Large-scale & High performance 3D printers | CreatBot
User Manual for CreatBot models including: D600, D600 Pro, D600 D600 Pro 3D Printer, 3D, Printer, 3D Printer, D600 3D Printer, D600 Pro 3D Printer
CreatBot D600 | Op til 600x600x600 mm - 3dprinteq
File Info : application/pdf, 39 Pages, 6.30MB
DocumentDocumentCreatBot 3D Printer User manual English V7.3 Pro Henan Suwei Electronics Technology Co., Ltd. - 1- CONTENTS Notice ················································ 3 Machine Diagram Front ············································ 4 New Printer Head ··················· 5 Printer Operation Leveling Platform ··················· 6 Paving Crepe Paper ··············· 6 Load Filament ·························· 7 Unload Filament ····················· 8 Main menu ······························· 9 Status page ······························ 10 Detail page ······························· 11 Printing page ··························· 12 Axis operation ························· 13 Filament menu ························ 14 SD Card/U-disk ······················· 15 Setting menu ··························· 16 Info. menu ································· 16 Software Operation CreatWare Setup ·················· 18 Quick Print UI ······················· 19 Print Your First Model ········ 19 Full Setting UI ······················· 20 Mouse Operation ················ 21 Model Rotate/Scale ············ 21 Model Mirror ·························· 22 View Mode ······························ 23 Right Click on Model ··········· 24 Toolpath Structure ················ 24 Basic Setting ··························· 25 Advanced Setting ················· 26 Expert Setting ························ 27 Skirt/Brim/Raft······ · ····· ······· · ·· 28 Plugins ····································· 28 Start/End GCode ·················· 29 Dual Head Printing ·············· 29 Align Dual Head Horizon ··· 30 Align Dual Head Vertical ···· 31 Add Multi Type Printer ······· 31 Using skills Installation section ·············· 32 Software ·································· 33 Change filament ··················· 33 Frequently Asked Questions Paving Kapton ······················ 34 Change Fuse ·························· 35 Adjust Z Limit ························ 35 Print PLA and ABS ··············· 35 Specifications ······························ 36 Icon conventions Tip icon to remind users to have a good method or technique. Note icon, to remind the user must be given adequate attention. Prohibition icons, prevents users from unauthorized operation. 7/22/ 2017 - 2- Notice Read First Thank you for choosing CreatBot 3D printer! This manual contains important information about the installation, use, maintenance and common problems of CreatBot 3D printer. Please read this manual carefully before using 3D printer. All losses caused by the breach of the notes and the operation process of the operation process will be borne by the user. Please use the filament provided by CreatBot, or high quality filament by third manufacturers. Due to the use of third party inferior material caused by the failure of the printer, the loss will be borne by the user. Software running environment, 2G or above processors, at least 1G memory, compatible with Windows, MAC, or Linux, please use memory as much as possible. I wish you have fun with CreatBot 3D printer! Danger Warning The nozzle's temperature will reach 300 degrees, don't touch. The platform's temperature will reach 120 degrees, don't touch. Please make sure that the printer connected to the ground. Do not attempt to open the case, be careful of electric shock. Working Environment The 3D printer can work in the indoor environment of 5 to 30 . Long-term not use of the printer, be sure to keep off dust, moisture. Long-term not use of the filament, please be sealed to prevent deterioration. - 3- Machine Diagram Front 6 Touch screen 5 Power switch 4 U disk input 3 Indicator light 2 Universal Wheel 1 USB input - 4- Machine Diagram New Printer Head 14 1 13 2 3 4 5 6 7 8 1. PCB box 2. X limited switch 3. Extruder motor 4. Filament press button 5. Heatbreak 6. Heat block 7. Nozzle 8. Cooling fan 9. Thermistor 10. Heating tube 11. Heat sink 12 11 10 9 12.Extruder box 13.Connector 14.Feeding tube 5+6+7.Hotend - 5- Machine Diagram D600 Pro upgraded in 3 more key functions compared to D600 printer. Auto leveling system (Available on D600 Pro) Auto-leveling working plate make leveling easily Hot Chamber system can make inside temperature up to 70 degree. - 6- Filament dry room have 2 temperature options to set. (45 degree /65 degree.) Printer Operation Leveling Platform Printer without Auto Leveling- Leveling platform manually 1. Turn on machine 2. On touch screen, choose "Move axis" -> "All home", make nozzle close to platform. 