TAC Truck Accessories Company | TACUSA
Installation Guide for TAC models including: 133800 Steelcraft Running Board Instructions, 133800, Steelcraft Running Board Instructions, Running Board Instructions, Board Instructions, Instructions
File Info : application/pdf, 4 Pages, 655.44KB
DocumentDocumentINSTALLATION INSTRUCTIONS VIEWPOINT ALUMINUM RUNNING BOARD 2010-2024 Toyota 4Runner Limited 2019-2022 4Runner Nightshade Edition 2010-2013 SR5 2022-2024 TRD Sport Models PART# 133800 www.tacautoparts.com VIEWPOINT ALUMINUM RUNNING BOARD 2010-2013 TOYOTA 4RUNNER SR5/2010-2024 4RUNNER LIMITED MODELS/2019-2022 4RUNNER NIGHTSHADE EDITION PARTS LIST: 1 Driver/Left Running Board 1 Passenger/Right Running Board 2 Front Mounting Brackets 4 Center & Rear Mounting Brackets 12 8-1.25mm x 30mm Hex Bolts 12 8mm Lock Washers 12 8mm x 22mm OD x 2mm Flat Washers 12 6mm x 20mm "T" bolts 12 6mm Lock Washers 12 6mm x 22mm OD x 2mm Flat Washers 12 6mm Hex Nuts (4) Center & Rear Mounting Brackets (2) Front Mounting Brackets Passenger/Right Side Running Board Front Longer angle to front Rear Driver/Left Side Running Board PROCEDURE: 1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. PLEASE NOTE: 200LBS IS THE MAXIMUM RATED LOAD FOR THE VIEWPOINT RUNNING BOARDS. 2. Starting on the passenger side of the vehicle, remove the existing (2) factory bolts located by the front tire opening securing the factory rocker panel bracket to the vehicle, (Figure 1). Select (1) Front Mounting Bracket. Hold the Front Bracket over the rocker panel bracket and line up the (2) mounting holes. Secure the brackets to the vehicle using the included longer (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 2). Do not tighten hardware at this time. 3. The center and rear brackets are identical. Select (1) Center/Rear Bracket and repeat the procedure as described in Step 2 to install it in the center mounting location, (Figure 3). NOTE: Install (1) mounting bracket at a time. Do not tighten hardware at this time. 4. Repeat Step 3 for rear Mounting Bracket installation. 5. Carefully unwrap the Running Board and select passenger side Board. Select (6) 6mm T-Bolts. Insert (3) T-Bolts into each channel on the bottom of the Running Board, (Figure 4). Slide the T-Bolts forward or back to line up with the (3) previously installed Mounting Brackets, (Figure 5). Hold the Running Board up to the vehicle at a slight angle and gently push it into position against the rocker panel, (Figure 6). Line up the T-Bolts with the slots in the Brackets. 6. Attach the Running Board to the Mounting Brackets with the included (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figures 7 & 8). Do not tighten at this time. 7. Level and adjust the Sidebar as desired and tighten all hardware. Repeat Steps 2 6 for the driver side Running Board installation. 8. Do periodic inspections to the installation to make sure that all hardware is secure and tight. www.tacautoparts.com Page 1 of 3 9/17/12 Rev1(DP) VIEWPOINT ALUMINUM RUNNING BOARD 2010-2013 TOYOTA 4RUNNER SR5/2010-2024 4RUNNER LIMITED MODELS/2019-2022 4RUNNER NIGHTSHADE EDITION To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Running Board. For gloss black finishes: Mild soap may be used to clean the Running Board Brackets. Passenger Side Installation Pictured Front Remove factory hex bolts Install the Mounting Brackets one at a time over the factory rocker panel brackets Front (Fig 1) Passenger side front mount pictured (2) 8mm x 30mm Hex Bolts (2) 8mm Flat Washers (2) 8mm Lock Washers Rear Fig 2 (Fig 3) Passenger side rear bracket location pictured (Fig 4) Insert T-Bolts into channels on bottom of Running Board www.tacautoparts.com Page 2 of 3 9/17/12 Rev1(DP) VIEWPOINT ALUMINUM RUNNING BOARD 2010-2013 TOYOTA 4RUNNER SR5/2010-2024 4RUNNER LIMITED MODELS/2019-2022 4RUNNER NIGHTSHADE EDITION Slide T-Bolt in slot to line up with Mounting Brackets Passenger Side Installation Pictured (Fig 5) Bottom of Running Board pictured Front (2) 6mm Flat Washers (2) 6mm Lock Washers (2) 6mm Hex Nuts Fig 6 Tilt the Running Board up and gently push back into position against rocker panel. Line up T-Bolts with Brackets (Fig 7) Front Bracket installation pictured Front (Fig 8) Center Bracket installation pictured Complete Installation www.tacautoparts.com Page 3 of 3 9/17/12 Rev1(DP)