS# C LE WE WP ALE CE0 RE MS_C LK MD[0..7] F A23 F A20 F A22 F A21 BEEPER ME MORY LE NS +3.1V D LE NS_PS SHUTTE R_M1 SHUTTE R_M0 IN 1 IN 2 IN 3 IN 4 LE NS_E N LE NS_SCLK LE NS_SDATA Z O O M_P I Z O O M_P R F OCUS_PI +5VM DGND P W R_O N PWRKE Y B A T _LO A D D+ DUSB_DE T AV_DE T V IDE O _O UT LINE _O UT BEEPER +3.1VD LE NS_PS SHUTTE R_M1 SHUTTE R_M0 IN1 IN2 IN3 IN4 LE NS_E N LE NS_SC LK LE NS_SDATA ZOOM_PI ZOOM_PR F OC US_PI +5VM DGND LE NS JA C K D+ DUSB_DE T A/V_DE T VIDE O_OUT LINE _OUT BEEPER +3.1VD DGND UGND 2 SW_PLAYBACK S W _W IDE SW_TE LE 1 JA C K 4 3 3 61 5 2 5 1 2 5 +3.3V -7.5V +13.4V DGND 2 1 33.75MHZ MEMORY STICK +13.4V BUZZER +3.1V D DGND UGND PC 4 6 3 6 4 2 1 32.768K Hz 3 4 +3.1V D Power 4 1 Out GND_3 3 2 GND_2 MIC 1 S P M0204HD5 MC4_4.72X3.76_173 G2412-0039-00 LENS BLOCK IRIS(METER) LENS ZOOM SENSOR ZOOM MOTOR FOCUS SENSOR FOCUS MOTOR IRIS MOTOR SHUTTER MOTOR 2 DSC-S730 3-1 4-1. EXPLODED VIEWS 4-1-1. OVERALL SECTION ns: not supplied 4. REPAIR PARTS LIST 3 15 4 6 13 16 11 12 1 18 2 10 7 19 5 (Note) 17 ns 14 15 9 Main Frame Block (See Page 4-2) 8 Note : The adjustment is not required after replacing the LCD · Refer to cover for mark . Ref. No. Part No. Description 1 X-2188-411-1 CABINET (FRONT) ASSY 2 X-2188-412-1 CABINET (REAR) ASSY 3 3-286-696-01 SHAFT, STRAP 4 3-286-697-01 BLOCK, RL 5 3-286-698-01 LCD 6 A-1444-049-A ST BLOCK ASSY 7 3-286-700-01 SHAFT, BT LID 8 3-286-701-01 LID, BT 9 3-286-702-01 SPRING, BT LID 10 3-286-703-01 LID, JACK Ref. No. 11 12 13 14 15 Part No. Description 3-287-023-11 SCREW M1.7 X 2.7 3-287-026-01 SCREW TP1.4 X 2.5 3-287-028-01 SCREW TP1.7 X 3.5 3-287-027-01 SCREW TP1.7 X 4 3-287-025-01 SCREW TP1.4 X 3 16 3-287-032-01 SCREW TP1.7 X 6.5 17 3-296-920-01 SCREW TP1.4 X 3.5 18 3-296-921-01 SCREW TP1.4 X 4 19 3-299-366-01 SCREW TP1.7 X 3.5 DSC-S730 4-1 4. REPAIR PARTS LIST 4-1-2. MAIN FRAME BLOCK ns: not supplied ns ns (Note 1) ns (Note 1) 104 104 102 102 103 101 105 (Note 2) Note 1 : In case of the lens block assy or main board failure, contact your local Sony service Headquarter for the measures. Note 2 : When separate lens block assy and main board for main frame replacement, assemble original lens block assy and main board back after repaire. Ref. No. 101 102 103 104 105 Part No. Description 3-286-699-01 3-287-024-01 3-287-026-01 3-287-028-01 3-286-704-01 SUPPORT (JACK) SCREW TP1.4 X 3 SCREW TP1.4 X 2.5 SCREW TP1.7 X 3.5 FRAME, MAIN DSC-S730 4-2 4-2. ACCESSORIES Checking supplied accessories. 