3. Then choose "Move axis" again, -> 10mm -> -Z once. Then check the distance between nozzle and platform. (0.2mm) 4. Move (push) print head to print area alone 4 corners by hands and tighten or loosen 4 black nuts at the same time to down or up the bed. (Tight nut will lower bed; loose nut will raise bed) 5. Make sure the distance between nozzle and bed is 0.2mm around. (distance approximately the same thickness as that of one name card) Printer with Auto leveling 1: Enter Setting->Auto leveling ->Probe. Machine will start to detect 25 points. 2. If the distance too far, increase Ser vo Z offset value (+0.2mm each time). If too close or touch the bed, decrease Servo Z offset value. (-0.2mm each time). 3. Make sure the distance between nozzle and bed is 0.2mm around. Note: Servo Z offset means vertical height between nozzle and detector when probe needle outstretch. It is a fixed value if you don't change hotend or detector. Contact us for videos. Or Youtube enter keywords "CreatBot D600 leveling bed" - 7- Printer Operation Load Filament Preheat head Straightened filament Load filament Tighten the nut 1.Preheat the hotend before loading filament. 2.Straightened filament and check the filament do not self-winding. 3.load filament,and fix it on the filament shelf. 4.Twist off quick fitting, load the filament until filament beyond quick fitting. Insert filament to extruder hole manually and through it until melted and flowing naturally.(Or choose extrude filament on touch screen). Tight quick fitting. 5.Tighten the compression nut, tightness appropriately. Do same like the photo in red area. (Do not overtight, otherwise filament will be cut off. ) Notice: Pressed filament too tight or too loose will affect normal wire feeding. - 8- Printer Operation Unload/Change Filament Preheat Move axis Filament USB Status Settings Unload filament menu 0 Extrude 75 150 Head 1 Retract Unload 225 300 Preheat head 0 Extrude 75 150 UnloadinHgeafdi1lament... Retract Unload 225 300 Unloading filament Pull out filament 1. Enter "Filament" menu ->"Unload filament", and select the head you want unload. 2. Wait for the nozzle heated to a suitable temperature. 3. After reching temperature, feeder will send a certain number of filament, and then automatically withdraw filament. 4. To manually unload filament, same as above mentioned. - 9- Printer Operation Touchscreen Main Menu Preheat Moveaxis Filament U-disk Status Settings Preheat PLA Cool down Move axis Filament menu Check Status Setting Open U-disk USB unavailable - 10 - Printer Operation Status Page 210 200 210 200 45 40 Print speed:100% Fan speed :100% Flow :100% X: 0.00mm Y: 0.00mm Z: 0.00mm 210 Touch and set up the temp of the nozzle. 22000.0 210 Target temp.1 220000.0Current Temp.1 45 Touch and set up the temp of the hotbed 4455 Tar.hotbed.temp 4400.0 4400.0 Cur.hotbed.temp Print speed100% Printing speed Fan speed 100% Fan speed Flow 100% Flow X:00.00 X,Y,Z current Y:00.00 position of Z:00.00 hotend. Use information Back - 11 - Printer Operation Detail page 210C 210C 210C 210C 45C 45C Print speed:100% Flow:100% Fan speed:100% Z: 0.00mm 210 Touch and set up the temp of the nozzle. 210 Target temp.1 200 200 Current Temp.1 45 40 Touch and set up the temp of the hotbed. 