Industrial Automation | HoneywellSensing Solution | Honeywell
Instruction Manual for Honeywell models including: SNG-S SERIES, Hall-Effect Speed Sensor, Speed Sensor, Hall-Effect Sensor, Sensor
SNG-S Series Hall-Effect Speed Sensor | Honeywell
SNG-S 시리즈 홀 이펙트 속도 센서 | Honeywell
File Info : application/pdf, 5 Pages, 642.91KB
DocumentDocumentINSTALLATION INSTRUCTIONS FOR THE SNG-S SERIES SPEED SENSORS 32347440 Issue D GENERAL SPECIFICATIONS Honeywell's SNG-S Series Speed Sensors use a magnetically biased Hall-effect integrated circuit (IC) to accurately sense movement of ferrous metal targets. The specially designed IC and a permanent magnet are sealed in rugged, probetype packages. The IC detects the alteration of the magnet's flux density when it is approached by ferrous metal. A sensor positioned at the circumference of a revolving gear wheel detects the teeth and spaces, and supplies a digital pulse output with frequency proportional to gear wheel speed. Optimum performance is dependent upon a combination of variables such as target material, geometry and speed, sensor/ target gap, and environmental temperature. TABLE 1. ELECTRICAL SPECIFICATIONS CHARACTERISTIC CONDITION/COMMENT SNG-SPRF-002 Supply voltage Supply current Reverse voltage protection Over voltage protection Short circuit protection Load dump regulated supply and 12 V battery ISO 16750-2 -- -- ISO 16750-2 -- ISO 16750-2 -- ISO 16750-2 ISO 16750-2:2012 11 01 (US* = 40 V, UA 13.5 ±0.5 V) Insulation resistance ISO 16750-2:2012 4.5 V to 24 V -- 20 mA max. -24 V -- 26.5 V -- 16 V -- 5b -- >10 MOhm at 500 Vdc -- PARAMETER SNG-SPRD-002 SNG-SPSC-001 SNG-SPRC-001 SNG-SPRD-003 SNG-SPRC-002 -- 8 V to 16 V -- 4.8 V to 16 V 15 mA -- -14 Vdc -- 26 V -- 16 V -- -- -- -- TABLE 2. MECHANICAL SPECIFICATIONS CHARACTERISTIC Carrier material Bushing material O-ring material Housing material Connector: integral mating Mounting torque O-ring lubrication SNG-SPRF-002 PBT thermoplastic SS304 70 durometer fluorocarbon, PTFE coating 17,0 mm ID x 2,0 mm CS PBT Bosch 928000453 Bosch 1928403966 8 ±0,5 N m with M6 screw PARAMETER SNG-SPRD-002 SNG-SPSC-001 SNG-SPRC-001 SNG-SPRD-003 SNG-SPRC-002 PBT SSTL fluorocarbon, brown 17,0 mm ID x 2,0 mm CS PBT mineral oil-based grease Amp Superseal 1.5 282087 20 ±3 N m with M8 screw SNG-SPRD-004 SNG-SPRC-003 -- 4.8 V to 24 V SNG-SPRD-004 SNG-SPRC-003 SNG-S SERIES SPEED SENSORS Issue D 32347440 TABLE 3. ENVIRONMENTAL SPECIFICATIONS CHARACTERISTIC Radiated immunity Bulk current injection ESD Conductive transients Conducted emissions Radiated emissions Thermal cycle Humidity Saline dunk Salt fog CONDITION/COMMENT SNG-SPRF-002 PARAMETER ALL OTHER CATALOG LISTINGS ISO 11452-2: 2004 ISO 11452-2: 2004 IEC 61000-4-3: 2008 ISO 11452-2, 400 MHz to 2.5 GHz 10 kHz to MHz, 60 m/V 200 MHz to 2.7 GHz, 100 V/m 800 kHz MHz to 1000 MHz, 3 m/V -- -- -- -- 100 V/m ISO 11452-4, 1 MHz to 400 MHz 100 mA SAE J1113/13 ISO 10605 ISO 7637-2, for 12 V system ISO 7637-2, for 12 V system ±4 kV contact, ±8 kV air -- TEST PULSE 1, 2a, 2b, 3a, 3b -- -- ±8 kV contact, ±15 kV air -- PULSE 1, 2a, 3a, 3b, 5a CISPR 25. 150 kHz to 108 MHz -- Class 3 CISPR 25. 150 kHz to 12.5 GHz -- Class 3 -40°C to 140°C -- 100 cycles -- 95 %RH at 55°C 10 %RH to 90 %RH at -40°C to 85°C, 150 cycles, 600 hr total -- -- 144 hr, EN/IEC 60068-2-30 0°C to 110°C -- 10 cycles, ISO 16750-4 5% salt solution by mass at 35°C and 93% RH 5% salt solution by mass at 35°C and for 400 hr, tested to 2000 hr with no ingress in 93% RH for 2000 hr -- the sensor packaging area Combined temperature and vibration test Vibration Degree of protection Resistance to fluids Operating temperature Storage temperature S 5% salt solution by mass at 35°C sinusoidal: 25 hr/axis, 3 perpendicular axes 30 g at 60 Hz to 1000 Hz and 15 g at 1000 Hz to 2000 Hz random: 25 hr/axis, 3 perpendicular axes 30 g at 25 rms Hz to 2000 Hz, -40°C to 125°C 3 perpendicular axes, 48 hr per axis IEC 50629 IEC 60529 -- -- -- -- 96 hours sinusoidal: 