Anviz Global | Secure workplace , Simplify management
bit.ly/2J9qA95SoftwareUpdata - Google Drive
User Guide for ANVIZ models including: M-Bio, Desktop and Wireless Fingerprint and Card Terminal
ORLD POWERING A SMARTER WORLD and Wireless Fingerprint and Card Terminal M-Bio Quick Guide RFID Card X4 Device USB Cable Quick Guide Notification: 1. Please check if the package contains all the items listed above.
1. Please check if the package contains all the items listed above. Contact the distributor if there is any problem. 2. Please keep the product away from the magnetic eld, and avoid.. View
File Info : application/pdf, 4 Pages, 633.34KB
DocumentDocumentPOWERING A SMARTER WORLD M-Bio Desktop and Wireless Fingerprint and Card Terminal Quick Guide Package List POWERING A SMARTER WORLD M-Bio Outdoor Fingerprint & Card Reader/Controller Quick Guide POWERING A POWERING A SMARTER W SMOARRLTDER WORLD Device X4 USB Cable Quick Guide RFID Card Notification: 1. Please check if the package contains all the items listed above. Contact the distributor if there is any problem. 2. Please keep the product away from the magnetic field, and avoid causing any damage to the device. 3. Please use the original power supply or refer to the instruction to get the right power supply. 4. Please strictly follow the instructions to install the product. Any damage to it caused by incorrect operation and wiring are not under warranty. 1 Illustration for Placing Finger Correct Method ( Straighten your finger and then place it on the sensor Ensure the finger is flat and covers the entire sensor) Always place finger in the center of the sensor. Incorrect Method Try to place your finger covers the entire sensor. Appearance Fingerprint Sensor OLED Screen Power Over USB Port Fingerprint Sensor Power Button the sensor backlight turns off. DO NOT place finger away from the center of the sensor. DO NOT place finger at an angle. Date and Time Battery WIFI AP Mode DO NOT take off finger during the fingerprint verification process. DO NOT just use your fingertip. DO NOT slide your finger during the fingerpint verification process. 2 2021 01 10 14:20:33 AP192.168.2.234 Bluetooth 3 Operation Guide IMPORTANT: M-Bio is suitable for USB 5V power supply only. Power on the device still the device screen display as below: Register User: Add One Fingerprint per User Only: Note: 1. After finish enrolling current user, the device will continue to register another user. 2. After finish enrollment, please swipe enroll card to exit enroll status. 4. Continue to register another user 2. Place finger 3. Place finger again Exit Enrollment Notice: During the device in the regsiter mode without any operation for 3 sec the M-bio will back to the normal mode. 1. Swipe Green Enroll Card & Blue lights up Blue LED and Green LED lights up 5. Swipe Enroll fingerprint sensor and display Save lights up Successed Card to end the enrollment Add Card Only: Note: 1. After finish enrolling current user, 2. After finish enrollment, please swipe enroll card to exit enroll status. 4. Continue to register another user 2. Swipe User Card 3. Swipe User Card again Exit Enrollment Notice: During the device in the regsiter mode without any operation for 3 sec the M-bio will back to the normal mode. 1. Swipe Enroll Card Green & Blue lights up Blue LED and fingerprint sensor lights up 5. Swipe Enroll Card to end the enrollment. Green LED lights up and display Save Successed Operation Guide Delete User: Delete Fingerprint or Card 4. Continue to delete After delete one user, you can continue to delete another user or swipe Delete Card to exit delete mode. 2. Place finger 3. Place finger again Notice: During the device in the delete mode without any operation for 3 sec the M-bio will back to the normal mode. 5. Swipe Delete Card to end 1. Swipe the process Delete Card Red and Blue LED Light Blue LED and Green LED lights up and display delete success Up FingerPrint sensor lights up Delete Card: After delete one user, you can continue to delete another user or swipe Delete Card to exit delete mode. 4. Continue to delete Notice: 1. Swipe Delete Card 2. Swipe User Card 3. Swipe User Card again 5. Swipe Delete Card to end the process Red and Blue LED Light Up Blue LED and FingerPrint sensor Green LED lights up lights up and display delete success When you swipe card on M5 Pro, Red LED flashing with long beeps means the card does not exist in the device. 4 5 Login WebServer 2021 01 10 14:20:33 AP192.168.2.1 Login to M-bio Webserver to manage the device. M-bio is default with WIFI AP funciton. Please connect M-Bio WIFI AP WIFI SSID: M-bio Default Password: 123456789 In order to protect the environment, Anviz has decided to go "CD Free" campaign since June 1st 2019. We will provide QR code for you to download the electronic documents to make sure that you understand how to install and use Anviz devices. User Network Basic Setting Advance Setting User: 1/10000 The Webserver Login Account: admin Password: 12345 Record: 6/100000 Anviz brand and product are trademarked and protected under law of the United States. Unauthorized use is prohibited. For more information, please visit www.anviz.com , or send email to sales@anviz.com for more help. © 2021 Anviz Global Inc. All Rights Reserved. 202101 6 CrossChex Mobile App https://bit.ly/2Vn0wh6 Google https://bit.ly/2J9qA95 Anviz 1