45 Tar.hotbed.temp 40 Cur.hotbed.temp 50.00% Current printing progress Print speed:100% Fan speed:100% Printing speed Fan speed Flow:100% Z: 0.00mm Flow Current Z position Use information Setting Back - 12 - Printer Operation Printing page Heating: 01.30.00 50.00% Change Pause Stop 50.00% Current printing progress Heating: 01.30.00 Time printed Pause and Change filament. Continue printing Pause print Cancel print Z Z up Z Z down - 13 - Printer Operation Filament menu 10 0 75 150 225 300 Head 1 Head 2 Unload Retract Extrude Click and enter 10 a value 0 75 Adjust value when 150 extrude/retract filament 225 300 Unload Retract filament #1 extruder Head 1 #2 extruder (unavailable) Head 2 Extrude filament Retract filament Back - 14 - Printer Operation Axis operation X Home +Y -Z 0.1mm 1mm YHome -X +X 10mm ZHome -Y +Z 100mm All Home X:000.00 Y:000.00 Z:000.00 1mm Minimum units X Home Move X to home ±X/Y Move X/Y axis Y Home Move Y to home -Z Z up Z Home Move Z to home +Z Z down X: 00.00 X,Y,Z current Y:00.00 position of Z:00.00 hotend. All Home All axis to home Back - 15 - Printer Operation SD Card/U-disk file1.gcode file2.gcode file1.gcode Click and choose a file2.gcode file to print Last page Next page Superior menu Back - 16 - Printer Operation Setting menu Motor X step: 106.6666 Y step: 106.6666 Z step: 640.0000 E step: 130.0000 Reset Preheat Extruder temp.: 210 Fan speed : 0% Bed temp.: 45 More Save Fanspeed Sink fan speed: Filter fan speed : X step: 106.6666 Y step: 106.6666 Z step: 640.0000 X/Y/Z and exturder motor E step: 130.0000 setting (range:5-9999) Extruder temp. 210 Fan speed : 0% Bed temp: . 45 Preheat setting. Hotend (range 0~400) Fan speed range 0-100) Bed temp.(range 0-120). Sink fan speed: 100 % Filter fan speed : 100 % Sink fan speed (range 0-100) Filter fan speed (range 0-100) Reset Save Back - 17 - Printer Operation Info. page 3D Printer Time used 0000:00:00 Firmware 5.2.160810 Henan Suwei Elec. Tech. Co,. Ltd. www.CreatBot.com +86 4000 558 930 sales@creatbot.com 3D V4.3 Time used Print time used 0000:00:00 V4.3 Screen version Firmware Firmware version 5.3 Back - 18 - Software Operation CreatWare Setup Download CreatWare installation package from the CD-ROM or www.CreatBot.com, follow the prompts to install the software, tr y using the default installation path as well. Please associated common 3D file format. Installation path can not contain non-Latinn characters. Please associated common 3D file format. When there is a driver digital signature, please choose to agree. When finished the driver folder will locate at installation directory. The software will select the correct language according to your OS, please select the right machine type and number of nozzles and ignore the other option and guide. - 19 - Software Operation Quick Print UI 1 Load model 3 Save toolpath 2 Normal Overhang Transparent X-Ray Layers When insert U-disk, the toolpath will saved to the U-disk. The file name can not contain non-Latinn characters. Print Your First Model Insert U-disk to the card reader, open the CreatWare, load 3D model file[1], choose correct filament and option [2], finally click save button[3], you can now finish slice model. Insert U-disk to the printer, browse and select the Gcode file you just saved, the printer will automatically start to heating, when the temperature reaches, the printing will start. - 20 - Software Operation Full Setting UI Load model Save toolpath Manual slicing View mode Setting area View area Rotate Zoom Mirror As you can see from the complete UI, the left side of the software is setting area, the right side is view area. The setting area contain "Basic", "Advanced", "Plugins", "Start/End GCode" four tabs. The Basic tab is the most common settings, usually the most frequently used parameters are here. Each parameter has a mouse-over tips, you can set parameters according the prompt. If you want to restore the default settings, please click on the menu "Tools"->"Restore Default". Tip: Double-click view area can quickly load 3D model file. The view mode and edit icon will appear when you select the 3D mode. - 21 - Software Operation Mouse Operation Left click Select model, hold and move to change position, double-click to load 3D models. Right click Hold and move to rotate the viewpoint around the 3D model. Left + Right Hold and move the mouse to zoom. Scrollwheel Use the scroll wheel to zoom in or out. + Shift Left + Shift Click and drag in rotary model can according to each 1 degree angle. + Shift Right + Shift Hold and move the mouse to pan the 3D view. Keyboard Shortcut Ctrl+L Load model/Picture Delete Remove model Ctrl+E Export setting Ctrl+S Save model as F5 Refresh view area Ctrl+, Preferences - 22 - Software Operation Model Rotate Click on the left corner of the rotate button [1], you can see three ring line around the model, respectively along the X, Y, Z direction. The default rotation angle is 5 degrees, 3 press the Shift key can restrict the rotation angle to 1 degree. 