25 hr/axis, 3 perpendicular axes 15 g at 5 Hz to 2000 Hz -- random: 25 hr/axis, 3 perpendicular axes at 25 grms at 10 Hz to 2000 Hz -- IPX6, IPX9K, IPX7 -- -- -40°C to 150°C -55°C to 70°C -- 29.8 GRMS, 24 Hz to 2000 Hz, MIL-STD-202-214 -- IP69K, IP67 general under-the-hood automotive fluids -40°C to 140°C -40°C to 140°C SNG-S Series Speed Sensors Installation Instructions | sps.honeywell.com/ast | 2 SNG-S SERIES SPEED SENSORS Issue D 32347440 FIGURE 2. SCHEMATIC DIAGRAMS AND OUTPUT SPECIFICATIONS SNG-SPRF-002 VP SNG-SPRD-002 SNG-SPSC-001 SNG-SPRC-001 VCC = 8 V to 16 V VP Sensor element RP Open collector output Sensor element RP R2 = 1 kOhm R1 = 15 kOhm Ground CHARACTERISTIC CONDITION/COMMENT PARAMETER Signal type Power on Signal polarity Output signal: high low open collector -- not dependent on target rotation -- -- square wave default high and start from initial edge output low on teeth >VP - 0.5 V <0.6 V Load current output leakage current -10 µA 10 mA max. Frequency -- 0 kHz to 10 kHz CHARACTERISTIC Signal type Output signal: high low CONDITION/COMMENT open collector dependent on target geometry and sensor-totarget orientation Load current -- Frequency -- PARAMETER square wave (VP x (16.5)/(16.5 + RP in kOhm) 0.3 V to 2.2 V <(((VP-0.4) x 1 k)/(1 k + Rp in kOhm))+0.4 15 mA 0 kHz to 10 kHz SNG-SPRD-003 SNG-SPRC-002 VCC Sensor element Vp Rp Output SNG-SPRD-004 SNG-SPRC-003 VCC Vp Sensor element Rp Output 15 kOhm 1.47 nF CHARACTERISTIC CONDITION/COMMENT Signal type Output signal: high low Load current Frequency open collector dependent on the controller interface -- -- PARAMETER square wave >VCC - 0.5 V <0.5 V 20 mA 0 kHz to 10 kHz CHARACTERISTIC Signal type Output signal: high low Load current Frequency CONDITION/COMMENT open collector PARAMETER square wave dependent on the controller interface (Vp x (16.5)/(16.5+ Rp in kOhm)0.5 V <0.5 V -- 20 mA -- 0 kHz to 10 kHz SNG-S Series Speed Sensors Installation Instructions | sps.honeywell.com/ast | 3 SNG-S SERIES SPEED SENSORS Issue D 32347440 FIGURE 3. MOUNTING DIMENSIONS (FOR REFERENCE ONLY: MM/[IN].) 24 mm, right angle: SNG-SPRF-002 ø24,4 19,0 ø16,4 46 mm, straight: SNG-SPSC-001 22,95 Pin 3: Vcc Pin 2: Output Pin 1: Ground 41,0 44,0 ø6,70 Pin 3: Vcc Pin 2: Output Pin 1: Ground 19,0 ø16,4 ø24,4 25,9 ø8,70 18,5 4,5 11,5 ø20,30 25,2 5,00 24,0 ø14,91 ø17,86 0.5 mm to 2.0 mm Air gap 4,70 Clockwise rotation 9,50 5,00 30,4 33,7 46,00 0.5 mm to 2.0 mm Air gap Clockwise rotation 46 mm, right angle: SNG-SPRC-001 SNG-SPRC-002 SNG-SPRC-003 25,80 Pin 3: Vcc Pin 2: Output Pin 1: Ground ø24,4 23,4 19,00 ø13,90 ø17,86 67 mm, right angle: SNG-SPRD-002 19,00 ø16,4 SNG-SPRD-003 SNG-SPRD-004 ø26,10 ø8,70 Pin 3: Vcc Pin 2: Output Pin 1: Ground ø24,4 23,4 ø16,4 ø8,70 4,7 33,7 24,6 5,00 46,00 ø13,90 ø17,86 4,7 54,7 24,8 5,00 67,00 0.5 mm to 2.0 mm Air gap Clockwise rotation ø13,90 ø17,86 0.5 mm to 2.0 mm Air gap Clockwise rotation SNG-S Series Speed Sensors Installation Instructions | sps.honeywell.com/ast | 4 SNG-S SERIES SPEED SENSORS Issue D 32347440 FIGURE 4. CUSTOMER INTERFACE BORE m WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicable warranty period. Honeywell's standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer's sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer's sole responsibility to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this writing. However, Honeywell assumes no responsibility for its use. Honeywell Advanced Sensing Technologies 830 East Arapaho Road Richardson, TX 75081 sps.honeywell.com.ast FOR MORE INFORMATION Honeywell Safety and Productivity Solutions services its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing or the nearest Authorized Distributor, visit our website or call: USA/Canada Latin America Europe Japan Singapore Greater China +1 302 613 4491 +1 305 805 8188 +44 1344 238258 +81 (0) 3-6730-7152 +65 6355 2828 +86 4006396841 32347440-D-EN | D | 05/21 © 2021 Honeywell International Inc. All rights reserved.