Instruction Manual for AFX MOTORSPORTS models including: ACC108 Frontal Rack, ACC108, Frontal Rack, Rack
Installation Manuals | AFXMotorsports
4 Attach the clamps to the side pieces with the 1/4" x 1/2" screws and 1/4" washers (included in the package), do not tighten screws. FRONTAL RACK INSTALLATION MANUAL 5 Once the front rack is assembled, attach it to the sides of the front of the vehicle through the clamps with the 1/4" x 2 1/2" screws and the 1/4" washers. Finally put the special clamp with the 1/4" x 1/2" screws attached to the car and the side plates and tighten all the screws. Clamp Special clamp 1/4" x 1/2" screws and nut 1/4" x 2 1/2" washer and nut info@afxmotorsports.com THIS PRODUCT IS FOR OFF ROAD USE ONLY POLARIS RANGER 570 2017-2022 ACC108 FOR PURCHASING AT AFX MOTORSPORTS HOW TO INSTALL (x1) Base (x2) Cornerbacks First attach the front plate to the base with the 1/4" x 1/2" bolts and 1/4" nuts. 1/4" X 3/4" Screws Front Plate 1/4" nuts Base (x1) Front plate (x2) Side pieces (x2) Clamps (26x) 1/4" X 1/2" Screws and nuts. (2x) 1/4" x 2 1/2" Screws and nuts. (2x) 1/4" Washers. 3/4" Wrench. 7/32" Allen Key. 7/16" or 14 mm Combination Wrench. Liability Statement AF1 Motorsports products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by AF1 Motorsports and is not recommended. AF1 Motorsports products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact AF1 Motorsports to verify that they will work together. Although AF1 Motorsports has thousands of satisfied customers, user should be aware that installing bumpers, rock sliders, spare tire carriers, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. AF1 Motorsports urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing AF1 Motorsports products, user agrees that should damages occur, AF1 Motorsports will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. AF1 Motorsports, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from AF1 Motorsports. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. AF1 Motorsports will warranty only parts provided by AF1 Motorsports. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by AF1 Motorsports. AF1 Motorsports parts and products are not warrantied if item was not installed properly, misused, or modified. Image 1. Front Plate 2 Attach the cornerbacks to the base and front plate with the 1/4 x 1/2" screws and 1/4" hex (included in the package). Do not tighten the screws yet. Front Plate Base Cornerbacks 1/4" nut Image 2. Pilot cornerback 3 Attach the cornerbacks to the side pieces and to the base with the 1/4" x 1/2" screws (included in the package). Do not tighten screws. Base Cornerbacks 1/4" x 1/2" screws Image 3. Pilot side pieces Side pieces 1/4" nutAdobe PDF library 10.01 Adobe Illustrator(R) 16.0