2 Button [2] to is the reset button, can restore rotate status 1 to the default state. Button [3] is lay flat button, can lay the model flat on the platform automatically. Model Scale Click the left corner of the zoom button [1], you can see a contour line around the model, and shows the current size of the model. You can input the value of the zoom ratio in Scale X / Y / Z , may also directly enter the size you need. Button [4] indicates 3 locking scaling. Button [2] is zoom reset 2 button, you can restored the 4 model to the default size. 1 Button [3] for the zoom model size to the maximum print size. - 23 - Software Operation Model Mirror Click the mirror button [1], you can pop up the mirror menu. Button [2] is a mirror along the X axis. 4 Button [3] is a mirror along the Y axis. 3 Button [4] is a mirror along the Z axis. 2 Note that the mirror transformation is different from 1 the rotation, such as the mirror transformation will lead to a change in the direction of rotation, and the rotation will not change the model. View Mode From the overhang view, you can see the suspended part of the model which is shown in red color. By changing the supporting angle can be seen suspended parts size is dynamically changing. By slice view can easily observe the generated path, you can easily observe the different layers of sliced by slicing altitude indicator, use Ctrl + arrow keys can also be observed layer-by-layer. - 24 - Software Operation Right Click on Model 1 Right-click on the model pop-up shortcut 2 menu, here are more features: 3 [1] "Centered" make the model back to the center position of the platform. [2] "Delete" to 4 remove the currently selected model. [3] "Multiply" 5 to copy the currently selected model and 6 automatically position, which is useful for printing more than one model at a time. [4] "Split" multi- component model can be split into its separate components, this process more time- consuming, try to split the model in the modeling software, models splited can be printed individually and then assembled together . [5] "Delete All" to delete all the models loaded. [6] "Reload all" Reload all models, same as F5. 3 4 Toolpath Structure Red represents "outer shell" Yellow represents "infill" Green represents "inner shell" Blue represents "support" Purple represents "bottom and top shell" Drag layer indicator can browse different level paths, Ctrl + arrow keys to browse layer by layer. 3D printing is the superposition of these different layers and built layer by layer. - 25 - Software Operation Basic Setting Layer height: This is the most important setting to determent the quality of your print, maximum value not exceed 80% of the nozzle diameter. Shell thickness: Refers to the total thickness of the inner and outer walls, the outer wall is only one, the inner wall can be more, set this value to an integer multiple of the diameter of the nozzle. Flow: Refer to the amount of printing material, 100% standard dosage, the more material the model prints more plump. top/bottom thickness: Is the thickness of the upper and lower models, usually a multiple of layer height. Fill density: Control how density filled the insides of your print will be, a value around 20% is usually enough, 0% for hollow. Print speed: Speed at which printing happens. Print speed is affected by many factors, it is recommended to use low speed for complex model, high speed will cause the feed shortage, need improve nozzle temperature to compensate. Nozzle temperature: Is the melting temperature of filament, general use 200 for PLA and 240 for ABS. Bed Temperature: General use 45 for PLA and 70 for ABS. Default main head: The default is the first nozzle, can also be set to other nozzles, this