4. REPAIR PARTS LIST Note 1: This item is supplied with the unit as an accessory, but is not prepared as a service part. A/V cable 3-196-980-01 USB cable 3-196-981-01 Wrist strap 2-050-981-01 Instruction Manual 3-281-198-11 3-281-198-21 3-281-198-31 3-281-198-41 3-281-198-51 3-281-198-61 3-281-198-71 3-281-198-81 3-281-198-91 3-281-199-11 3-281-199-21 3-281-199-31 3-281-199-41 3-281-199-51 3-281-199-61 3-281-199-71 (ENGLISH) (CND, AEP, UK, E, AUS, HK, JE) (FRENCH, ITALIAN) (CND, AEP) (SPANISH, PORTUGUESE) (AEP, E, JE) (GERMAN, DUTCH) (AEP) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, JE) (RUSSIAN, UKRAINIAN) (AEP) (ARABIC, PERSIAN) (E) (KOREAN) (KR, JE) (POLISH, CZECH) (AEP) (HUNGARIAN, SLOVAK) (AEP) (SWEDISH, FINNISH) (AEP) (NORWEGIAN, DANISH)(AEP) (THAI, MALAYSIAN) (E) (TURKISH, GREEK) (AEP) (ENGLISH, SPANISH) (US) (SIMPLIFIED CHINESE) (CH) LR6 (size AA) Alkaline Battery (Note 1) CD-ROM (Cyber-shot application software/ "Cyber-shot Handbook"/ "Cyber-shot Step-up Guide") *3-281-189-01 Cyber-shot Handbook(PDF) The CD-ROM supplied contains all of language version of the Instruction Manual in pdf (Cyber-shot Handbook.pdf) for printing. The printed matter is not supplied. If required, please order it with the part number below. * 3-281-190-11 (ENGLISH) * 3-281-190-21 (FRENCH) * 3-281-190-31 (ITALIAN) * 3-281-190-41 (SPANISH) * 3-281-190-51 (PORTUGUESE) * 3-281-190-61 (GERMAN) * 3-281-190-71 (DUTCH) * 3-281-190-81 (TRADITIONAL CHINESE) * 3-281-190-91 (SIMPLIFIED CHINESE) * 3-281-191-11 (RUSSIAN) * 3-281-191-21 (ARABIC) * 3-281-191-31 (PERSIAN) * 3-281-191-41 (KOREAN) * 3-281-191-51 * 3-281-191-61 * 3-281-191-71 * 3-281-191-81 * 3-281-191-91 * 3-281-192-11 * 3-281-192-21 * 3-281-192-31 * 3-281-192-41 * 3-281-192-51 * 3-281-192-61 * 3-281-192-71 * 3-281-192-81 (POLISH) (CZECH) (HUNGARIAN) (SLOVAK) (SWEDISH) (FINNISH) (NORWEGIAN) (DANISH) (THAI) (MALAYSIAN) (TURKISH) (GREEK) (UKRAINIAN) NOTE: Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Abbreviation AUS : Australian model CH : Chinese model CND : Canadian model HK : Hong Kong model JE : Tourist model KR : Korea model DSC-S730 4-3 Regarding Fuse MAIN BOARD F5 F3 DSC-S730 MANUFACTURER: KAMAYA ELECTRIC CO.,LTD. F5 TYPE: FCC10102AD RATING: 1.0A F3 MANUFACTURER: KAMAYA ELECTRIC CO.,LTD. TYPE: FCC16162AD RATING: 1.6A Reverse Revision History Ver. Date History 1.0 2007.11 Official Release Contents -- 985223911.pdf S.M. Rev. issued -- DSC-S730Acrobat Distiller 4.0.5 for Macintosh