can reduce the times of changing filament. Support type: The touching build plate support type is shown in figure [A], everywhere support is shown in figure [B]. Support angle: The larger the angle, the more support generate. Fill amount: The larger the fill, the more support generate. Platform adhesion type: The model which is not easy adhesion on the platform please use Brim, which easy to warped or ABS filament please use Raft. Support Type A B - 26 - Software Operation Advanced Setting Solid fill top: Refers to whether to print the top surface of the model, uncheck will print it with infill method. Solid fill bottom: Same as above, and so on. Spiralis print: Refers to the method of spiral printing the outer wall of the model (single layer), and this feature is very suitable for print glass vase model. Enable retraction: When the nozzle is moving over a noneprinted area, withdraw a certain length length filament to prevent overflow. Retract speed: The speed of retraction, too fast can lead motor out of step, too slow increase printing time. Retract distance: The length of the filament when enable retraction. First layer thickness: Height of the first layer of printing, generally greater than 0.15mm. First layer flow: When the set of the first layer is too high, it can be appropriate to increase the extrusion. Cut off object bottom: This can be used for objects that do not have a flat bottom. Continue print: Being "power outages continued" be substituted. Travel speed: The speed when moving over a non-printed area. First layer speed: Slightly slow speed can enhance adhesion model on the platform. Solid layer speed: The speed is a percentage here, which reference to the global print speed, a combination of different speeds, you can both get a good print quality and a faster print time. Spiralise Printing - 27 - Software Operation Export Setting Nozzle size: Set the nozzle size. Diameter: Accurate measurement of your filament gives better quality prints. Minimum travel: The minimum distance which can trigger filament retract. Minimum extrusion: The minimal amount of extrusion that needs to be done before retracting. Enable combing: Combing is the act of avoiding holes in the print for the head to travel over. Wipe tower: Is a small tower next to your print where the nozzle wipes itself clean when switching nozzles. Dual extrusion switch amount: Amount of retraction when switching nozzle with dualextrusion, a value of 15mm seems to generate good results. Cooling fan: The extra cooling fan is essential while printing small model, but when print ABS material, the max fan speed should not more than 50%. Skirt: The skirt is a line drawn around the model at the first layer. This helps to prime your extruder, and to see if the model fits on your platform. Brim: The amount of lines used for a brim, more lines means a larger brim which sticks better. Notice: Most of the setting have been optimized, If you want restore default configuration,use the menu "Tools"->"Reset profile to default". - 28 - Software Operation Skirt · Brim · Raft Adhesion type None Adhesion type Brim Adhesion type Raft Plugins Plugin enable you to easily include your own features, without having to modify the source code or Gcode. In the screen shot above, these can be enabled by clicking on the arrow down button, then you can configure the plugin. Notice: Please remove the plugin before you close the software. - 29 - 11 22 3 3 Software Operation Start / End GCode The start and end gcode are the startup and end procedure of the print, editing this requires knowledge of GCode. If you want to set the automatic heating station after printing, you can remove the ";" in the code ";M190 S50". start.gcode is the start code of single extruder, start2.gcode is the start code of double extruder, and so on. Dual Head Printing A B Step 1: Load 2 models C you want as shown in figure [A] and [B]. Step 2: Fist click [A], then right click on [B], you will get the option: dual extrusion merge, this will merge both models into one model [C]. Step 3: Set parameters like ordinary single color model and save the GCode. Tip: The model select first will print by main extruder, the right clicked one by second extruder. - 30 - Software Operation Align Dual Head Horizontal There are alignment problem while printing dual color model, this is because the small difference in multi-nozzle assembly, CreatWare built fine-tuning features. Click menu "Machine">"Machine settings", default X offset is: 20.0, default Y offset is: 0.0, adjustment method as shown below: Extruder 2 Offset X Offset Y 28.3 0.3 Extr. 1 Extr. 2 Extruder 2 Offset X Offset Y 27.7 -0.3 Extr. 1 Extr. 2 - 31 - Software Opertation Align Dual Head Vertical Step 1: loose the 2 screws with red circle. Step 2: raise or lower hotend with heads after cooling nozzle Step 3: Lower left nozzle step by step same with right nozzle. (Note: every time you raise or lower nozzle, you need to adjust the offset value in autoleveling menu) Tip: You can rising right nozzle as long time not use. Add Multi Type Printer You can add more than one type of CreatBot to the software, and easily switch between them without re-config all the different machine D600 - 32 - Software Opertation Print Setting Of Different Filament Nozzle temperature Hot bed Plantform adhesion type Fully enclose or not PLA 190~210 None/45 None/Raft Can open ABS Nylon HIPS PETG Flexible 240~250 240~270 230~260 230~260 210~230 90 100 100 100 None/45 Brim/Raft / Brim Raft / None Brim / None Brim None Enclosed Enclosed Enclosed Enclosed Can open Wood 190~220 None/45 None Can open PC 230~260 100 Brim Enclosed PEEK 380~430 Bed 120/Air 70 Raft Enclosed * The data is only for reference, different environmental data will be different.F160 and F430 can print PEEK. - 33 - Frequently Asked Questions Hardware Troubleshoot 1. Display "MINTEMP" ? The environment is too low, or temperature sensor is damaged, please keep the room temperature above 0 . 2. Display "MAXTEMP" ? Temperature of nozzle or bed too high, or temperature sensor is damaged, please keep their temperature in a suitable range. 3. USB connection problems ? Please specify the correct port and baud rate (250000), or change a shorter USB cable. 4. Nozzle heats up too slowly ? Temperature in door is too low, or use a fan duct, or turn up output voltage (24.5v). 5. Print head stuck ? Clean the guide rail and add lubricating oil. 6. Print head can not move ? Stepper motor chipset burned, or belt damaged, or belt wheel screw loose. 7. Print head hit the framework ? Corresponding axis stop limit or circuit fault. 8. Unable to power on ? Power switch is damaged or fuse is burned, and please check whether the power adapter is working properly or power check board is damaged. Printing Troubleshoot 1. How to set the temperature of the nozzle ? Different filament temperature is different, general as follows: PLA temperature 190 ~210 ,bed 45-60 . ABS temperature 230 ~250 ,bed 80-100 . You must leave enough time for filament heating, so the faster printing speed need the higher temperature, 60mm/s temperature need raise about 10. In the same way, larger thickness need higher temperature. 2. How to set the temperature of the hot bed ? The main purpose of the hot bed is to prevent model wrapped, PLA need about 45 and 70 for ABS is enough, but due to the environment and filament, we often need to increase the temperature, the highest temperature - 34 - Frequently Asked Questions Change Fuse Note: Please use the 10A fuse. Open fuse tray Change new fuse Adjust Z Limit If the nozzle can't touch the platform even loosen all the leveling nut, you can move Z stop limit a little up, as you can see from figure. Print PLA and ABS PLA ABS Nozzle 200 240 Bed 45 90 Close bed Timed close Always Adhesion None/Brim Brim/Raft Cooling Tape Enclosed Max. 100% masking Can open Max. 50% Kapton Enclosed * The data is only for reference, different environmental data will be different. - 35 - Printing Troubleshoot not over 120, and you can close the bed above 100mm except printing ABS or other high-temperature required filaments. 3. The model not stick on the platform ? Please paste masking paper or Kapton tape on the platform, or the nozzle is too far away from the platform, or the bottom of the model is not flat. 4. No or less silk coming on the first layer ? The distance between nozzle and platform is too small, or the filament has not been sent to the nozzle. 5. Why nozzle is not spit silk ? The filament is not pressed or too tight, or print temperature is too low, or the filament feeder not working. 6. How to prevent model become warped ? Increase hot bed temperature or use Kapton, or change platform adhesion type to Raft, or cover the baffle, or reduce indoor ventilation. 7. How far from nozzle to platform appropriate ? Distance should be 0 in theory, but there is no absolutely flat platform, so the distance should +-0.1mm. Finally, with the actual printing effect as the standard, too close will lead to a silk blocked, too far will cause the model not stick on the platform. 8. How to determine whether the temperature is too high ? PLA temperature is too high will appear liquefaction, ABS will be the carbide, that will block the nozzle. 9. What reasons will causing nozzle blocked ? Filament are impurities or print environment dust too much, bad of thermal conductivity between the nozzle and the heating block. 10. Model surface is loose with crack ? The layer is too high or the printing speed too fast, nozzle temperature too low or filament press nut too loose, or filament is wrapped. 11. How to print a small model ? Multiple the model, and print them at a time. 12. Dual color model not aligned ? Adjust offset of second nozzle in machine settings. 13. Dual color model color interference ? Align two nozzle in vertical direction 14. There is too much silk drag on the model ? Please enable filament retraction, and specified proper retract speed, and distance, the retract distance should not less than 4mm, and the speed not less than 10mm/s. - 36 - Specifications Model Build volume Nozzles Diameter Temperature Nozzles Type Hot bed Min. Layer Accuracy Print Speed Travel Speed Materials Fila. Diameter Motion Structures Auto Turnoff Continue Play Fila. Check Adju. Head OS Languages Software File Format Printing Field Display Pwr Supply Dimension Weight F160 F430 D600 160*160*200 400*300*300 600*600*600 Single Single/Dual 0.4mm(0.3/0.6/0.8/1.0mm can be customized) 400 360 Direct drive 140 Bed 120/Air 70 100 0.04mm X Y Z axis 0.01mm 120mm/s (inner/outter, top/bottom, fill, first layer speed can be set separately) 200mm/s ABS,PLA,TPU,PETG,HIPS,PVA, PA,PC,Carbon Fibre,PEEK,etc 1.75mm 3.0mm Optic axis Rectilinear orbit Yes (pwr manager + relay) Yes (Power outage, lower plate and save data) Yes (pause printing when filament finish, and lower platform) Yes (height-adjustable-nozzles) Windows, Linux, Mac OS, OSX Chinese, English multi-language CreatWare Muti-language STL, OBJ, GCode, Amf Full closed covering 4.3 inches color touch screen 110/220V 180W 110/220V 1300W 110/220V 1000W 280*280*470mm 660*470*560mm 910*840*1100mm 22Kg 60Kg 170Kg - 37 - Specifications Model Build volume Nozzles Diameter Temperature Nozzles Type Hot bed Min. Layer Accuracy Print Speed Travel Speed Materials Fila. Diameter Keypad Auto Turnoff Continue Play Fila. Check Adju. Head OS Languages Software File Format Chipset Display Pwr Supply Dimension Weight DX 300*250*300 DX Plus DE 300*250*520 400*300*300 Dual/Tris DE Plus 400*300*520 0.4mm(0.3/0.6/0.8/1.0mm can be customized) 400 print head/new print head 120 (can be closed after certain layers) 0.04mm X Y Z axis 0.01mm 120mm/s (inner/outter, top/bottom, fill, first layer speed can be set separately) 200mm/s ABS,PLA,TPU,PETG,HIPS,PVA, PA,PC,Carbon Fibre,etc 3.0mm (1.75mm optional) Yes (nine key) Yes (pwr manager + relay) Yes (Power outage, lower plate and save data) Yes (pause printing when filament finish, and lower platform) Yes (height-adjustable-nozzles) Windows, Linux, Mac OS, OSX Chinese, English multi-language CreatWare Muti-language STL, OBJ, GCode, Amf Atmega 2560-16AU (AVR 8 Bit 16MHz 256KB Flash) 128*64 monochrome multi-language (support color TFT) 110/220V 360W 110/220V 700W 420*380*570 420*380*790 590*430*570 590*430*790 35 Kg 40Kg 45Kg 55Kg - 38 - Quality · Experience · Service Henan Suwei Electronics Technology Co., Ltd. Telephone: +86 4000-558-930 Website: www.CreatBot.com Email: sales@creatbot.com Address: A805 XingHua Building,HangHai road, Zhengzhou City,China - 39 -